B1823

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1820/55-B1823/55: Short in Front Driver Side - Side Squib Circuit
B1823/55 - Short to B+ in Front Driver Side - Side Squib Circuit

DESCRIPTION

The driver side - side squib circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

HINT
* Perform the simulation method by selecting the "check mode" (signal check) with the Techstream Check Mode Procedure.
* After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Check Mode Procedure.
PROCEDURE

1. CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (DRIVER SIDE - SIDE SQUIB)

(a) Turn the engine switch off.





(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(c) Disconnect the connector from the front seat side airbag assembly LH.

(d) Connect SST (resistance 2.1 Ohms) to connector "C".

CAUTION:
Never connect a tester to the front seat side airbag assembly LH (driver side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
* Do not forcibly insert the SST into the terminals of the connector when connecting.
* Insert straight the SST into the terminals of the connector.
SST : 09843-18061

(e) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(f) Turn the engine switch on (IG), and wait for at least 60 seconds.

(g) Clear the DTCs stored in the memory DTC Check / Clear.

(h) Turn the engine switch off.

(i) Turn the engine switch on (IG), and wait for at least 60 seconds.

(j) Check the DTCs DTC Check / Clear.

OK:

DTC B1820, B1821, B1822, B1823 or 55 is not output.

HINT
Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.

OK -- REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY LH
NG -- Continue to next step.

2. CHECK FLOOR WIRE NO. 2 (DRIVER SIDE - SIDE SQUIB CIRCUIT)

(a) Turn the engine switch off.





(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(c) Disconnect the SST from connector "C".

(d) Disconnect the connectors from the center airbag sensor assembly.

(e) Check for a short to B+ in the circuit.

(1) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(2) Turn the engine switch on (IG).

(3) Measure the voltage according to the value(s) in the table below.

Standard voltage:





(f) Check for an open in the circuit.

(1) Turn the engine switch off.

(2) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

(3) Measure the resistance according to the value(s) in the table below.

Standard resistance:





(g) Check for a short to ground in the circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard resistance:





(h) Check for a short in the circuit.

(1) Release the activation prevention mechanism built into connector "B" Diagnosis System.

(2) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

3. CHECK CENTER AIRBAG SENSOR ASSEMBLY

(a) Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.





(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

(c) Turn the engine switch on (IG), and wait for at least 60 seconds.

(d) Clear the DTCs stored in the memory DTC Check / Clear.

(e) Turn the engine switch off.

(f) Turn the engine switch on (IG), and wait for at least 60 seconds.

(g) Check the DTCs DTC Check / Clear.

OK:

DTC B1820, B1821, B1822, B1823 or 55 is not output.

HINT
Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY

OK -- USE SIMULATION METHOD TO CHECK