C1032
C1032-RIGHT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE
For a complete wiring diagram, refer to the Wiring Information.
- When Monitored:
With the ignition on.
- Set Condition:
When the Right Rear Wheel Speed Sensor (WSS) Signal is intermittently missing while vehicle speed is above 40 km/h (25 mph) or erratic wheel speed signal during acceleration or sensed wheel speed is different from other wheels.
1. CHECK FOR DTC C1032-RIGHT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE
NOTE: This DTC must be active for the results of this test to be valid.
1. Turn the ignition on.
2. With the scan tool, record and erase DTCs.
CAUTION: Make sure brake capability is available before road testing.
3. Road test the vehicle over 40 km/h (25 mph).
NOTE: Vehicle must be driven above 40 km/h (25 mph) for set conditions to be met.
4. With the scan tool, read DTCs.
Does the scan tool display: C1032-RIGHT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE active?
Yes
- Go To 3
No
- Go To 2
2. CHECK WHEEL SPEED SENSOR SIGNALS
1. Turn the ignition on.
2. With the scan tool, monitor and graph ALL the WSS speeds and compare graph while an assistant drives the vehicle.
NOTE: If graph shows periodic dropouts pay close attention to the tone wheel.
3. Slowly accelerate as straight as possible from a stop to 40 km/h (25 mph).
Is the Right Rear WSS speed showing 0 km/h (0 mph) or not matching other wheels or showing erratic behavior?
Yes
- Go To 3
No
- Perform the ABS-INTERMITTENT CONDITION diagnostic procedure. ABS Intermittent Condition Test.
3. CHECK FOR IMPROPER RIGHT REAR TIRE PRESSURE/MISMATCHED TIRES
1. Turn the ignition off.
2. Check and adjust the Right Rear Tire pressure.
3. Check and adjust all other tire pressures.
4. Inspect for mismatched tires on vehicle.
Is the Right Rear Tire improperly inflated or mismatched tires on vehicle?
Yes
- Repair as necessary.
- Perform ABS VERIFICATION TEST. ABS Verification Test.
No
- Go To 4
4. CHECK AXLE SHAFT FASTENER HARDWARE FOR LOOSENESS
1. Inspect the axle shaft fastener for looseness, and not properly fastened. Tighten fastener to proper specification as required.
Was the Axle Shaft fastener loose?
Yes
- Repair as necessary.
No
- Go To 5
5. CHECK RIGHT REAR WSS LOOSENESS, INSPECT B1, B2 CIRCUITS/TERMINALS FOR DAMAGE
NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals.
1. Inspect the Anti-Lock Brake Module harness connector, Right Rear WSS, and Right Rear WSS harness connector.
2. Inspect the Right Rear WSS for looseness, excessive corrosion and not properly fastened.
3. Inspect the (B1) Right Rear WSS Signal and (B2) Right Rear WSS Supply circuits between the Right Rear WSS and Anti-Lock Brake Module for damage.
Is the Right Rear WSS loose or any of the wiring/connectors/terminals damaged?
Yes
- Repair as necessary.
- Perform ABS VERIFICATION TEST. ABS Verification Test.
No
- Go To 6
6. CHECK RIGHT REAR WHEEL SPEED SENSOR FOR DAMAGE
1. Remove the Right Rear Wheel Speed Sensor.
2. Inspect the Right Rear Wheel Speed Sensor face for damage.
Is the Right Rear Wheel Speed Sensor damaged?
Yes
- Replace sensor and hub assembly.
- Perform ABS VERIFICATION TEST. ABS Verification Test.
No
- Go To 7
7. CHECK RIGHT REAR TONE WHEEL FOR DAMAGE
1. Inspect the Right Rear Tone Wheel for damage, missing teeth, cracks, corrosion or looseness.
NOTE: The Tone Wheel teeth should be perfectly square, not bent, or nicked.
Is the Right Rear Tone Wheel damaged?
Yes
- Repair as necessary.
- Perform ABS VERIFICATION TEST. ABS Verification Test.
No
- Go To 8
8. CHECK RIGHT REAR WHEEL BEARING FOR DAMAGE
1. Inspect the Right Rear wheel bearing for excessive runout or clearance.
NOTE: Refer to the appropriate service information, if necessary, for procedures or specifications.
Is the Right Rear Wheel Bearing Damaged?
Yes
- Repair as necessary.
- Perform ABS VERIFICATION TEST. ABS Verification Test.
No
- Go To 9
9. RIGHT REAR WHEEL SPEED SENSOR
1. Replace the Right Rear Wheel Speed Sensor.
2. Perform ABS VERIFICATION TEST. ABS Verification Test.
3. Road test the vehicle over 40 km/h (25 mph).
NOTE: Vehicle must be driven above 40 km/h (25 mph) for set conditions to be met.
4. With the scan tool, read ABS DTCs.
Did DTC C1032-RIGHT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE reset?
Yes
- Replace the Anti-Lock Brakes Module.
- Perform ABS VERIFICATION TEST. ABS Verification Test.
No
- Test Complete.