Programming and Relearning

HandsFreeLink Control Unit Update

Procedure

* Before you update the HandsFreeLink control unit, make sure the battery in the vehicle is fully charged, and connect a jumper battery (not a battery charger) to maintain system voltage.
* Never turn the ignition switch to ACCESSORY (I) or to LOCK (0) during the update. If there is a problem with the update, leave the ignition switch turned to ON (II).
* To ensure the latest program is installed, do a HandsFreeLink control unit update whenever the HandsFreeLink control unit is substituted or replaced.
* The HandsFreeLink control unit is updated via Bluetooth using the HFL control unit update application on the HDS PC. Make sure the HDS PC is inside the vehicle when updating the HFL control unit.

1. HandsFreeLink Control Unit Update

With Navigation

1. Turn the ignition switch to ON (II).






2. Press and hold the MAP/GUIDE, DEST, and CANCEL buttons for 3 seconds or more, and the self-diagnosis begins.

3. When the Select Diagnosis Items menu appears, select Self-Diagnosis Mode.





4. Select the HFL from the System Links menu.






5. Open the HFL control unit update application on the HDS PC.

6. Select the Software Update from the vehicle's HFL menu.





7. A PASS (pin code) appears on the vehicle's HFL menu. To start the update, enter this PASS into the HFL control unit update application.

NOTE: If the HFL is not able to connect with the HFL control unit application after 5 minutes, the HFL control unit times out. If the control unit times out, turn the ignition switch to LOCK (0), then go to step 1 and try again.






8. When the update finishes, the message Update completed appears on the vehicle's HFL menu. Select Confirm Software Version to check that the HFL control unit is updated. If the unit did not update, turn the ignition switch to LOCK (0), then go to step 1 and try again. To end the System Diagnostic Mode, turn the audio system off, or turn the ignition switch to LOCK (0). If you cannot select the HFL from the System Links menu, go to step 9.

9. Turn the ignition switch to LOCK (0), and then back to ON (II).

10. Open the HFL control unit update application on the HDS PC.

11. Use the previously used PASS to start the HFL control unit update.

NOTE: If the HFL update was unsuccessful, the previously used pin code is displayed on the HFL control unit update application.

12. Update HFL unit. If you cannot access the unit, restart your HDS PC, then go to step 9.

13. When the update finishes, turn the ignition switch to LOCK (0), and then back to ON (II).

14. Go to the Self-Diagnosis Mode and check the software version information that appears on the vehicle's HFL menu.

Without Navigation

1. Turn the ignition switch to ON (II).






2. Make sure the audio system is turned off.

3. Push and hold the preset No. 1 and No. 6 buttons.

4. While holding the buttons, press the PWR (Power) button to on.

5. Release all the buttons, and the self-diagnosis begins.

6. Push and hold the PHONE button for 5 seconds.

7. Open the HFL control unit update application on the HDS PC.






8. Push the preset No.2 button several times until update appears on the audio display.

9. Push the VOL PUSH SELECT button.

10. A PASS (pin code) appears on the vehicle's HFL menu. To start the update, enter this PASS into the HFL control unit update application.

NOTE: If the HFL is not able to connect with the HFL control unit application after 5 minutes, the HFL control unit times out. If the control unit times out, turn the ignition switch to LOCK (0), then go to step 1 and try again.






11. When the update finishes, the message Update completed appears on the vehicle's HFL menu. Select Confirm Software Version to check that the HFL control unit is updated. If the unit did not update, turn the ignition switch to LOCK (0), then go to step 1 and try again. To end the System Diagnostic Mode, turn the audio system off, or turn the ignition switch to LOCK (0). If you cannot select the HFL from the System Links menu, go to step 12.

12. Turn the ignition switch to LOCK (0), and then back to ON (II).

13. Open the HFL control unit update application on the HDS PC.

14. Use the previously used PASS to start the HFL control unit update.

NOTE: If the HFL update was unsuccessful, the previously used pin code is displayed on the HFL control unit update application.

15. Update HFL unit. If you cannot access the unit, restart your HDS PC, then go to step 12.

16. When the update finishes, turn the ignition switch to LOCK (0), and then back to ON (II).

17. Go to Self-Diagnosis Mode and verify the HFL software is updated by pressing the preset No. 2 button several times until the software version information appears.