Disassembly

SEAT: REAR SEAT ASSEMBLY (for Rear No. 1 Seat): DISASSEMBLY

DISASSEMBLY

1. REMOVE REAR SEAT CUSHION COVER
(a) Using a screwdriver, remove the screw cover, screw and the release handle.
(b) Disengage the claws, remove the 2 screws and the reclining cover.





(1) LH Side (Rear No. 1 Seat LH)





(2) RH Side (Rear No. 1 Seat RH)
(c) Disengage the claws, remove the 2 screws and the reclining cover.





(1) LH Side (Rear No. 1 Seat LH)





(2) RH Side (Rear No. 1 Seat RH)
(d) Disengage the seatback cover hem.





(1) Rear No. 1 Seat LH:





(2) Rear No. 1 Seat RH:
(e) Insert a screwdriver between the seat cushion cover and seat cushion under cover.





(1) Rear No. 1 Seat LH:





(2) Rear No. 1 Seat RH:
NOTE: Tape the screwdriver tip before use.

(f) Pry the seat cushion cover hem to disengage it.
(g) Cut the hog rings and bring out the seat cushion cover together with the pad.
(h) Remove the nut and disconnect the rear seat 3 point type seat belt assembly LH.
(i) Remove the seat cushion cover together with the pad.
(j) Cut the hog rings and remove the seat cushion cover from the pad.
2. REMOVE REAR SEAT ARMREST ASSEMBLY CENTER
(a) Open the fastener of the seatback cover.
(b) Remove the screw and the armrest cover.
(c) Remove the 3 bolts, guide, armrest hinge and the armrest.
3. REMOVE REAR SEATBACK ASSEMBLY
4. REMOVE REAR SIDE SEATBACK COVER
(a) Disconnect the seat lock control cables from the seatback frame.
(b) Remove the 3 bolts, washer, grommet and the seatback stopper plate.
(c) Disengage the claws, remove the 2 screws and the 2 reclining covers.
(d) Remove the 4 bolts and the rear seatback assembly LH.
5. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY
(a) Remove the 2 tether anchor covers.
(b) Remove the rear seat protector.
(c) Push the claws and remove the 4 headrest supports.
(d) Remove the rear seat shoulder belt hole cover.
(e) Remove the seatback cover together with the pad.
(f) Cut the hog rings and remove the seatback cover.
6. REMOVE REAR SEAT HINGE SUB-ASSEMBLY
(a) Remove the 2 screws and the reclining adjuster cover sub-assembly.
(b) Using a screwdriver, remove the rear seat shoulder belt hole cover.
(c) Remove the 2 nuts, 2 screws and the seat belt.
7. REMOVE REAR SEAT HINGE SUB-ASSEMBLY
(a) Using a screwdriver, remove the spring of the seat stay ball-joint.





(1) Rear No. 1 Seat LH:





(2) Rear No. 1 Seat RH:
(b) Disconnect the ball-joint from the seat cushion frame.
(c) Remove the hinge cover, E-ring, pin, hinge guide, spring and the hinge together with the seat stay.
8. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
(a) Remove the 7 screws, cushion and the cover.
9. REMOVE REAR SEAT BELT INNER
(a) Remove the nut and rear seat belt inner.
(b) Remove the nut and rear seat belt inner No. 2.
10. REMOVE FOLD SEAT LOCK CONTROL CABLE ASSEMBLY NO. 2
11. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY