Disassembly

ENGINE HOOD / DOOR: BACK DOOR: DISASSEMBLY

DISASSEMBLY

1. REMOVE REAR WIPER ARM COVER Removal
2. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY Removal
3. REMOVE REAR WIPER SHAFT COVER Removal
4. REMOVE REAR NO.1 WIPER LINK PIVOT NUT Removal
5. REMOVE REAR NO.1 WIPER LINK PIVOT WASHER Removal
6. REMOVE BACK WINDOW PANEL TRIM UPPER (w/o Power Back Door)





(a) Disengage the 2 claws and the 7 clips, and remove the back window panel trim upper.
7. REMOVE BACK DOOR TRIM BOARD (w/ Power Back Door)





(a) Disengage the 3 claws and remove the back door trim board.
8. REMOVE BACK WINDOW PANEL TRIM UPPER (w/ Power Back Door)





(a) Disengage the 2 claws and the 7 clips, and remove the back window panel trim upper.
9. REMOVE BACK DOOR TRIM PANEL ASSEMBLY UPPER





(a) Disengage the 10 clips and remove the back door trim panel assembly upper.
10. REMOVE BACK DOOR TRIM PANEL ASSEMBLY





(a) Disengage the 8 clips and remove the back door trim panel assembly.
11. REMOVE REAR WIPER MOTOR ASSEMBLY Removal
12. REMOVE BACK-UP LIGHT ASSEMBLY LH Removal
13. REMOVE BACK-UP LIGHT ASSEMBLY RH
HINT: Use the same procedures for the RH side and the LH side.

14. REMOVE BACK DOOR TRIM COVER RH





(a) Disengage the 3 clips and remove the back door trim cover RH.
HINT: If a clip remains on the door, remove the clip from the body and install it to the back door trim cover RH.

15. REMOVE BACK DOOR TRIM COVER LH





(a) Disengage the 3 clips and remove the back door trim cover LH.
HINT: If a clip remains on the door, remove the clip from the body and install it to the back door trim cover LH.

16. REMOVE REAR SPOILER SUB-ASSEMBLY Removal
17. REMOVE BACK DOOR TRIM SPACER (RH Side)
(a) Remove the screw.





(b) Disengage the clip and remove the back door trim spacer.
18. REMOVE BACK DOOR TRIM SPACER (LH Side)
(a) Remove the screw.





(b) Disengage the clip and remove the back door trim spacer.
19. REMOVE BACK DOOR LOCK COVER





(a) Disengage the 4 claws and remove the back door lock cover.
20. REMOVE BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)





(a) Separate the link rod as shown in the illustration.





(b) Disconnect the connector and remove the clamp.
(c) Remove the 3 bolts and the back door lock assembly.
21. REMOVE BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)





(a) Separate the link rod as shown in the illustration.





(b) Disconnect each connector and remove the clamp.
(c) Remove the 4 bolts and the back door lock assembly.
22. REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)





(a) Disconnect the connector.
(b) Remove the clip.
(c) Using a "torx" socket wrench (T30), remove the 3 screws and the power back door sensor assembly RH.
23. REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)





(a) Disconnect the connector.
(b) Remove the clip.
(c) Using a "torx" socket wrench (T30), remove the 3 screws and the power back door sensor assembly LH.
24. REMOVE BACK DOOR GARNISH
25. REMOVE BACK DOOR OPENER SWITCH ASSEMBLY





(a) Remove the 2 screws and the back door opener switch assembly.
26. REMOVE TELEVISION CAMERA (w/ Rear View Monitor) Removal
27. REMOVE LICENSE PLATE LIGHT ASSEMBLY Removal
28. REMOVE POWER BACK DOOR WARNING BUZZER (w/ Power Back Door)





(a) Disconnect the connector.
(b) Remove the clamp and power back door warning buzzer.
29. REMOVE POWER BACK DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)





(a) Remove the clamp and disconnect the connector.
(b) Disengage the 2 claws and remove the power back door control switch assembly as shown in the illustration.
30. REMOVE DOOR PULL HANDLE





(a) Disengage the 4 claws and remove the door pull handle.