B1C4E

B1C4E-1ST ROW PASSENGER SEAT BELT BUCKLE PRETENSIONER CIRCUIT OPEN

Special Tools:










For a complete wiring diagram, refer to the Wiring Information.

- When Monitored:
With the ignition on, the Occupant Restraint Controller (ORC) monitors the resistance of the Passenger Seat Belt Buckle Tensioner circuits.

- Set Condition:
The ORC has detected an open or high resistance on the Passenger Seat Belt Buckle Tensioner circuits.





1. VERIFY ACTIVE DTC

NOTE: Make sure the battery is fully charged.

NOTE: The scan tool, SRS Load Tool Kit , and DVOM are required to perform the following test.

1. With the scan tool, read the ORC DTCs.

Does the scan tool display B1C4E-1ST ROW PASSENGER SEAT BELT BUCKLE PRETENSIONER CIRCUIT OPEN DTC?

Yes

- Go To 2

No

- Perform the AIRBAG SYSTEM INTERMITTENT TEST. . Airbag System Intermittent Condition Test

2. CHECK FOR OPEN PASSENGER SEAT BELT BUCKLE TENSIONER





WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Disconnect the Passenger Seat Belt Buckle Tensioner connector.

NOTE: Check the connectors - Clean and repair as necessary.

2. Connect the SRS Load Tool Kit and SRS Load Tool Jumper to the Passenger Seat Belt Buckle Tensioner connector.

WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

3. With the scan tool, read the ORC DTCs.

Does the scan tool display B1C4E-1ST ROW PASSENGER SEAT BELT BUCKLE PRETENSIONER CIRCUIT OPEN DTC?

Yes

- Go To 3

No

- Replace the Passenger Seat Belt Buckle Tensioner.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.

3. CHECK (R272) PASSENGER SEAT BELT BUCKLE TENSIONER LINE 1 CIRCUIT FOR AN OPEN





WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Disconnect the SRS Load Tool Kit and Jumper from the Passenger Seat Belt Buckle Tensioner connector.
2. Disconnect the ORC connectors.

NOTE: Check the connectors - Clean and repair as necessary.

3. Connect the SRS Load Tool Adaptor to the ORC connectors.
4. Measure the resistance of the (R56) Passenger Seat Belt Buckle Tensioner Line 1 circuit between the Passenger Seat Belt Buckle Tensioner connector cavity 2 and the SRS Load Tool Adaptor cavity C2-4.

Is the resistance below 1.0 Ohm?

Yes

- Go To 4

No

- Repair the (R56) Passenger Seat Belt Buckle Tensioner Line 1 circuit for and open.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.

4. CHECK (R274) PASSENGER SEAT BELT BUCKLE TENSIONER LINE 2 CIRCUIT FOR AN OPEN




1. Measure the resistance of the (R54) Passenger Seat Belt Buckle Tensioner Line 2 circuit between the Passenger Seat Belt Buckle Tensioner connector cavity 1 and the SRS Load Tool Adaptor cavity C2-3.

Is the resistance below 1.0 Ohm?

Yes

- WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to follow these instructions may result in possible serious or fatal injury.

- Replace the ORC.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.

No

- Repair the (R54) Passenger Seat Belt Buckle Tensioner Line 2 circuit for and open.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.