Exterior Lighting

LAMPS/LIGHTING - EXTERIOR

WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.

WARNING: To avoid serious or fatal injury when working on the High Intensity Discharge (HID) headlamp system, be certain to take the proper precautions. The headlamp switch must be in the OFF position. Disconnect and isolate the battery negative cable. There is a risk of death caused by contact with high voltage used in the HID headlamps. There is a risk of explosion or fire caused by highly flammable materials in the vicinity of damaged HID lighting elements. There is a risk of injury caused by exposure to Ultra Violet (UV) light, a risk of burns caused by high component operating temperatures, a risk of mercury poisoning through glass splinters produced by bursting HID lighting elements. There is also a risk of poisoning caused by inhalation of mercury vapors and by toxic salts and mercury compounds being ingested or coming into contact with the skin. Do not come into contact with parts that are under high voltage. Persons with active electronic implants (e.g. heart pacemakers) must never work on HID headlamps. Wear insulated safety shoes, safety glasses and protective gloves. Remove flammable materials and ensure sufficient ventilation in the working area.

NOTE: When diagnosing the exterior lighting circuits, remember that high generator output can burn out bulbs rapidly and repeatedly; and, that dim or flickering bulbs can be caused by low generator output or poor battery condition. If one of these symptoms is a problem on the vehicle, be certain to diagnose the battery and charging system, then repair as necessary.

NOTE: A good ground is necessary for proper lighting operation. If a lighting problem is being diagnosed that involves multiple symptoms, systems, or components, the problem can often be traced to a loose, corroded, or open ground.

The lamps and the hard wired circuits between components related to the exterior lighting system may be diagnosed using conventional diagnostic tools and procedures. Refer to the appropriate wiring information. The wiring information includes wiring diagrams, proper wire and connector repair procedures, details of wire harness routing and retention, connector pin-out information and location views for the various wire harness connectors, splices and grounds.

However, conventional diagnostic methods will not prove conclusive in the diagnosis of the exterior lighting system or the electronic controls or communication between modules and other devices that provide some features of the exterior lighting system. The most reliable, efficient, and accurate means to diagnose the exterior lighting system or the electronic controls and communication related to exterior lighting system operation requires the use of a diagnostic scan tool. Refer to the appropriate diagnostic information.

BACKUP LAMPS





BRAKE LAMPS

NOTE: The Center High Mounted Stop Lamp (CHMSL) is illuminated by several Light-Emitting Diode (LED) units that are soldered to the electronic circuit board within the lamp housing. If the brake lamps and all of the LED units within the CHMSL fail to operate, diagnose and repair the brake lamps before attempting to repair the CHMSL. If the brake lamps operate but none of the CHMSL LED units illuminate, test and repair the CHMSL ground or feed circuit if required. If some of the CHMSL LED units operate and some do not, the CHMSL assembly must be replaced with a new unit.






DAYTIME RUNNING LAMPS

NOTE: Before performing the following tests, determine whether the headlamp low and high beams operate. If the headlamp low and high beams are also ineffective, diagnose and repair that problem before attempting to repair the Daytime Running Lamps (DRL).






FRONT FOG LAMPS

NOTE: In addition to the front fog lamp units, the vehicle must have the appropriate left multi-function switch installed. Also, the Front Control Module (FCM) must be properly configured for the front fog lamps option using a diagnostic scan tool. Refer to the appropriate diagnostic information.






HAZARD WARNING LAMPS

NOTE: The hazard switch is integral to the upper instrument panel switch pod, which provides a hard wired output to the FCM. Before performing any of the following tests, confirm whether the left and right turn signals operate satisfactorily. Then determine whether the other functions of the upper instrument panel switch pod are operational. If the turn signals are ineffective or operate improperly, or if the other instrument panel switch pod functions are ineffective, diagnose and repair those problems before attempting to repair the hazard warning lamps system.






HEADLAMPS

NOTE: As part of the exterior lighting failsafe feature, upon ignition ON, all exterior park lamps and the headlamp low beams will illuminate regardless of the left multi-function switch control knob position if the SCM cannot detect an input from the left multi-function switch, or if there is a loss of communication between the left multi-function switch/SCM and the EMIC, between the EMIC and the FCM, or if there is a loss of data bus communication. Diagnose and repair those problems before attempting to repair the headlamp system. The FCM will store a Diagnostic Trouble Code (DTC) for an open or shorted headlamp circuit. In addition, for automatic headlamps, the vehicle must have the appropriate left multi-function switch installed and the FCM must be properly configured for the automatic headlamps option using a diagnostic scan tool. Refer to the appropriate diagnostic information.






HEADLAMP LEVELING (AUTOMATIC)

NOTE: Before performing any of the following tests, confirm whether the park lamps operate satisfactorily. If the park lamps are ineffective or operate improperly, diagnose and repair that problem before attempting to repair the automatic headlamp leveling function.






HEADLAMP LEVELING (MANUAL)

NOTE: Before performing any of the following tests, confirm whether the park lamps operate satisfactorily. If the park lamps are ineffective or operate improperly, diagnose and repair that problem before attempting to repair the manual headlamp leveling function.






PARK LAMPS

NOTE: As part of the exterior lighting failsafe feature, upon ignition ON, all exterior park lamps and the headlamp low beams will illuminate regardless of the left multi-function switch control knob position if the SCM cannot detect an input from the left multi-function switch, or if there is a loss of communication between the left multi-function switch/SCM and the EMIC or between the EMIC and the FCM. Diagnose and repair those problems before attempting to repair the park lamps system.






REAR FOG LAMPS

NOTE: The rear fog lamp switch is integral to the left multi-function switch/SCM, which communicates with the EMIC/CCN over the LIN data bus. Before performing any of the following tests, determine whether the other functions of the left multi-function switch/SCM are operational. If the other left multi-function switch/SCM functions are ineffective, diagnose and repair that problem before attempting to repair the rear fog lamps system.






SMART BEAM(R)

NOTE: For Smart Beam(R) to operate, the vehicle must have the appropriate left multi-function switch installed and the Auto High Beam option must be enabled using the customer programmable features function of the Electronic Vehicle Information Center (EVIC). Also, the Front Control Module (FCM) must be properly configured for the automatic headlamps option using a diagnostic scan tool. Refer to the appropriate diagnostic information.






TURN SIGNAL LAMPS