Transmission Installation
INSTALLATION1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
a. Install the torque converter clutch to the automatic transaxle.
b. Using vernier calipers and a straight edge, measure the dimension "A" between the transaxle fitting part of the engine and the converter fitting part of the drive plate (*1).
c. Using vernier calipers and a straight edge, measure the dimension "B" shown in the illustration and check that "B" is greater than "A" (measured in step (*1)).
Standard: A + 1 mm (0.03937 inch) or more
NOTICE: Remember to minus the thickness of the straight edge.
2. INSTALL TRANSFER ASSEMBLY
3. INSTALL AUTOMATIC TRANSMISSION W/TRANSFER
a. Install the automatic transaxle w/transfer with the 8 bolts to the engine.
Torque:
Bolt A 64 Nm (650 kgf-cm, 47 ft. lbs.)
Bolt B 46 Nm (470 kgf-cm, 34 ft. lbs.)
Bolt C 37 Nm (377 kgf-cm, 27 ft. lbs.)
b. Apply a few drops of adhesive to each of 2 threads on the tip of the 6 torque converter clutch mounting bolts.
Adhesive: Part No. 08833-00070, THREE BOND 1324 or equivalent
c. Install the 6 torque converter clutch mounting bolts.
Torque: 41 Nm (418 kgf-cm, 30 ft. lbs.)
NOTICE: First install the green colored bolt, and then the remaining 5 bolts.
d. Install the flywheel housing under cover to the automatic transaxle with the 2 bolt.
Torque: 7.8 Nm (80 kgf-cm, 69 inch lbs.)
4. INSTALL TRANSFER STIFFENER PLATE RH
a. Install the transfer stiffener plate RH with 5 bolts to the transfer and engine mounting bracket RR.
Torque: 34 Nm (350 kgf-cm, 25 ft. lbs.)
5. INSTALL ENGINE MOUNTING BRACKET FRONT
a. Install the engine mounting bracket front to the automatic transaxle with the 3 bolts.
Torque: 64 Nm (653 kgf-cm, 47 ft. lbs.)
6. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
a. Coat a new O-ring with ATF, and install it to the transmission oil filler tube sub-assembly
b. Install the transmission oil filler tube sub-assembly to the automatic transaxle with the bolt.
Torque: 5.5 Nm (56 kgf-cm, 49 inch lbs.)
c. Connect the 2 clamps to the oil filter tube.
d. Install the ATF level gauge.
7. INSTALL OIL COOLER INLET TUBE NO.1
a. Temporarily install the oil cooler outlet tube No. 1.
b. Temporarily install the oil cooler inlet tube No. 1.
c. Install the oil cooler tube clamp and bolt.
Torque: 5.4 Nm (55 kgf-cm, 48 inch lbs.)
HINT: Install them so that the oil cooler tube cushion is positioned as shown in the illustration.
d. Using SST and a wrench, tighten the oil cooler inlet tube No. 1.
SST 09023-12701
Torque: 34 Nm (347 kgf-cm, 25 ft. lbs.)
8. INSTALL OIL COOLER OUTLET TUBE NO.1
a. Using SST and a wrench, tighten the oil cooler outlet tube No. 1.
SST 09023-12701
Torque: 34 Nm (347 kgf-cm, 25 ft. lbs.)
9. INSTALL TRANSMISSION CONTROL CABLE BRACKET NO.1
a. Install the control cable bracket No.1 with the 2 bolts.
Torque: 12 Nm (122 kgf-cm, 9 ft. lbs.)
10. CONNECT CONNECTORS
a. Connect the transmission wire connector.
b. Connect the park/neutral position switch connector.
c. Connect the 2 transmission revolution sensor connectors.
11. INSTALL STARTER ASSEMBLY
a. Install the starter assembly with the 2 bolts (1).
Torque: 37 Nm (377 kgf-cm, 27 ft. lbs.)
b. Connect the connector (2).
c. Connect the starter wire with the nut (3).
Torque: 9.8 Nm (100 kgf-cm, 87 inch lbs.)
12. CONNECT WIRE HARNESS
a. Connect the wire harness with the bolt.
Torque: 13 Nm (133 kgf-cm, 10 ft. lbs.)
13. INSTALL WIRE HARNESS CLAMP
a. Install the 4 clamps and 4 bolts.
Torque: 8.4 Nm (86 kgf-cm, 74 inch lbs.)
b. Connect the wire harnesses to the clamps.
14. INSTALL TRANSMISSION CONTROL CABLE BRACKET NO.2
a. Install the transmission control cable bracket No.2 with the bolt.
Torque: 12 Nm (122 kgf-cm, 9 ft. lbs.)
15. INSTALL LH FRONT DRIVE SHAFT ASSEMBLY
16. INSTALL RH FRONT DRIVE SHAFT ASSEMBLY
17. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
18. RESET MEMORY
19. PERFORM INITIALIZATION
HINT: Some system need initialization when disconnecting the cable from the negative battery terminal.