Tie Rod: Service and Repair
Tie Rod Replacement- InnerTools Required
J 34028 Inner Tie Rod Wrench
Disassembly Procedure
1. To remove the rack and pinion boot and the breather tube.
2. Place the gear in a vise.
Notice: Do not change the steering gear preload adjustment before moving the inner he rod from the steering gear. Changing the steering gear preload adjustment before moving the inner tie rod could result in damage to the pinion and the steering gear.
3. Remove the shock dampener (4) from the inner tie rod housing (6).
4. Slide the shock dampener (4) back on the rack (5).
Notice: Refer to Pipe Wrench Positioning Notice in Service Precautions.
5. Place a pipe wrench on the rack (5) next to the inner tie rod housing (6).
6. Place a wrench on the flats of the inner tie rod housing (6).
7. Rotate the inner tie rod housing (6) counterclockwise, while holding the rack stationary, until the inner tie rod separates from the rack (5).
Notice: Do not change the steering gear preload adjustment before moving the inner he rod from the steering gear. Changing the steering gear preload adjustment before moving the inner tie rod could result in damage to the pinion and the steering gear.
8. Remove the shock dampener (3) from the inner tie rod housing (2).
9. Slide the shock dampener (3) back on the rack (5).
Notice: Refer to Pipe Wrench Positioning Notice in Service Precautions.
10. Place a pipe wrench on the rack.
11. Place a wrench on the flats of the inner tie rod housing (2).
12. Rotate the inner tie rod housing (2) counterclockwise, while holding the rack stationary, until the inner tie rod (1) separates from the rack (5).
13. If female rack (1) and male inner tie rod (3), remove the old LOCTITE(-) from the threads (2) of the inner tie rod and the rack. If male rack (5) and female inner tie rod (4) LOCTITE(-) will not be present.
Assembly Procedure
1. Slide the shock dampener (4) forward onto the rack (3).
Important: Threads must be clean prior to LOCTITE application. Check LOCTITE, or equivalent, container for expiration date. Use only enough LOCTITE to evenly coat threads. If male rack (3) and female inner tie rod (2) do not apply LOCTITE.
2. If female rack (3) and male inner tie rod (2), apply LOCTITE 262, or equivalent, to the inner tie rod threads.
3. Attach the inner tie rod onto the rack (3).
Notice: Refer to Pipe Wrench Positioning Notice in Service Precautions.
4. Place a pipe wrench on the rack (3) next to the inner tie rod housing (2).
Notice: Refer to Fastener Notice in Service Precautions.
5. Place a torque wrench and J 34028 on the flats of the inner tie rod housing (2).
^ Tighten the inner tie rod to 100 Nm (74 ft. lbs.).
6. Slide the shock dampener (2) forward onto the rack.
Important: Threads must be clean prior to LOCTITE application. Check LOCTITE, or equivalent, container for expiration date. Use only enough LOCTITE to evenly coat threads. If male rack and female inner tie rod (1) do not apply LOCTITE.
7. If female rack and male inner tie rod (1), apply LOCTITE 262, or equivalent, to the inner tie rod threads.
8. Attach the inner tie rod (1) onto the rack.
Notice: Refer to Pipe Wrench Positioning Notice in Service Precautions.
9. Place a pipe wrench on the rack next to the inner tie rod housing (4).
10. Place a torque wrench and J 34028 on the flats of the inner tie rod housing (7).
^ Tighten the inner tie rod to 100 Nm (74 ft. lbs.).
11. Place the inner tie rod assembly (2) in a vise.
Important: If female rack (1) and male inner tie rod (2) do not stake. If male rack (1) and female inner he rod (2) you must stake.
12. Stake both sides of the female inner tie rod assembly housing to the male rack.
13. Insert a 0.010 inch gage (1) between the rack (2) and the inner tie rod housing in order to check both stakes. The feeler (1) must not pass between the rack and the housing stake.
14. Slide the shock dampener (2) over the inner tie rod housing (3) until the front lip of the shock dampener (2) bottoms against the inner tie rod housing (3).
15. To assemble the rack and pinion boot and the breather tube.