DTC Troubleshooting

Control System DTCs

DTC Troubleshooting: P0462

DTC P0462 : Fuel Level Sensor (Fuel Gauge Sending Unit) Circuit Low Voltage

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information How to Troubleshoot the Fuel And Emissions Systems.


1. Problem verification:

-1. Turn the ignition switch to ON (II).

-2. Clear the DTC with the HDS. How to Troubleshoot the Fuel And Emissions Systems

-3. Wait 5 seconds.

-4. Check for Pending or Confirmed DTCs with the HDS.

Is DTC P0462 indicated?
-YES- The failure is duplicated. Go to step 2.
-NO- Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the gauge control module and the fuel gauge sending unit.

2. Fuel gauge sending unit check:

-1. Turn the ignition switch to LOCK (0).

-2. Remove the access panel from the floor.

-3. Disconnect the following connector.






-4. Turn the ignition switch to ON (II).

-5. Wait 5 seconds.

-6. Check for Pending or Confirmed DTCs with the HDS.

Is DTC P0463 indicated?
-YES- Replace the fuel gauge sending unit Fuel Tank Unit Disassembly And Reassembly, then do the repair verification.
-NO- The fuel gauge sending unit is OK. Go to step 3.

3. Determine possible failure area (FUEL GAGE+ line, others):

-1. Measure the voltage between test points 1 and 2.










Is there battery voltage?
-YES- Go to step 5.
-NO- Go to step 4.

4. Shorted wire check (FUEL GAGE+ line):

-1. Turn the ignition switch to LOCK (0).

-2. Remove the gauge control module. Service and Repair

-3. Disconnect the following connector.






-4. Check for continuity between test points 1 and 2.










Is there continuity?
-YES- Repair a short in the FUEL GAGE+ wire between the gauge control module and the fuel tank unit, then do the repair verification.
-NO- The FUEL GAGE+ wire is OK. Replace the gauge control module Service and Repair, then do the repair verification.

5. Gauge control module check:

-1. Reconnect the following connector.






-2. Remove the fuel tank unit. Fuel Tank Unit Removal/Installation

-3. Connect the following connector.






-4. Turn the ignition switch to ON (II).

-5. Clear the DTC with the HDS. How to Troubleshoot the Fuel And Emissions Systems

-6. Set the float (A) to the E position.






-7. Check the fuel gauge.

Does the gauge move to the empty position?
-YES- The gauge control module is OK. Update the PCM PCM Update if it does not have the latest software, or substitute a known-good PCM Service and Repair, then do the repair verification.
-NO- Replace the gauge control module Service and Repair, then do the repair verification.

Repair verification:

-1. Turn the ignition switch to LOCK (0).

-2. Reinstall all removed parts in the reverse order of removal.

-3. Turn the ignition switch to ON (II).

-4. Reset the PCM with the HDS How to Troubleshoot the Fuel And Emissions Systems.

-5. Do the PCM idle learn procedure PCM Idle Learn Procedure.

-6. Check for Pending or Confirmed DTCs with the HDS.

Is DTC P0462 indicated?
-YES- Check for poor connections or loose terminals at the gauge control module and the fuel gauge sending unit. If the PCM was updated, substitute a known-good PCM Service and Repair, then recheck. If the PCM was substituted, go to step 1.
-NO- Troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other Pending or Confirmed DTCs are indicated, go to the indicated DTC's troubleshooting.