Vehicle Damage Warnings
JACKINGThe following instructions must be carried out before raising the vehicle off the ground.
1. Use a solid level ground surface.
2. Apply parking brake.
3. Select 'P' or 1st gear in main gearbox.
4. Select Low range in transfer gearbox.
CAUTION: To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.
DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS.
Body structure
Air suspension pipes
Bumpers
Fuel lines
Brake lines
Front radius arms
Panhard rod
Steering linkage
Rear Trailing links
Fuel tank
Engine sump
Gearbox bell housing
CAUTION: If supporting vehicle by the front crossmember, the safety stands must be positioned carefully to avoid damage to air suspension pipes.
Vehicle jack
The jack provided with the vehicle is only intended to be used in an emergency, for changing a wheel. Do NOT use the jack for any other purpose. Refer to Owner's Manual for vehicle jack location points and procedure. Never work under a vehicle supported by the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500kg, 3,300 lbs load capacity must be used.
CAUTION: Do not commence work on the underside of the vehicle until suitable axle stands have been positioned under the axle.
Raise the front of the vehicle
1. Position cup of hydraulic arm under differential casing.
NOTE: The differential casing is not central to the axle. Care should be taken when raising the front road wheels off the ground as the rear axle has less sway stiffness.
2. Raise front road wheels to enable an axle stand to be installed under left hand axle tube.
3. Position an axle stand under right hand axle tube, carefully lower jack until axle sits securely on both axle stands, remove trolley jack.
4. Before commencing work on underside of vehicle re-check security of vehicle on stands.
5. Reverse procedure when removing vehicle from stands.
Raise rear of vehicle
1. Position cup of hydraulic arm under differential casing.
2. Raise vehicle to enable axle stands to be installed under left and right hand axle tubes.
3. Lower jack until axle sits securely on axle stands, remove trolley jack.
4. Before commencing work on underside of vehicle re-check security of vehicle on stands.
5. Reverse procedure when removing vehicle from stands.
HYDRAULIC VEHICLE RAMP (FOUR POST)
Use only a 'drive on' type ramp which supports vehicle by its own road wheels. If a 'wheel-free' condition is required, use a 'drive on' ramp incorporating a 'wheel-free' system that supports under axle casings. Alternatively, place vehicle on a firm, flat floor and support on axle stands.
TWO POST VEHICLE RAMPS
The manufacturer of RANGE ROVER VEHICLES DOES NOT recommend using 'Two Post' ramps that employ four adjustable support arms. These are NOT considered safe for Range Rover vehicles.
If a vehicle is installed on a Two Post ramp, responsibility for safety of the vehicle and personnel performing service operations is attributable to the Service Provider.
DYNAMOMETER TESTING - VEHICLES WITH ANTI-LOCK BRAKES (ABS)
WARNING: Do not attempt to test ABS function on a dynamometer
Four wheel dynamometers
NOTE: Before testing a vehicle on a four wheel dynamometer disconnect the valve relay. See Electrical Trouble Shooting Manual. The ABS function will not work, the ABS warning light will illuminate. Normal braking will be available.
Provided that front and rear rollers are rotating at identical speeds and that normal workshop safety standards are applied, there is no speed restriction during testing except any that may apply to the tyres.
Two wheel dynamometers
IMPORTANT: Use a four wheel dynamometer for brake testing if possible.
NOTE: ABS will not function on a two wheel dynamometer. The ABS light will illuminate during testing. Normal braking will be available.
If brake testing on a single rig is necessary it must be carried out with propeller shaft to the rear axle removed, AND neutral selected in BOTH main and transfer boxes.
If checking engine performance, the transfer box must be in high range and drive shaft to stationary axle removed.
WARNING: Vehicles from 99 MY are fitted with 4 wheel traction control, which must be disabled prior to testing on a single axle dynamometer.