Programming and Relearning

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: CALIBRATION

1. DESCRIPTION

(a) After replacing VSC-related components, clearing and reading the sensor calibration data is necessary.

(b) Follow the chart to perform calibration.





2. PERFORM YAW RATE AND ACCELERATION SENSOR AND STEERING ANGLE SENSOR ZERO POINT CALIBRATION (When Using Techstream)

NOTICE:
* While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
* Be sure to perform this procedure on a level surface (with an inclination of less than 1%).
(a) Clear the zero point calibration data.

(1) Turn the engine switch off.

(2) Check that the steering wheel is centered.

(3) Check that the shift lever is in P.

(4) Connect the Techstream to the DLC3.

(5) Turn the engine switch on (IG).

(6) Turn the Techstream on.

(7) Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Reset Memory.

(8) Select the skid control ECU to clear the zero point calibration data using the Techstream.

(9) Turn the engine switch off.

(b) Perform zero point calibration of the yaw rate and acceleration sensor.

(1) Turn the engine switch off.

(2) Check that the steering wheel is centered.

(3) Check that the shift lever is in P.

NOTICE:
* DTCs C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) and C1336 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P.
* If a DTC is output that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.
(4) Connect the Techstream to the DLC3.

(5) Turn the engine switch on (IG).

(6) Turn the Techstream on.

(7) Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Test Mode.

(8) Keep the vehicle stationary on a level surface for 5 seconds or more.

(9) Check that the slip indicator light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

HINT
* If the slip indicator light does not blink, perform zero point calibration again.
* The zero point calibration is performed only once after the system enters test mode.
* Calibration cannot be performed again until the stored data is cleared.
(10) Turn the engine switch off and disconnect the Techstream.

(c) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.

3. PERFORM YAW RATE AND ACCELERATION SENSOR AND STEERING ANGLE SENSOR ZERO POINT CALIBRATION (When Using SST Check Wire)

NOTICE:
* While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
* Be sure to perform this procedure on a level surface (with an inclination of less than 1%).
(a) Clear the zero point calibration data.

(1) Turn the engine switch off.

(2) Check that the steering wheel is centered.

(3) Check that the shift lever is in P.

(4) Turn the engine switch on (IG).

(5) The ABS warning light and slip indicator light come on for 3 seconds to indicate that the initial check is completed.

(6) Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.

SST : 09843-18040





Text in Illustration





(7) Check that the slip indicator light comes on.

(b) Perform zero point calibration of the yaw rate and acceleration sensor.

(1) Turn the engine switch off.

(2) Check that the steering wheel is centered.

(3) Check that the shift lever is in P.

NOTICE:
* DTCs 36 (Zero Point Calibration of Yaw Rate Sensor Undone) and 39 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P.
* If a DTC is output that indicates zero point calibration is incomplete, repeat the procedure starting at the step for clearing the zero point calibration data and system information.
(4) Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST : 09843-18040





Text in Illustration





(5) Turn the engine switch on (IG).

(6) Keep the vehicle stationary on a level surface for 5 seconds or more.

(7) Check that the slip indicator light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

HINT
* If the slip indicator light does not blink, perform zero point calibration again.
* The zero point calibration is performed only once after the system enters test mode.
* Calibration cannot be performed again until the stored data is cleared.
(8) Turn the engine switch off and disconnect SST from the DLC3.

(c) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.