Diagnosis Procedure

SELECTOR LEVER POSITION INDICATOR


Description

Indicates selector lever position.




SELECTOR LEVER POSITION INDICATOR


Diagnosis Procedure

1.CHECK MALFUNCTIONING ITEM
Which item is abnormal?
Position indicator lamp- GO TO 2.
Illumination lamp- GO TO 10.
2.CHECK POWER SOURCE
1. Turn ignition switch OFF.
2. Disconnect control device connector.
3. Turn ignition switch ON.
4. Check voltage between control device vehicle side harness connector terminals.





Is the inspection result normal?
YES - GO TO 6.
NO - GO TO 3.
3.CHECK GROUND CIRCUIT
Check continuity between control device vehicle side harness connector terminal and ground.





Is the inspection result normal?
YES - GO TO 4.
NO - Repair or replace damaged parts.
4.CHECK HARNESS BETWEEN CONTROL DEVICE AND BCM (PART 1)
1. Disconnect BCM connector.
2. Check continuity between control device vehicle side harness connector terminal and BCM vehicle side harness connector terminal.





Is the inspection result normal?
YES - GO TO 5.
NO - Repair or replace damaged parts.
5.CHECK HARNESS BETWEEN CONTROL DEVICE AND BCM (PART 2)
Check continuity between control device vehicle side harness connector terminal and ground.





Is the inspection result normal?
YES - Check the following.
- Check terminals of BCM connector and control device harness connector for damage.
- Check connector for loose connection.
NO - Check BCM input/output signal. Refer to Pinout Values and Diagnostic Parameters.
6.CHECK SHIFT POSITION SWITCH
1. Disconnect shift position switch connector.
2. Check continuity between control device harness connector terminals and shift position switch connector terminals.





Is the inspection result normal?
YES - GO TO 7.
NO - Repair or replace damaged parts. Refer to .
7.CHECK HARNESS BETWEEN SHIFT POSITION SWITCH AND SELECTOR LEVER POSITION INDICATOR (PART 1)
1. Disconnect selector lever position indicator connector.
2. Check continuity between shift position switch harness connector terminals and selector lever position indicator connector terminals.





Is the inspection result normal?
YES - GO TO 8.
NO - Repair or replace damaged parts. Refer to .
8.CHECK HARNESS BETWEEN SHIFT POSITION SWITCH AND SELECTOR LEVER POSITION INDICATOR (PART 2)
Check harness cladding between shift position switch connector and selector lever position indicator connector for damage.
Is the inspection result normal?
YES - GO TO 9.
NO - Repair or replace damaged parts. Refer to .
9.CHECK SELECTOR LEVER POSITION INDICATOR
Check selector lever position indicator. Refer to Component Inspection.
Is the inspection result normal?
YES - Check the following.
- Check terminals of control device connector, shift position switch connector and selector lever position indicator connector for damage.
- Check connector for loose connection.
NO - Repair or replace damaged parts. Refer to .
10.CHECK POWER SOURCE
1. Turn ignition switch OFF.
2. Disconnect control device connector.
3. Turn ignition switch ON.
4. Check voltage between control device vehicle side harness connector terminals.





Is the inspection result normal?
YES - GO TO 11.
NO - Check illumination circuit. Refer to Illumination.
11.CHECK SHIFT POSITION SWITCH
1. Disconnect shift position switch connector.
2. Check continuity between control device harness connector terminals and shift position switch connector terminals.





Is the inspection result normal?
YES - GO TO 12.
NO - Repair or replace damaged parts. Refer to .
12.CHECK HARNESS BETWEEN SHIFT POSITION SWITCH AND SELECTOR LEVER POSITION INDICATOR (PART 1)
1. Disconnect selector lever position indicator connector.
2. Check continuity between shift position switch harness connector terminals and selector lever position indicator connector terminals.





Is the inspection result normal?
YES - GO TO 13.
NO - Repair or replace damaged parts. Refer to .
13.CHECK HARNESS BETWEEN SHIFT POSITION SWITCH AND SELECTOR LEVER POSITION INDICATOR (PART 2)
Check harness cladding between shift position switch connector and selector lever position indicator connector for damage.
Is the inspection result normal?
YES - GO TO 9.
NO - Repair or replace damaged parts. Refer to .