Removal

A760H AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION ASSEMBLY: REMOVAL

REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE COOL AIR INTAKE DUCT SEAL Removal
3. REMOVE ENGINE ROOM SIDE COVER LH Removal
4. REMOVE ENGINE UNDER COVER
5. DRAIN COOLANT Testing and Inspection
6. DRAIN AUTOMATIC TRANSMISSION FLUID
(a) Remove the drain plug and gasket, and drain the ATF.
(b) Install a new gasket and the drain plug.
Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)
7. REMOVE NO. 1 REAR FLOOR PANEL BRACE Removal
8. REMOVE FRONT CENTER FLOOR BRACE Removal
9. REMOVE OXYGEN SENSOR Removal
10. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal
11. REMOVE FRONT FLOOR NO. 1 HEAT INSULATOR Removal
12. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH Removal
13. REMOVE STARTER ASSEMBLY Removal
14. REMOVE FRONT PROPELLER SHAFT ASSEMBLY Removal
15. REMOVE OUTSIDE AIR GUIDE PLATE RH Removal
16. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY Removal
17. REMOVE FLYWHEEL HOUSING SIDE COVER





(a) Remove the flywheel housing side cover from the engine assembly.
18. REMOVE DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT





(a) Turn the crankshaft to gain access to each bolt.
(b) Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch setting bolts.
19. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY





(a) Remove the 2 bolts and No. 1 exhaust pipe support bracket sub-assembly from the automatic transmission assembly.
20. SEPARATE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
(a) Set the shift lever to the neutral position.





(b) Remove the nut and separate the floor shift gear shifting rod sub-assembly.
21. SUPPORT AUTOMATIC TRANSMISSION WITH TRANSFER ASSEMBLY





(a) Support the automatic transmission assembly with a transmission jack.
22. SEPARATE ENGINE REAR MOUNTING MEMBER





(a) Remove the 4 bolts and separate the engine rear mounting member from the body.
23. SEPARATE CONNECTOR





(a) Remove the bolt and earth wire.





(b) Tilt down the automatic transmission assembly.





(c) Disconnect the park/neutral position switch connector, transmission wire connector, and 2 transmission revolution sensor connectors.
HINT:
Disengage the claw, press down the lever, and then disconnect the transmission wire connector.

24. SEPARATE WIRE HARNESS





(a) Remove the 4 bolts and separate the wire harness clamps from the automatic transmission assembly.
25. SEPARATE WATER BY-PASS HOSE





(a) Remove the bolt and water by-pass hose clamp.
(b) Separate the 2 water by-pass hoses from the transmission oil cooler.
NOTE:
Use a container to catch any coolant which flows out of the water by-pass hoses.

26. REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER ASSEMBLY





(a) Remove the 9 bolts and automatic transmission with transfer assembly.
27. REMOVE ENGINE REAR MOUNTING MEMBER





(a) Remove the 3 nuts and engine rear mounting member from the automatic transmission assembly.
28. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR





(a) Remove the 3 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.
29. REMOVE TRANSFER DYNAMIC DAMPER





(a) Remove the 2 bolts and dynamic damper from the automatic transmission assembly.
30. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH





(a) Remove the nut and transmission control shaft lever LH from the automatic transmission assembly.
31. REMOVE TRANSMISSION OIL COOLER





(a) Remove the 3 bolts, transmission oil cooler, and spacer from the automatic transmission assembly.





(b) Remove the 4 O-rings from the valve body down shift plug spacer.
32. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY





(a) Put matchmarks on the torque converter and transmission case.
(b) Remove the torque converter from the automatic transmission assembly.
33. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY Testing and Inspection