Shifter A/T: Service and Repair

SHIFT LEVER

Components:

REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
a. Turn the shift lever knob sub-assembly in the direction indication by the arrow and remove it.
3. REMOVE CONSOLE PANEL UPPER FRONT
4. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER
5. REMOVE FRONT DOOR SCUFF PLATE LH
6. REMOVE FRONT DOOR SCUFF PLATE RH
7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
9. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER
10. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
11. REMOVE FLOOR CARPET COVER CENTER LH
12. REMOVE FLOOR CARPET COVER CENTER RH
13. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER

14. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
a. Using a screwdriver, disconnect the cable end from the shift lever assembly
b. Turn the socket of the transmission control cable assembly counterclockwise and remove the stopper cap.
c. Disconnect the transmission control cable assembly from the shift lever assembly

15. REMOVE SHIFT LEVER ASSEMBLY
a. Disconnect the pattern select switch connector, the shift rock control computer connector and the indicator light wire connector.

b. Remove the 4 nuts and disconnect the shift lever assembly from the vehicle.

DISASSEMBLY

1. REMOVE POSITION INDICATOR HOUSING
a. Using a screwdriver, remove the position indicator housing from the shift lever assembly.

2. REMOVE SHIFT LEVER CAP
a. Using a screwdriver, remove the shift lever cap from the position indicator housing.

3. REMOVE PATTERN SELECT SWITCH ASSEMBLY NO.1
a. Remove the pattern select switch assembly No.1 from the position indicator housing.

4. REMOVE SHIFT LOCK RELEASE LINK NO.1
a. Remove the shift lock release link, spring and cover from the position indicator housing.

5. REMOVE POSITION INDICATOR LIGHT GUIDE
a. Remove the indicator light wire sub-assembly from the shift lever assembly

b. Using a screwdriver, remove the position indicator light guide from the shift lever assembly.

6. REMOVE POSITION INDICATOR SLIDE COVER
a. Remove the position indicator slide cover from the position indicator housing lower.

7. REMOVE POSITION INDICATOR SLIDE COVER
a. Remove the position indicator slide cover No.2 from the position indicator slide cover.

8. REMOVE POSITION INDICATOR HOUSING LOWER
a. Remove the position indicator housing lower from the shift lock control unit.

9. REMOVE INDICATOR LIGHT WIRE SUB-ASSEMBLY
a. Gate shift lever:
1. Remove the connector from the shift lever assembly

b. Shift lever with multi-mode automatic transmission:
1. Remove the connector from the shift lever assembly
2. Using a screwdriver, release the stopper of the connector.
3. Using a screwdriver, disengage the locking lug of terminals (1) and (6), and pull the terminals out from the rear.

ADJUSTMENT
1. INSPECT SHIFT LEVER POSITION
a. When shifting from the P to R position only with the ignition switch on and brake pedal depressed, make sure that the shift lever moves smoothly and can be moderately operated.
b. Start the engine and make sure that the vehicle moves forward when shifting from the N to D position and moves rearward when shifting to the R position.

2. ADJUST SHIFT LEVER POSITION
a. Loosen the nut on the control shaft lever.

b. Push the control shaft fully downward.
c. Return the control shaft lever 2 notches to the N position.

d. While pushing the control cable end up with the shift lever in the N position, install it to the control shaft lever with the nut.
Torque: 15 Nm (150 kgf-cm, 10 ft. lbs.)

NOTICE:
^ If the control cable end is excessively pushed up, the shift lever can not be adjusted.
^ When tightening the nut, confirm that the control cable is properly stretched.

e. Start the engine and make sure that the vehicle moves forward when shifting the lever from the N to D position and moves rearward when shifting it to the R position.

REASSEMBLY

1. INSTALL INDICATOR LIGHT WIRE SUB-ASSEMBLY
a. Shift lever with multi-mode automatic transmission:
1. Connect the 2 terminals of indicator light wire harness to the connector of transmission control switch.
2. Install the connector to the shift lever assembly

b. Gate shift lever:
1. Install the connector to the shift lever assembly

2. INSTALL POSITION INDICATOR HOUSING LOWER
a. Install the position indicator housing lower to the shift lock control unit.

HINT: Engage the claws securely

3. INSTALL POSITION INDICATOR SLIDE COVER
a. Install the position indicator slide cover No.2 to the position indicator slide cover.

4. INSTALL POSITION INDICATOR SLIDE COVER
a. Install the position indicator slide cover to the position indicator housing lower.

NOTICE: Install the position indicator slide cover No.2 with the boss facing the rear of the vehicle.

5. INSTALL POSITION INDICATOR LIGHT GUIDE
a. Install the position indicator light guide to the position indicator housing lower.

HINT: Engage the claws securely.

b. Install the indicator light wire sub-assembly to the shift lever assembly.

6. INSTALL SHIFT LOCK RELEASE LINK NO.1
a. Apply MP grease to the shift lock release link and spring.
b. Install the shift lock release link, spring and cover.

7. INSTALL PATTERN SELECT SWITCH ASSEMBLY NO.1
a. Install the pattern select switch assembly No. 1 to the position indicator housing.

8. INSTALL SHIFT LEVER CAP
a. Install the shift lever cap to the position indicator housing.

9. INSTALL POSITION INDICATOR HOUSING
a. Install the position indicator housing to the shift lever assembly.

HINT: Engage the claws securely

INSTALLATION

1. INSTALL SHIFT LEVER ASSEMBLY
a. Install the shift lever assembly with the 4 nuts.
Torque: 12 Nm (122 kgf-cm, 9 ft. lbs.)

HINT: Tighten them in the order, A, B, C and D.

NOTICE: Be careful not to put the wirings of the indicator light or the shift lock system between the floor shift assembly and the floor while installing the floor shift assembly.

b. Install the pattern select switch connector, the shift lock control computer connector and the indicator light wire connector.

2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
a. Connect the socket of the transmission control cable assembly to the shift lever assembly
b. Connect the control cable end to the shift lever assembly.
c. Push the stopper cap to the socket as shown in the illustration.
d. Turn the socket of the transmission control cable assembly clockwise and install the stopper cap.

NOTICE:
^ To prevent torsion of the inner cable, the end with the eye should face up.
^ Push the cable end to the bottom of the pin.
^ Confirm that the connection between the socket and the shift rock control unit is fixed.

3. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
a. Install the shift lever knob sub-assembly.
4. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER
5. INSTALL FLOOR CARPET COVER CENTER RH
6. INSTALL FLOOR CARPET COVER CENTER LH
7. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
8. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER
9. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
11. INSTALL FRONT DOOR SCUFF PLATE RH
12. INSTALL FRONT DOOR SCUFF PLATE LH
13. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER
14. INSTALL CONSOLE PANEL UPPER FRONT
15. CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
16. INSPECT SHIFT LEVER POSITION
17. ADJUST SHIFT LEVER POSITION
18. PERFORM INITIALIZATION