IP Harness Replacement
Instrument Panel (I/P) Harness ReplacementRemoval Procedure
CAUTION: Refer to Battery Disconnect Caution in Cautions and Notices.
1. Disconnect the battery negative cable.
2. Disable the SIR. Refer to SIR Disabling and Enabling Zone 3 and SIR Disabling and Enabling Zone 5 in Restraint Systems.
3. Remove the front seats.
4. Remove the second row seats.
5. Remove the center console.
6. Remove the instrument panel (IP).
7. Fold back the front portion of the rear carpet in order to reveal the IP harness connected to the rear electrical center. Refer to Carpet Replacement - Rear in Interior Trim.
8. Remove the IP harness from the rear electrical center.
9. Disconnect the inline IP harness electrical connectors from the body wiring harness electrical connector.
10. Disconnect the two inline IP wire harness electrical connectors from the body harness.
11. Remove the HVAC support bracket from the IP substrate.
12. Disconnect the park brake electrical connector (2).
13. Disconnect the automatic transmission shift interlock electrical connector (1).
14. Disconnect the sensing diagnostic module (SDM) electrical connectors.
15. Disconnect the 10-way in line electrical connector located near the SDM.
16. Disconnect the 4-way in line electrical connector located near the SDM.
17. Disconnect the electrical connector (3) from the HVAC evaporator blower motor resister pack.
18. Disconnect the electrical connector (2) from the passenger temperature valve.
19. If equipped, release the rosebud that retains the theft deterrent shock sensor to the IP support bracket.
20. Disconnect the SIR electrical connector (1).
21. Remove the splice pack retaining bolt located at the front of the shift lever bracket.
22. Disconnect the electrical connectors (1) from the discharge air temperature sensors.
23. Disconnect the electrical connector (2) from the auxiliary blower motor.
24. Disconnect the electrical connector (2) from the accelerator pedal sensor.
25. Disconnect the electrical connector from the stop lamp switch (1).
26. Remove the connector retaining bolt and disconnect the electrical connector (3) from the steering column.
27. If equipped, disconnect the electrical connector from the clutch pedal switch.
28. Remove the bolts (1) that retain the IP wire harness to the left IP support bracket.
29. Disconnect the electrical connectors (1) from the transfer case shift control module, located near the left side of the steering wheel support bracket.
30. Partially remove the HVAC module assembly in order to gain access to the remaining electrical connectors.
31. Disconnect the electrical connector (1) from the HVAC discharge air temperature sensor.
32. Disconnect the air inlet electrical connector (2) from the HVAC actuator.
33. Disconnect the defroster (4), air conditioning (3), and driver's side temperature valve (2) electrical connectors from the HVAC actuators.
34. Disconnect the discharge air temperature electrical connector (1) from the HVAC actuator.
35. Open the hood.
36. Remove the air inlet grille in order to gain access to the windshield wiper motor.
37. Remove the IP harness retaining clip from the plenum weld stud.
38. Disconnect the IP harness electrical connector (1) from the windshield wiper motor.
39. Disconnect the IP harness inline electrical connector (1) from the forward lamp harness.
40. Disconnect the battery positive cable terminal (2) from the underhood junction block.
41. Disconnect the 2 IP harness two-way electrical connectors (3) from the underhood junction block base.
42. Disconnect the IP harness inline electrical connector from the chassis inline wiring harness.
43. Remove the grounding bolt (2) retaining the ground terminals to the front fender.
44. Remove the grounding nut (1) retaining the ground terminals to the weld stud located on the front plenum.
45. Disconnect the IP harness electrical connector (2) from the powertrain control module.
46. Disconnect the IP harness inline electrical connector (1) from the engine harness inline electrical connector.
47. Remove the IP harness grommet from the bulkhead.
48. Pass the exterior portion of the IP harness through the bulkhead.
49. Remove the IP harness from the vehicle.
Installation Procedure
1. Position the IP harness to the vehicle.
2. Pass the exterior portion of the IP harness through the bulkhead.
3. Install the IP harness grommet to the bulkhead.
4. Connect the IP harness inline electrical connector (1) to the engine harness inline electrical connector.
5. Connect the IP harness electrical connector (2) to the powertrain control module.
NOTE: Refer to Fastener Notice in Cautions and Notices.
6. Install the grounding nut (1) that retains the ground terminals to the weld stud located on the front plenum.
Tighten: Tighten the nut to 10 Nm (88 lb in).
7. Install the grounding bolt (2) that retains the ground terminals to the front fender.
8. Connect the IP harness inline electrical connector to the chassis inline wiring harness.
9. Connect the 2 two-way IP harness electrical connectors (3) to the underhood junction block base.
10. Connect the battery positive cable terminal (2) to the underhood junction block.
11. Install the battery cable terminal nut.
Tighten: Tighten the nut to 10 Nm (88 lb in).
12. Connect the IP harness in line electrical connector (1) to the forward lamp harness.
13. Connect the IP harness electrical connector (1) to the windshield wiper motor.
14. Install the IP harness retaining clip to the plenum weld stud.
15. Install the air inlet grille.
16. Close the hood.
17. Install the HVAC module assembly to the vehicle.
18. Connect the discharge air temperature electrical connector (1) to the HVAC actuator.
19. Connect the defroster (4), air conditioning (3), and drivers side temperature valve (2) electrical connectors to the HVAC actuators.
20. Connect the air inlet electrical connector to the HVAC actuator.
21. Connect the electrical connector (1) to the HVAC discharge air temperature sensor.
22. Connect the electrical connectors (2) to the transfer case shift control module, located near the left side of the steering wheel support bracket.
23. Install the bolts (1) that retain the IP wire harness to the IP support bracket.
Tighten: Tighten the bolts to 2.5 Nm (22 lb in).
24. If equipped, connect the electrical connector to the clutch pedal switch.
25. Connect the electrical connector (3) to the steering column.
26. Install the steering column electrical connector bolt.
Tighten: Tighten the bolt to 6 Nm (53 lb in).
27. Connect the electrical connector to the stop lamp switch (1).
28. Connect the electrical connector (2) to the accelerator pedal sensor.
29. Connect the electrical connector (2) to the floor auxiliary blower motor.
30. Connect the electrical connectors (1) to the discharge air temperature sensors.
31. Install the splice pack and retaining bolt located at the front of the shift lever bracket.
Tighten: Tighten the bolt to 10 Nm (88 lb in).
32. Connect the 4-way in line electrical connector located near the SDM.
33. Connect the 10-way in line electrical connector located near the SDM.
34. Connect the SDM electrical connectors.
35. Connect the park brake electrical connector (2).
36. Connect the automatic transmission shift interlock electrical connector (1).
37. Connect the SIR electrical connector (1),
38. Attach the rosebud that retains the theft deterrent shock sensor to the IP support bracket, if equipped.
39. Connect the electrical connector (2) to the passenger temperature valve.
40. Connect the electrical connector (3) to the HVAC evaporator blower motor resister pack.
41. Install the HVAC support bracket to the IP substrate.
42. Connect the inline body electrical connector from the body wiring harness electrical connector.
43. Connect the two inline IP wire harness electrical connectors to the body harness.
44. Pass the IP wire harnesses through the rear carpet in order to install the IP harness to the rear electrical center.
45. Install the rear carpet.
46. Install the IP harness to the rear electrical center.
47. Install the IP.
48. Install the center console.
49. lnstall the second row seats.
50. Install the front seats.
51. Enable the SIR. Refer to SIR Disabling and Enabling Zone 3 and SIR Disabling and Enabling Zone 5 in Restraint Systems.
52. Connect the negative battery cable.