Operation CHARM: Car repair manuals for everyone.
Home >> Lexus >> 2008 >> GX 470 V8-4.7L (2UZ-FE) >> Repair and Diagnosis >> Body and Frame >> Seats >> Service and Repair >> Front Seat Assembly (for LH Side) >> Disassembly

Disassembly








SEAT: FRONT SEAT ASSEMBLY (for LH Side): DISASSEMBLY

DISASSEMBLY

1. REMOVE RECLINING POWER SEAT SWITCH KNOB
(a) Using a screwdriver, remove the reclining power seat switch knob.
HINT: Tape the screwdriver tip before use.

2. REMOVE SLIDE & VERTICAL POWER SEAT SWITCH KNOB
(a) Using a screwdriver, remove the slide & vertical power seat switch knob.
HINT: Tape the screwdriver tip before use.

3. REMOVE FRONT SEAT CUSHION SHIELD INNER LH






(a) Remove the 5 screws.
(b) Using a screwdriver, disengage the 2 claws and remove the front seat cushion shield inner No.1 LH with the front seat cushion shield LH, and then disconnect the connector.
HINT: Tape the screwdriver tip before use.

(c) Remove the screw and front seat cushion shield inner No.1 LH.
4. REMOVE POWER SEAT SWITCH ASSEMBLY
(a) Remove the 2 screws and power seat switch assembly.
5. REMOVE POSITION CONTROL ECU & SWITCH ASSEMBLY
(a) Disconnect the connectors.
(b) Remove the 3 screws and position control ECU & switch assembly.
6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
7. REMOVE FRONT SEAT CUSHION SHIELD INNER LH






(a) Remove the screw.
(b) Using a screwdriver, disengage the claw and clip, and remove the front seat cushion shield inner LH.
HINT: Tape the screwdriver tip before use.

8. REMOVE SEAT TRACK UPPER RAIL COVER LH
(a) Using a screwdriver, remove the seat track upper rail cover LH.
HINT: Tape the screwdriver tip before use.

9. REMOVE SEAT TRACK UPPER RAIL COVER RH
HINT: Removal procedure of the seat track UPR rail cover RH is the same as for the seat track upper rail cover LH.

10. REMOVE FRONT SEAT LEG COVER NO. 1
(a) Using a screwdriver, remove the front seat leg cover No.1.
HINT: Tape the screwdriver tip before use.

11. REMOVE FRONT SEAT LEG COVER LH
HINT: Removal procedure of the front seat leg cover LH is the same as for the front seat leg cover No.1.

12. REMOVE SEAT CUSHION COVER WITH PAD
(a) Disconnect the connector.
(b) Remove the 2 clips.
(c) Disengage the hook and remove the seat cushion cover together with the pad.
13. REMOVE SEAT CUSHION COVER
(a) Remove the hog rings and seat cushion cover.
14. REMOVE FRONT SEAT HEADREST ASSEMBLY
15. REMOVE SEAT ARMREST CAP NO. 1
(a) Remove the seat armrest cap No. 1.
16. REMOVE FRONT ARMREST ASSEMBLY LH
(a) Remove the bolt and seat armrest assembly LH.
17. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH
(a) Remove the 2 screws and front seatback board sub-assembly LH.
18. REMOVE FRONT SEATBACK BOARD COVER SUB-ASSEMBLY
(a) Remove the front seatback board cover sub-assembly.
19. REMOVE FRONT SEAT HEADREST SUPPORT






(a) Remove the 2 front seat headrest supports.
20. REMOVE SEATBACK COVER WITH PAD
(a) Disconnect the connector.






(b) Disengage the clamp and disconnect the wire harness.
NOTE: Be careful not to damage the cover.





(c) Remove the hog rings, nut and seatback cover bracket.
(d) Remove the hog rings and seatback cover together with the pad.
21. REMOVE FRONT SEATBACK COVER
(a) Remove the hog rings and front seatback cover.
22. REMOVE RECLINING ADJUSTER INSIDE COVER LH
(a) Remove the 2 screws and reclining adjuster inside cover LH (lower).
(b) Remove the screw and reclining adjuster inside cover LH (upper).
23. REMOVE RECLINING ADJUSTER OUTSIDE COVER RH
(a) Remove the 2 screws and reclining adjuster inside cover RH (lower).
(b) Remove the screw and reclining adjuster inside cover RH (upper).
24. REMOVE VERTICAL ADJUSTER BRACKET COVER LH
(a) Remove the screw and vertical adjuster bracket cover LH.
25. REMOVE VERTICAL ADJUSTER BRACKET COVER RH
(a) Remove the screw and vertical adjuster bracket cover RH.
26. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH
(a) Disconnect the connector.
(b) Remove the 2 screws and lumbar support adjuster assembly LH.
27. REMOVE LUMBAR SUPPORT POWER SEAT MOTOR ASSEMBLY
(a) Remove the 3 screws and lumbar support power seat motor assembly.
28. REMOVE POWER SEAT MOTOR ASSEMBLY (for Driver Side)
(a) Disconnect the connectors.
(b) Using a hexagon wrench 4.0 mm (0.15 in.), remove the 3 hexagon bolts and power seat motor assembly (reclining).
(c) Using a hexagon wrench 4.0 mm (0.15 in.), remove the 2 hexagon bolts, nut and power seat motor assembly (lifter).
(d) Using a hexagon wrench 4.0 mm (0.15 in.), remove the 2 hexagon bolts, nut and power seat motor assembly (front vertical).
29. REMOVE POWER SEAT MOTOR ASSEMBLY (for Front Passenger Side)
(a) Disconnect the connectors.
(b) Using a hexagon wrench 4.0 mm (0.15 in.), remove the 3 hexagon bolts and power seat motor assembly (reclining).
(c) Using a hexagon wrench 4.0 mm (0.15 in.), remove the 2 hexagon bolts, nut and power seat motor assembly (slide).
30. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH
(a) Disconnect the connector.
(b) Remove the seat heater control sub-assembly LH.
31. REMOVE SEAT POSITION AIR BAG SENSOR
32. REMOVE OCCUPANT CLASSIFICATION ECU
33. REMOVE FRONT SEAT TRACK ASSEMBLY OUTER LH
(a) Disconnect the connector.
(b) Using a torx socket wrench (T40), remove the 6 torx bolts and front seat track assembly outer LH.
34. REMOVE FRONT SEAT CUSHION PROTECTOR
(a) Remove the 2 front seat cushion protectors.
pro multis · About Operation CHARM