B1D7F
B1D7F-SEAT FRONT VERTICAL MOTOR CONTROL CIRCUIT PERFORMANCE
For a complete wiring diagram, refer to the wiring information Electrical Diagrams.
- When Monitored:
Whenever the Seat Motor is activated.
- Set Condition:
If the Memory Seat Module does not detect the rotation of the Seat Motor this DTC will set.
1. CHECK FOR RELATED DIAGNOSTIC TROUBLE CODES
1. Turn the ignition on.
2. With the scan tool, read DTC's.
Does the scan tool display any seat position sensor DTC's?
Yes
- Diagnose and repair the other DTC(s) first. Testing and Inspection.
No
- Go To 2
2. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, erase all DTC's.
3. Move the Driver Seat Switch in the Front Vertical up and down position three times.
4. With the scan tool, read DTC's.
Does the scan tool display this DTC?
Yes
- Go To 3
No
- The condition that caused this symptom is currently not present. Check for an intermittent condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or contaminated terminals. Repair as necessary.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
3. CHECK THE (G404) DRIVER SEAT FRONT VERTICAL POSITION SENSE CIRCUIT VOLTAGE
1. Turn the ignition off.
2. Disconnect the Driver Front Vertical Seat Adjuster Motor harness connector.
3. Turn the ignition on.
4. Measure the voltage between the (G404) Driver Seat Front Vertical Position Sense circuit and the (G494) Driver Seat Front Vertical Sensor Ground circuit at the Driver Front Vertical Seat Adjuster Motor harness connector.
Is the voltage above 10.0 volts?
Yes
- Go To 4
No
- Go To 5
4. CHECK THE DRIVER SEAT FRONT VERTICAL UP/DOWN DRIVER CIRCUIT VOLTAGE
1. Using a 12-volt test light connect one lead to the (P119) Driver Seat Front Vertical Up Driver circuit and the other lead to (P121) Driver Seat Front Vertical Down Driver circuit at the Driver Front Vertical Seat Adjuster Motor harness connector.
2. Move the Driver Seat Switch in the Front Vertical up and down position.
Does the test light illuminate with the seat switch engaged in both positions?
Yes
- Replace the track/Front Vertical motor assembly.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
No
- Go To 7
5. CHECK THE (G404) DRIVER SEAT FRONT VERTICAL POSITION SENSE CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Disconnect the Memory Seat Module C2 harness connector.
3. Measure the resistance of the (G404) Driver Seat Front Vertical Position Sense circuit between the Driver Front Vertical Seat Adjuster Motor harness connector and the Memory Seat Module C2 harness connector.
Is the resistance below 10.0 ohms?
Yes
- Go To 6
No
- Repair the (G404) Driver Seat Front Vertical Position Sense circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
6. CHECK THE (G494) DRIVER SEAT FRONT VERTICAL SENSOR GROUND CIRCUIT FOR AN OPEN
1. Measure the resistance of the (G494) Driver Seat Front Vertical Sensor Ground circuit between the Driver Front Vertical Seat Adjuster Motor connector and the Memory Seat Module C2 harness connector.
Is the resistance below 10.0 ohms?
Yes
- Replace the Memory Seat Module.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
No
- Repair the (G494) Driver Seat Front Vertical Sensor Ground circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
7. CHECK THE (P119) DRIVER SEAT FRONT VERTICAL UP DRIVER CIRCUIT FOR AN OPEN
1. Disconnect the Memory Seat Module C2 harness connector.
2. Measure the resistance of the (P119) Driver Seat Front Vertical Up Driver circuit between the Driver Front Vertical Seat Adjuster Motor harness connector to the Memory Seat Module C2 harness connector.
Is the resistance below 10.0 ohms?
Yes
- Go To 8
No
- Repair the (P119) Driver Seat Front Vertical Up Driver circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
8. CHECK THE (P121) DRIVER SEAT FRONT VERTICAL DOWN DRIVER CIRCUIT FOR AN OPEN
1. Measure the resistance of the (P121) Driver Seat Front Vertical Down Driver circuit between the Driver Front Vertical Seat Adjuster Motor harness connector and the Memory Seat Module C2 harness connector.
Is the resistance below 10.0 ohms?
Yes
- Replace the Memory Seat Module.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.
No
- Repair the (P121) Driver Seat Front Vertical Down Driver circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. Power Seat System Verification Test.