Programming the DeI System

The following information provides a procedure to add new remotes and program the DEI Security System1s various features. It is possible to access and change any of the feature settings using the Valet Switch.

To Add a New Remote:

The keyless entry receiver CPU will learn up to four different remotes. If there are more than four remotes introduced to the system, the transmitters added first will be deleted. (First remote in, first remote out).

NOTE:
The LED (P/N 00265-11001) and the Valet Switch (P/N 00265-11000) are not included in the DEI keyless kit. The two parts are required in order to program and/or add new remotes. The LED and Valet Switch are included with the security upgrade kit and as part of the replacement transmitters.

Make sure to keep an LED and Valet Switch available for use to assist customers to program the keyless kits.

1. Plug the Valet Switch into blue 2-pin port on side of keyless entry receiver (CPU).

2. Plug LED into white 2-pin port on side of keyless entry receiver (CPU).

3. Turn ignition switch to the "on" position.

4. Press and RELEASE Valet Switch seven times.

5. Press and HOLD Valet Switch.

6. LED should respond by flashing seven times.

7. Press button I (lock button) of remote you wish to add.

8. Release Valet button.

9. Turn ignition switch "off".

10. Test each remote for complete function.

Program Features:

NOTE:
This procedure is applicable for security upgrade only.

1. Open the vehicle door.

2. Turn the ignition on, and then off.





3. Select a feature (refer to table shown).

Locate the Valet Switch underneath the driver side dashboard area. Press and release the Valet Switch the number of times (cycles) corresponding to the feature corresponding to the feature you wish to program. For example, to access the Siren Duration feature, press and release the Valet Switch three times. Then press the button once more and HOLD it. The siren will chirp the number of times corresponding to the feature you have accessed.

NOTE:
The default settings are indicated with asterisks. A description of the system features are outlined.

4. Program the feature.





While holding the Valet Switch, you can toggle the feature on and off using your factory remote transmitter. Pressing the button that locks the doors (button I) will select the one-chirp or default setting. Pressing the button that unlocks the doors (button II) will select the two-chirp setting.





5. Release the Valet Switch.

6. Test the system to make sure the feature that you have programmed or selected functions correctly.

NOTE:
Once a feature is programmed, other features can be programmed

To access another feature:

^ Press and release the Valet Switch the number of times necessary to advance from the feature you just programmed to the next one you wish to program. Then press the Valet Switch once more and hold it.

^ For example, if you just programmed the second feature and you would like to program the seventh feature in the menu, you would:

a. Press and release the Valet Switch five times.

b. Press it once more and hold it.

c. The siren would chirp seven times to confirm access to Feature 7.

The Programming procedure will be exited if any of the following occurs:

^ Close the open door

^ Turn the ignition on.

^ No activity for longer than 15 seconds.

^ Press the valet button too many times.

SYSTEM FEATURE DESCRIPTIONS:

* 1 ACTIVE/PASSIVE ARMING: When active arming is selected, the system will only arm when the transmitter is used. When set to passive arming, the system will arm automatically 30 seconds after the last door is closed. To alert the consumer of passive arming, the siren will chirp and the parking lights will flash 30 seconds after the door is closed.

* 2 AUDIBLE ARM/DISARM CONFIRMATION ON/OFF: This feature controls the chirps that confirm the arming and disarming of the system. In the ON setting (default), the siren will provide audible confirmation when arming and disarming the system. If programmed to the OFF position, no siren chirps will be heard when arming or disarming.

* 3 SIREN DURATION 30/60 SECONDS: In the default setting, the full triggered sequence will continue for 30 seconds when triggered. This can be programmed to 60 seconds in the system features learn routine.

* 4 DOOR TRIGGER INSTANT/DELAYED: In the instant (default) setting, if a door is opened while the security system is armed, the system will trigger immediately. In the delayed setting, there is a 15-second delay before the doors will trigger the system. This gives the user 15 seconds to disarm the system after a door is opened without having disarmed with the factory transmitter.

* 5 DOOR TRIGGER ERROR CHIRP ON/OFF: With the door trigger error chirp programmed off, the system will not report an invalid zone on arming when the door trigger wire is active. This eliminates the extra chirps that occur when interfacing with vehicles that have exceptionally long dome light delay circuits.

* 6 NO FUNCTION

* 7 NO FUNCTION

* 8 NO FUNCTION

* 9 VALET PULSE COUNT 1 - 5 PULSES: The system can be programmed to count the number presses of the Valet Switch before disarming the security system. The factory default setting is 1 pulse. The unit can be programmed for 2 - 5 pulses using the unlock button (button II) to select the setting. (See the Valet Mode section below).

* VALET MODE:

In Valet Mode, the system will not arm, even with the transmitter, but all convenience functions (door locks, etc.) will work normally. This is very useful when washing or servicing the vehicle.

To enter or exit Valet Mode with the Valet Switch:

1. Turn ignition to the "on" position. Then turn to the "oft" position.

2. Press and release the Valet Switch within 10 seconds. The status LED will light steady if you entered Valet Mode.

To exit Valet Mode, repeat the steps above. The LED will turn off when exiting Valet Mode.

DEI SYSTEM:





1. Remote transmitter (P/N 00265-11002) for 2001 Sonata and 2001 Tiburon.





2. Valet Switch (P/N 00265-11000).





3. LED (P/N 00265-11001).