P1717

DTC P1717 STEERING WHEEL ANGLE SENSOR 1-INPUT SIGNAL





COMPONENT LOCATION

GENERAL DESCRIPTION
Steering angle sensor is a hall plate between the photo-controller LED and the photo transistor. As the hole plate rotates with steering wheel rotation, electrical signal will be generated depending on whether the LED light passes through the plate to the photo-transistor or not. The signal is the steering wheel operation angular velocity and used to detect the steering wheel turning direction.

DTC DESCRIPTION
The DTC will set when the steering angle sensor #1 signal to 4WD ECM is out of range.





DTC DETECTING CONDITION





SCHEMATIC DIAGRAM





WAVEFORM INSPECTION

TERMINAL & CONNECTOR INSPECTION
1. Many malfunctions in the electrical system may be caused from poor harness and terminals. These faults can be caused by interference from other electrical systems and mechanical or chemical damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
Has a problem been found?
YES Repair as necessary and go to "Verification of Vehicle Repair" procedure.
NO Go to the next procedure,

SIGNAL CIRCUIT INSPECTION
1. Steering angle sensor #1 Signal Inspection
1) IG KEY ON, ENG ON
2) 4WD ECM, Steering angle sensor connector: Connect.
3) Monitor signal waveform between terminal 5 of Steering angle sensor harness connector M14 and chassis ground.
4) Rotate the steering wheel both ways.
Is Steering angle sensor #1 Signal display near the specified value?
YES This may caused by intermittent fault. Verify data changeability by shaking the harness.
NO
^ Inspect power and power supply line of Steering angle sensor #1 circuit.
^ Inspect ground and ground line of Steering angle sensor #1 circuit.
^ Inspect ground to short of Steering angle sensor #1 circuit.
^ Inspect open or short of Steering angle sensor #1 circuit.
^ Check for Steering angle sensor module and replace it as necessary.
^ Check for 4WD ECM and replace it as necessary.
2. Steering angle sensor #1 short to ground Inspection
1) IG KEY OFF, ENG OFF
2) 4WD ECM connector and Steering angle sensor connector: Disconnect.





3) Measure resistance between terminal 5 of Steering angle sensor harness connector M14 and chassis ground.
Specification: Approximately 0 ohms
Is resistance display near the specified value?
YES Proceed next inspection procedure.
NO Repair ground to short circuit of Steering angle sensor #1 circuit.
^ If problem is solved, go to the "Verification of Vehicle Repair"
3. Steering angle sensor #1 open Inspection
1) IG KEY OFF, ENG OFF
2) 4WD ECM connector and Steering angle sensor connector: Disconnect.





3) Measure resistance between terminal 5 of Steering angle sensor harness connector M14 and terminal 23 of 4WD ECM harness connector.
Is resistance display near the specified value?
YES Replace with normal Steering angle sensor module temporarily and check if vehicle run normally. If trouble is disappeared, replace Steering angle sensor control module.
^ Replace with normal 4WD ECM temporarily and check if vehicle run normally. If trouble is disappeared, replace 4WD ECM. If problem is solved, go to the "Verification of Vehicle Repair".
NO Repair open circuit of Steering angle sensor #1 circuit.
If problem is solved, go to the "Verification of Vehicle Repair".

POWER SUPPLY CIRCUIT INSPECTION
1. Steering angle sensor voltage Inspection
1) IG KEY ON, ENG OFF
2) Sensor connector (M14): Disconnect.





3) Measure voltage between terminal 2 of Steering angle sensor harness connector M14 and chassis ground.
Specification Approximately 5V
Is voltage display near the specified value?
YES Proceed next inspection procedure.
NO Inspect open or short of power supply circuit.
^ Check if there is 5V output voltage from 4WD ECM.
^ If problem is solved, go to the "Verification of Vehicle Repair"

GROUND CIRCUIT INSPECTION
1. Ground Circuit Inspection
1) IG KEY OFF, ENG OFF
2) Sensor connector (M14): Disconnect.





3) Measure resistance between terminal 3 of Steering angle sensor harness connector M14 and chassis ground.
Specification: Approximately 1 Ohm below,
Is resistance display near the specified value?
YES Proceed next inspection procedure.
NO Repair open circuit of Steering angle sensor harness.
^ If problem is solved, go to the "Verification of Vehicle Repair".

VERIFICATION OF VEHICLE REPAIR
1. IG KEY ON, ENG ON
2. Steering angle sensor module, 4WD ECM connector: Connect.
3. Clear the DTC with a scan tool.
4. Rotate the steering wheel both ways.
5. Verify the malfunction relevant to steering angle sensor #1.
Does the scan tool display any DTC relevant to steering angle sensor #1?
YES Go to the applicable troubleshooting procedure.
NO System OK.