Except FFV Model
DTC Troubleshooting: P0982 (60-3)
DTC P0982:
Shift Solenoid Valve D (Short)
NOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review the General Troubleshooting Information How To Troubleshoot The A/T System.
- This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine in P, and wait for at least 1 second.
4. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0973 or P0982 indicated?
YES -
If DTC P0973 is indicated, go to the DTC P0973 troubleshooting Except FFV Model. If DTC P0982 is indicated, go to step 8.
NO -
Go to step 5.
5. Select Shift Solenoid Valve D in the Miscellaneous Test Menu, and test the shift solenoid valve D with the HDS.
Is a clicking sound heard?
YES -
Go to step 6.
NO -
Go to step 8.
6. Start the engine in P, and wait for at least 1 second.
7. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES -
Go to step 8.
NO -
If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM. If the HDS indicates NOT COMPLETED, go to step 5.
8. Turn the ignition switch to LOCK (0).
9. Jump the SCS line with the HDS.
10. Disconnect PCM connector C (49P).
11. Measure the resistance between PCM connector terminal C9 and body ground.
Is there less than 12 Ohms?
YES -
Go to step 12.
NO -
Go to step 15.
12. Disconnect the shift solenoid wire harness connector.
13. Check for continuity between PCM connector terminal C9 and body ground.
Is there continuity?
YES -
Repair a short to body ground in the wire between PCM connector terminal C9 and the shift solenoid wire harness connector, then go to step 20.
NO -
Go to step 14.
14. Inspect shift solenoid valve D and shift solenoid wire harness Shift Solenoid Valve Test, Replacement, And Shift Solenoid Wire Harness Replacement.
Is shift solenoid valve D and shift solenoid wire harness OK?
YES -
Go to step 15.
NO -
Replace shift solenoid valve D or the shift solenoid wire harness Shift Solenoid Valve Test, Replacement, And Shift Solenoid Wire Harness Replacement, then go to step 20.
15. Reconnect all connectors.
16. Update the PCM if it does not have the latest software PCM Update, or substitute a known-good PCM.
17. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
18. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0982 indicated?
YES -
If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1.
NO -
Go to step 19.
19. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM PCM Replacement (Except FFV Model). If any other Pending or Confirmed DTCs were indicated in step 18, go to the indicated DTC's troubleshooting.
NO -
If the HDS indicates FAILED, check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM. If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step 17.
20. Reconnect all connectors.
21. Turn the ignition switch to ON (II).
22. Clear the DTC with the HDS.
23. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
24. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0982 indicated?
YES -
Check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM, then go to step 1.
NO -
Go to step 25.
25. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 24, go to the indicated DTC's troubleshooting.
NO -
If the HDS indicates FAILED, check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, go to step 23.