A/T Does Not Shift: D4 -> D5
A/T Does Not Shift: D4 -> D5SYMPTOM:
^ The vehicle does not shift-up from the D4 to D5 gear at the specified speed.
^ The vehicle does not shift-up from the D4 to D5 gear unless A/T is warmed up.
DIAGNOSTIC PROCEDURE
1. CHECK SYMPTOM Check if vehicle creeps forward in "D" position" and vehicle can be started from D1.
OK or NG
OK >> GO TO 2.
NG >> Refer to AT-206 Vehicle Does Not Creep Forward In D Position. "Vehicle Does Not Creep Forward In "D" Position", AT-208 Vehicle Cannot Be Started From D1. "Vehicle Cannot Be Started From D1".
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT-96, "SELF-DIAGNOSTIC RESULT MODE", AT-107, "Diagnostic Procedure Without CONSULT-II".
Is any malfunction detected by self-diagnostic results?
YES >> Check the malfunctioning system. Refer to "SELF-DIAGNOSTIC RESULT MODE", "Judgement Self-Diagnosis Code".
NO >> GO TO 3.
3. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to "Checking A/T Fluid".
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
4. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to "LINE PRESSURE TEST".
OK or NG
OK >> GO TO 7.
NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.
5. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to "Control Valve with TCM and A/T Fluid Temperature Sensor 2".
2. Disassemble A/T. Refer to "DISASSEMBLY".
3. Check the following.
- Oil pump assembly.
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to "Control Valve with TCM and A/T Fluid Temperature Sensor 2".
2. Disassemble A/T. Refer to "DISASSEMBLY".
3. Check the following.
- Oil pump assembly.
- Power train system. Refer to "DISASSEMBLY".
- Transmission case. Refer to "DISASSEMBLY".
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
7. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to "Control Valve with TCM and A/T Fluid Temperature Sensor 2".
2. Check A/T fluid condition. Refer to "Fluid Condition Check".
OK or NG
OK >> GO TO 8.
NG >> GO TO 11.
8. DETECT MALFUNCTIONING ITEM
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to "Symptom Chart" (Symptom No.13).
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
9. CHECK SYMPTOM
Check again. Refer to "Cruise Test - Part 1".
OK or NG
OK >> INSPECTION END
NG >> GO TO 10.
10. CHECK TCM
1. Check TCM input/output signals. Refer to "TCM Input/Output Signal Reference Values".
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> INSPECTION END
NG >> Repair or replace damaged parts.
11. DETECT MALFUNCTIONING ITEM
^ Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to "Symptom Chart" (Symptom No.13).
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.