Installation
Carpet Removal and Installation
Installation
1. Rear Wheelhouse Gusset
1. Install the rear wheelhouse gusset (A), then install the bolts and the nuts.
2. Foot Stopper
1. Install the foot stopper (A). Make sure the clips (B) snap into place securely.
3. Floor Carpet
1. Install the floor mat holder (A).
2. Pass the floor wire harnesses (A) through the hole in the carpet (B), then install the carpet.
3. Install the clips (C).
4. Steering Joint Cover
1. Install the steering joint cover (A).
5. Rear Carpet Trim - Both Sides
Left side
Right side
1. Install the rear carpet trims (A). Make sure the clips (B) and the hooks (C) snap into place securely.
6. Rear Seat-Back Assembly - Both Sides
Left side
Right side
1. Install the rear seat-back assembly (A).
NOTE: Tighten the bolts (B, C) by hand first, then tighten them to the specified torque.
2. Install the rear seat-back cover (D). Make sure the clips (E) snap into place securely.
7. Right Rear Seat Cushion Assembly
1. Install the right rear seat cushion assembly (A).
NOTE: Tighten the bolts (B) by hand first, then tighten them to the specified torque.
2. Connect the cables (A) to the rear seat cushion assembly (B), then install the cables to the cable brackets (C), and install the cable clip (D).
8. Left Rear Seat Cushion Assembly
1. Install the left rear seat cushion assembly (A).
NOTE: Tighten the bolts (B) by hand first, then tighten them to the specified torque.
2. Connect the cables (A) to the rear seat cushion assembly (B), then install the cables to the cable brackets (C), and install the cable clip (D).
9. Rear Seat Cushion Foot Cover - Both Sides
Left side
Right side
1. Install the rear seat cushion foot covers (A). Make sure the clips (B) and the hooks (C) snap into place securely.
10. Rear Damper Maintenance Cover - Both Sides
NOTE: Repeat on the opposite side.
1. Fold down the rear seat-back.
2. Install the rear damper maintenance cover (A). Make sure the hooks (B) snap into place securely.
11. B-Pillar Lower Trim - Both Sides (After Removing Seats)
1. Install the B-pillar lower trim (A). Make sure the clips (B) and the hooks (C) snap into place securely.
2. Repeat this step on the opposite side.
12. Kick Panel - Both Sides
Driver's side
Passenger's side
1. Install the driver's side kick panel (A) and the passenger's side kick panel (B). Make sure the clips (C) snap into place securely.
2. Install the front door opening seal (D).
13. Rear Door Opening Seal As Needed - Both Sides
1. Install the rear door opening seal (A). Make sure the seal is installed securely into the hooks (B).
2. Repeat this step on the opposite side.
14. Front Door Opening Seal As Needed - Both Sides
1. Install the front door opening seal (A). Make sure the seal is installed securely into the hooks (B).
2. Repeat this step on the opposite side.
15. Rear Door Sill Trim - Both Sides
NOTE: Repeat on the opposite side
1. Pull the release strap to fold down the rear seat, then lift-up and latch the rear seat-back in the upright position.
2. Install the rear door inner sill trim (A). Make sure the clips (B, C), the hooks (D), and the tab (E) snap into place securely.
16. Front Door Sill Trim - Both Sides
1. Install the front door inner sill trim (A). Make sure the clips (B), the hooks (C), and the tabs (D) snap into place securely.
2. Repeat this step on the opposite side.
17. Front Seat - Both Sides
Driver's seat
Passenger's seat (Without woofer)
Passenger's seat (With woofer)
1. With the help of an assistant, carefully install both front seats through the front door opening.
2. Lift up the front seat, then connect the connectors (A) and install the harness clip (B).
3. Insert the head restraint (A) into the seat-back as shown.
4. The driver's seat is shown; repeat on the passenger's seat.
Front
Rear
5. Install the seat mounting bolts (A).
NOTE: Tighten the bolts to the specified torque in the sequence shown.
* Tighten the bolts by hand first, then tighten them to the specified torque.
* Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten 1 and 2, then slide it forward and tighten 3 and 4.
6. The driver's seat is shown; repeat on the passenger's seat.
7. Install both seat track end covers (A). Make sure the hooks (B) snap into place securely.
8. The driver's seat is shown; repeat on the passenger's seat.
18. Battery Terminal (SRS) - Reconnection
NOTE: If the battery performance is abnormal, test the battery.
1. Clean the battery terminals.
2. Connect the positive cable (A) to the battery.
NOTE: Always connect the positive side first.
3. Connect the negative cable (B) to the battery.
4. Apply multipurpose grease to the terminals to prevent corrosion.
19. Front Seat Belt Lower Anchor Bolt - Both Sides
NOTE: Repeat on the opposite side.
1. Install the lower anchor bolt.
NOTE: Before installing the anchor bolt, make sure there are no twists or kinks in the seat belt.
2. Install the anchor cover (A). Make sure the hooks (B) and the tab (C) snap into place securely.
20. Center Console
1. Install the center console (A).
2. Connect the connectors (A), and install the clips (B).
3. Install the bolts (A), then install the console box mat (B).
4. Install the bolts (A).
5. Install the bolt (A), then install the center lower cover (B). Make sure the clips (C) snap into place securely.
21. Center Console Rear Trim
1. Install the center console rear trim (A). Make sure the clips (B) and the hooks (C) snap into place securely.
22. Front Console Cover - Both Sides
Left side
Right side
1. Install the front console covers (A). Make sure the clips (B, C) snap into place securely.