Rear Door Window Glass: Service and Repair

Rear Door Glass Removal and Installation

Removal

1. Rear Door Power Window Switch Panel





1. Carefully pry out on the notch (A) in the power window switch panel (B) with the appropriate trim tool to detach the clips (C) and the hooks (D). Disconnect the connector (E), then remove the power window switch panel.

2. Rear Door Panel





1. Detach the clip (A) and the hooks (B), then remove the rear door quarter inner trim (C).





2. Carefully pry out on the upper hook (A) in the inner handle cap (B) with the appropriate trim tool, then pull back the inner handle cap to remove it.





3. Remove the screws (A) securing the inner handle (B).





4. Remove the pull pocket mat (A), then remove the screws (B).





5. Starting at the bottom edge of the door panel (A), detach the clips (B) with a commercially available trim pad remover.

6. Starting at the rear, pull the door panel up.

7. Remove the inner handle (C) from the door panel, then remove the door panel.

3. Rear Door Plastic Cover





1. Disconnect the connector (A), then remove the harness clips (B).

2. Remove the screws (C), then remove the door pull pocket bracket (D).

3. Remove the plug caps (E), then carefully remove the plastic cover (F).

NOTE: If the plastic cover is damaged or torn, replace it.

4. Rear Door Glass





1. Carefully move the glass (A) until you can see the glass mounting bolts (B), then remove them. Carefully lower the glass into the door. Take care not to drop the glass inside the door.





2. Remove the nut (A) and the bolt (B) securing the rear door rear lower channel.

3. Carefully pull out the glass (C) through the window slot. Take care not to drop the glass inside the door.

5. Rear Door Glass Run Channel





1. Remove the rear door glass run channel (A).

6. Rear Door Rear Lower Channel





1. Remove the rear door rear lower channel (A).

Installation

1. Rear Door Rear Lower Channel





1. Install the rear door rear lower channel (A).

2. Rear Door Glass Run Channel





1. Install the rear door glass run channel (A) all the way around.

3. Rear Door Glass





1. Install the glass (A) through the window slot.

2. Install the nut (B) and the bolt (C) securing the rear door rear lower channel.





3. Install the glass mounting bolts (A) securing the rear door glass (B).

4. Rear Door Glass - Adjustment





NOTE:
* Check the weatherstrip and the glass run channel for damage or deterioration, and replace them if necessary.
* Wipe the run channel clean with a shop towel.

1. Place the vehicle on a firm, level surface.

2. Carefully move the glass (A) until you can see the glass mounting bolts (B), then loosen them.

3. Push the glass against the front side channel, then tighten the glass mounting bolts.

4. Make sure that the glass moves smoothly.





5. Raise the glass fully, and check for gaps. Also make sure that the glass (A) contacts the glass run channel (B) evenly.

5. Rear Door Plastic Cover





1. Install the plastic cover (A), then install the plug caps (B).

2. Install the pull pocket bracket (C), then install the screws (D).

3. Connect the connector (E), then install the harness clips (F).

6. Rear Door Panel





1. Install the inner handle (A) in the door panel (B).

2. Install the door panel. Make sure the clips (C) snap into place securely.





3. Install the screw (A), then install the pull pocket mat (B).





4. Install the screws (A) securing the inner handle (B).





5. Install the inner handle cap (A). Make sure the upper hook (B) and the lower hooks (C) snap into place securely.





6. Install the rear door quarter inner trim (A). Make sure the clip (B) and the hooks (C) snap into place securely.

7. Rear Door Power Window Switch Panel





1. Connect the connector (A), then install the power window switch panel (B). Make sure the clips (C) and the hooks (D) snap into place securely.