DTC Troubleshooting
DTC Troubleshooting: P0713 (28)
DTC P0713:
ATF Temperature Sensor (Open)
NOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review the General Troubleshooting Information How To Troubleshoot The A/T System.
- This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
- Some wire colors and PCM connector terminal arrangement vary according to the model year, and are indicated with an asterisk as follows:
- *1: '09-11 models
1. Check the ATF temperature sensor voltage with the HDS in the A/T Data List.
Does the ATF Temp Sensor (V) exceed 4.93 V?
YES -
Go to step 2.
NO -
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals between the ATF temperature sensor and the PCM.
2. Turn the ignition switch to LOCK (0).
3. Disconnect the ATF temperature sensor connector at the transmission end cover.
4. Connect ATF temperature sensor connector terminal No. 2 to body ground with a jumper wire.
5. Turn the ignition switch to ON (II).
6. Check the ATF temperature sensor voltage with the HDS in the A/T Data List.
Does the ATF Temp Sensor (V) drop to 0.07 V or below?
YES -
Go to step 7.
NO -
Go to step 12.
7. Turn the ignition switch to LOCK (0).
8. Remove the jumper wire.
9. Connect ATF temperature sensor connector terminals No. 1 and No. 2 with a jumper wire.
10. Turn the ignition switch to ON (II).
11. Check the ATF temperature sensor voltage with the HDS in the A/T Data List.
Does the ATF Temp Sensor (V) read 0.07 V or below?
YES -
Replace the ATF temperature sensor Service and Repair, then go to step 21.
NO -
Repair an open in the wire between PCM connector terminal C16*1 or B34*2 and the ATF temperature sensor connector terminal No. 1, then go to step 21.
12. Turn the ignition switch to LOCK (0).
13. Jump the SCS line with the HDS.
14. Disconnect PCM connector C (49P).
15. Check for continuity between PCM connector terminal C33 and ATF temperature sensor connector terminal No. 2.
Is there continuity?
YES -
Check for poor connections or loose terminals between the ATF temperature sensor and the PCM. If the connections are OK, go to step 16.
NO -
Repair an open in the wire between PCM connector terminal C33 and the ATF temperature sensor, then go to step 21.
16. Reconnect all connectors.
17. Update the A/T software in the PCM if it does not have the latest software PCM Update, or substitute a known-good PCM.
18. Start the engine in P, and wait for at least 20 seconds.
19. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0713 indicated?
YES -
If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1.
NO -
Go to step 20.
20. Monitor the OBD STATUS for P0713 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other Pending or Confirmed DTCs were indicated in step 19, go to the indicated DTC's troubleshooting.
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between the ATF temperature sensor and the PCM. If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step 18.
21. Reconnect all connectors.
22. Clear the DTC with the HDS.
23. Start the engine in P, and wait for at least 20 seconds.
24. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0713 indicated?
YES -
Check for poor connections or loose terminals between the ATF temperature sensor and the PCM, then go to step 1.
NO -
Go to step 25.
25. Monitor the OBD STATUS for P0713 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 24, go to the indicated DTC's troubleshooting.
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between the ATF temperature sensor and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, go to step 23.