Shift Lock Release And Release Spring Removal And Installation

Shift Lock Release and Release Spring Removal and Installation

Removal

1. Shift Lever Panel (AT)





1. Carefully pry out the shift lever panel (A) with the appropriate trim tool to detach the clips (B, C) and the hooks (D), then remove the shift lever panel.

2. Front Console Cover - Both Sides

Left side





Right side





1. Remove the clips (A).

2. Detach the clips (B), then remove the front console covers (C).

3. Center Console Rear Trim





1. Carefully pry out the center console rear trim (A) with the appropriate trim tool to detach the clips (B) and the hooks (C), then remove the center console rear trim.

4. Center Console





1. Carefully pry out the center lower cover (A) with the appropriate trim tool to detach the clips (B), then remove the center lower cover.

2. Remove the bolt (C).





3. Remove the bolts (A).





4. Remove the console box mat (A), then remove the bolts (B).





5. Disconnect the connectors (A), and remove the clips (B).





6. Slide both front seats fully rearward, and recline the seat-backs around two thirds to the rear.

7. Remove the center console (A).

5. Center Maintenance Cover





1. Remove the maintenance cover (A).

6. Shift Cable - Disconnection Lever Side





1. Shift the shift lever to R.

2. Insert a 6.0 mm (0.236 in) pin (A) into the positioning holes (B).

NOTE: Use only a 6.0 mm (0.236 in) pin with no burrs.

3. Remove the nut (C) securing the shift cable end (D).





4. Unlock the retainer lock (A).





5. Rotate the socket holder retainer (A) counterclockwise (B) until it stops, and push the retainer lock (C) into the socket holder retainer to lock the retainer.





6. Slide the socket holder (A) away from the bracket as shown to remove the shift cable (B) from the shift cable bracket (C).

NOTE: Do not remove the shift cable by pulling the shift cable guide (D).

7. A/T Shift Lever Assembly





1. Disconnect the shift lever connector.





2. Remove the shift lever assembly.

8. D3 Switch Harness - Disconnection





1. Remove the harness wire tie (A).

2. Disconnect the D3 switch connector (B).

9. Shift Lever Knob/Shift Lever Knob Ring Assembly





NOTE: Do not wipe off the special grease applied to the area of the shift lever marked with an asterisk (*) when you disassemble or assemble it.

1. Unhook the D3 switch harness (A) from the harness guide (B).

2. Remove the shift lever knob/shift lever knob ring assembly (C).

10. A/T Gear Position Indicator Panel Assembly





1. Remove the A/T gear position indicator panel light socket (A) from the A/T gear position indicator panel assembly (B).

2. Unhook the A/T gear position indicator panel light harness (C) from the harness guide (D).

3. Remove the A/T gear position indicator panel assembly by expanding the four lock tabs (E).

11. Shift Lock Release





1. Remove the shift lock release (A) and the release spring (B) by pressing the lock tab (C).

Installation

1. Shift Lock Release





1. Install the shift lock release (A) and the release spring (B).

2. A/T Gear Position Indicator Panel Assembly





1. Install the A/T gear position indicator panel assembly (A) by aligning the four lock tabs (B).

2. Hook the A/T gear position indicator panel light harness (C) to the harness guide (D).

3. Install the A/T gear position indicator panel light socket (E).

3. Shift Lever Knob/Shift Lever Knob Ring Assembly





NOTE: Do not wipe off the special grease applied to the area of the shift lever marked with an asterisk (*) when you disassemble or assemble it.

1. Install the shift lever knob/shift lever knob ring assembly (A).

2. Hook the D3 switch harness (B) to the harness guide (C).

4. D3 Switch Harness - Reconnection





1. Connect the D3 switch connector (A).

2. Route the D3 switch harness (B) along with the shift lever assembly, and tie the harnesses at the guide (C) with the harness wire tie (D).

5. A/T Shift Lever Assembly





1. Install the shift lever assembly.





2. Connect the shift lever connector.

6. Shift Cable - Adjustment





1. Push the shift cable (A) until it stops, then release it. Pull the shift cable back one step so that the shift position is in R.

NOTE: Do not hold the shift cable guide (B) to adjust the shift cable.





2. Turn the ignition switch to ON (II).

3. Check that the R position indicator comes on.

4. Turn the ignition switch to LOCK (0).





5. Shift the shift lever to R.

6. Insert a 6.0 mm (0.236 in) pin (A) into the positioning holes (B).

NOTE: Use only a 6.0 mm (0.236 in) pin with no burrs.





7. Unlock the retainer lock (A).





8. Rotate the socket holder retainer (A) clockwise (B) until it stops to create clearance (C) between the socket holder (D) and holder retainer, and push the retainer lock (E) into the socket holder retainer to lock the retainer.





9. Align the shift cable slot (A) between the socket holder (B) and the socket holder retainer (C) with the opening (D) in the shift cable bracket (E), then slide the holder into the bracket while installing the shift cable end (F) over the mounting stud (G) by aligning its square hole (H) with the square fitting (I) at the bottom of the stud.

NOTE:
* Do not install the shift cable by holding the shift cable guide (J).
* When the socket holder is installed in the shift cable bracket, the retainer lock is unhinged and releases the holder retainer lock, then the holder retainer returns under spring force to secure the shift cable.





10. Push the retainer lock (A) fully to lock the socket holder retainer (B), and make sure that the retainer lock fits into the hinged-joint (C). If the retainer lock does not fit with the edge of the hinged-joint, rotate the holder retainer counterclockwise while pushing the retainer lock until it locks.





11. Make sure that the shift cable end (A) is properly installed on the mounting stud (B).

* If the shift cable end is out of position with the mounting stud, remove the shift cable from the shift cable bracket, then reinstall the cable end over the mounting stud before reinstalling the shift cable to the shift cable bracket. Do not install the shift cable end on the mounting stud with the shift cable install on the shift cable bracket.
* If the shift cable end does not ride at the bottom of the mounting stud, rotate the stud to align the square fitting with the hole.





12. Install the shift cable end nut (A).

13. Remove the 6.0 mm (0.236 in) pin (B) that was installed to hold the shift lever.

14. Turn the ignition switch to ON (II).

15. Move the shift lever to each position, and check that the A/T gear position indicator follows the transmission range switch.

16. Shift the shift lever to P.

17. Check that the shift lock works properly.

18. Push the shift lock release, and check that the shift lever releases. Also check that the shift lever locks when it is shifted back to P.

19. Turn the ignition switch to LOCK (0).

7. Center Maintenance Cover





1. Install the maintenance cover (A).

8. Center Console





1. Install the center console (A).





2. Connect the connectors (A), and install the clips (B).





3. Install the bolts (A), then install the console box mat (B).





4. Install the bolts (A).





5. Install the bolt (A), then install the center lower cover (B). Make sure the clips (C) snap into place securely.

9. Center Console Rear Trim





1. Install the center console rear trim (A). Make sure the clips (B) and the hooks (C) snap into place securely.

10. Front Console Cover - Both Sides

Left side





Right side





1. Install the front console covers (A). Make sure the clips (B, C) snap into place securely.

11. Shift Lever Panel (AT)





1. Install the shift lever panel (A). Make sure the clips (B, C) and the hooks (D) snap into place securely.