P2A03
P2A00, P2A03 A/F SENSOR 1
DTC Logic
DTC DETECTION LOGIC
To judge the malfunction, the A/F signal computed by ECM from the A/F sensor 1 signal is monitored so it will not shift to LEAN side or RICH side.
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE
1.Clear the mixture ratio self-learning value. For USA And Canada.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Turn ignition switch ON.
4.Turn ignition switch OFF and wait at least 10 seconds.
5.Start engine and keep the engine speed between 3,500 and 4,000 rpm for 1 minute under no load.
6.Let engine idle for 1 minute.
7.Keep engine speed between 2,500 and 3,000 rpm for 20 minutes.
8.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Go to .
NO- INSPECTION END
Diagnosis Procedure
1. RETIGHTEN A/F SENSOR 1 AND HEATED OXYGEN SENSOR 2
Loosen and retighten the A/F sensor 1 and heated oxygen sensor 2. Exploded View.
- GO TO 2.
2. CHECK FOR EXHAUST GAS LEAK
1.Start engine and run it at idle.
2.Listen for an exhaust gas leak before the three way catalyst 2.
Is exhaust gas leak detected?
YES- Repair or replace.
NO- GO TO 3.
3. CHECK A/F SENSOR 1 CONNECTOR
1.Disconnect A/F sensor 1 harness connector.
2.Check that water is not inside connectors.
Is the inspection result normal?
YES- GO TO 4.
NO- Repair or replace harness connector.
4. CHECK FOR INTAKE AIR LEAKAGE
1.Reconnect A/F sensor 1 harness connector.
2.Start engine and run it at idle.
3.Listen for an intake air leakage after the mass air flow sensor.
Is intake air leakage detected?
YES- Repair or replace malfunctioning part.
NO- GO TO 5.
5. CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1.Clear the mixture ratio self-learning value. For USA And Canada.
2.Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected? Is it difficult to start engine?
YES- Perform trouble diagnosis for DTC P0171, P0174 or P0172, P0175. For USA And Canada or For USA And Canada.
NO- GO TO 6.
6. CHECK AIR FUEL RATIO SENSOR 1 POWER SUPPLY CIRCUIT
1.Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2.Turn ignition switch ON.
3.Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES- GO TO 7.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
7. CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.
5.Also check harness for short to power.
Is the inspection result normal?
YES- GO TO 8.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
8. CHECK A/F SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.Also check harness for short to power.
Is the inspection result normal?
YES- GO TO 9.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
9. CHECK A/F SENSOR 1 HEATER
For USA And Canada.
Is the inspection result normal?
YES- GO TO 10.
NO- GO TO 12.
10. CHECK HEATED OXYGEN SENSOR 2
Check heated oxygen sensor 2. For USA And Canada.
Is the inspection result normal?
YES- GO TO 11.
NO- Repair or replace malfunctioning part.
11. CHECK INTERMITTENT INCIDENT
Perform Intermittent Incident.
Is the inspection result normal?
YES- GO TO 12.
NO- Repair or replace malfunctioning part.
12. REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Exploded View.
CAUTION:
- Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
- Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant (commercial service tool).
Will CONSULT be used?
YES- GO TO 13.
NO- GO TO 14.
13. CONFIRM A/F ADJUSTMENT DATA
WITH CONSULT
1.Turn ignition switch ON.
2.Select "A/F ADJ-B1" and "A/F ADJ-B2" in "DATA MONITOR" mode with CONSULT.
3.Check that "0.000" is displayed on CONSULT screen.
Is "0.000" displayed?
YES- INSPECTION END
NO- GO TO 14.
14. CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
Clear the mixture ratio self-learning value. For USA And Canada.
Will CONSULT be used?
YES- GO TO 15.
NO- INSPECTION END
15. CONFIRM A/F ADJUSTMENT DATA
WITH CONSULT
1.Turn ignition switch ON.
2.Select "A/F ADJ-B1" and "A/F ADJ-B2" in "DATA MONITOR" mode with CONSULT.
3.Check that "0.000" is displayed on CONSULT screen.
- INSPECTION END