Headliner: Service and Repair
REMOVAL1. REMOVE REAR NO. 2 SEAT
2. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT: Tape the screwdriver tip before use.
3. REMOVE REAR MAT SET PLATE
a. Remove the 5 screws.
b. Using a screwdriver, remove the rear mat set plate.
HINT: Tape the screwdriver tip before use.
4. REMOVE NO. 3 REAR SEAT PROTECTORS
a. Remove the screw.
b. Remove the No. 3 rear seat protector.
5. REMOVE NO. 3 SEAT FRONT BRACKET COVERS
a. Remove the screw.
b. Remove the No. 3 seat front bracket cover.
6. REMOVE NO. 3 SEAT BRACKET SUPPORT COVERS
7. REMOVE 3 CRS TETHER ANCHOR BRACKETS
a. Remove the 3 CRS tether anchor bracket covers.
b. Remove the 3 CRS tether anchor brackets.
Torque: 26 N.m (270 kgf.cm, 20 ft.lbf)
8. REMOVE REAR FLOOR CARPET
9. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR ANCHORS
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
10. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR ANCHORS
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
11. REMOVE REAR DOOR SCUFF PLATES
12. REMOVE REAR DOOR OPENING TRIMS
13. REMOVE LH QUARTER TRIM PANEL
a. Remove the quarter trim jack cover.
b. Using a clip remover, remove the 2 clips.
c. Remove the LH quarter trim panel, then disconnect the connector.
14. REMOVE RH QUARTER TRIM PANEL
a. Using a clip remover, remove the clip.
b. Remove the RH quarter trim panel.
15. REMOVE REAR NO. 2 SEAT OUTER BELT SHOULDER ANCHORS
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
16. REMOVE REAR NO. 1 SEAT OUTER BELT HOLDER ANCHORS
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
17. REMOVE UPPER ROOF SIDE INNER GARNISH
a. Using a screwdriver, remove the assist grip plugs, then remove the 4 screws and assist grips.
HINT: Tape the screwdriver tip before use.
b. Using a screwdriver, remove the upper roof side inner garnishes.
HINT: Tape the screwdriver tip before use.
18. REMOVE FRONT DOOR SCUFF PLATES
19. REMOVE COWL SIDE TRIMS
20. FRONT DOOR OPENING TRIMS
21. REMOVE FRONT PILLAR GARNISH
a. Using a screwdriver, remove the assist grip plugs, then remove the 6 screws and 3 assist grips.
HINT: Tape the screwdriver tip before use.
b. Using a screwdriver, remove the front pillar garnishes.
HINT: Tape the screwdriver tip before use.
22. REMOVE CENTER PILLAR LOWER GARNISH
a. Using a screwdriver, remove the seat belt floor anchor cover caps.
HINT: Tape the screwdriver tip before use.
b. Remove the bolts and front seat outer belt floor anchors.
c. Using a screwdriver, remove the center pillar lower garnishes as shown in the illustration.
HINT: Tape the screwdriver tip before use.
23. REMOVE CENTER PILLAR UPPER GARNISH
a. Using a screwdriver, remove the seat belt anchor cover caps.
HINT: Tape the screwdriver tip before use.
b. Remove the bolts and front seat outer belt shoulder anchors.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
c. Using a screwdriver, remove the 8 assist grip plugs, then remove the 8 screws and 4 assist grips.
HINT: Tape the screwdriver tip before use.
d. Using a clip remover, remove the clips.
e. Using a screwdriver, remove the center pillar upper garnishes.
HINT: Tape the screwdriver tip before use.
24. REMOVE SUN VISORS
25. REMOVE DOUBLE VISORS
26. REMOVE HOLDERS
27. REMOVE REAR COOLER CONTROL ASSEMBLY
28. REMOVE REAR TEMPERATURE GAUGE
29. REMOVE DOME LIGHT
a. Using a screwdriver, remove the lens as shown in the illustration.
HINT: Tape the screwdriver tip before use.
b. Remove the 4 screws and dome light, then disconnect the connector.
30. REMOVE MAP LIGHT
a. Using a screwdriver, remove the lens as shown in the illustration.
HINT: Tape the screwdriver tip before use.
b. Remove the 4 screws and map light, then disconnect the connector.
31. REMOVE OVERHEAD CONSOLE BOX
a. Remove the bolt.
b. Using a screwdriver, remove the overhead console box, then disconnect the connector.
HINT: Tape the screwdriver tip before use.
32. REMOVE SLIDING ROOF OPENING TRIM
33. REMOVE ROOF HEADLINING
Using a clip remover, remove the 5 clips and roof headlining.
INSTALLATION
Installation is in the reverse order of removal.