Part 2

A960E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION UNIT: DISASSEMBLY

49. REMOVE NO. 2 BRAKE DISC

(a) Using a screwdriver, remove the snap ring from the transmission case.





(b) Remove the 2 flanges, the brake piston return spring, the 4 discs and the 3 plates from the transmission case.





50. INSPECT NO. 2 BRAKE DISC Transmission Unit

51. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY Transmission Unit

52. REMOVE NO. 2 BRAKE PISTON

(a) Hold the No. 2 brake piston and apply compressed air (392 kPa, 4 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston and the No. 2 brake cylinder.





HINT
If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

(b) Remove the piston from the cylinder.

(c) Remove the 2 O-rings from the No. 2 brake piston.

53. REMOVE CENTER PLANETARY GEAR ASSEMBLY

(a) Remove the center planetary gear assembly, the planetary sun gear and the No. 4 thrust bearing race from the transmission case.





54. INSPECT CENTER PLANETARY GEAR ASSEMBLY Transmission Unit

55. REMOVE INTERMEDIATE SHAFT

(a) Using SST, remove the snap ring from the transmission case.





SST : 09350-30020

09350-07060

(b) Remove the intermediate shaft with the No. 3 one way clutch assembly from the transmission case.





56. INSPECT NO. 3 ONE WAY CLUTCH ASSEMBLY Transmission Unit

57. REMOVE NO. 3 ONE WAY CLUTCH ASSEMBLY

(a) Remove the No. 3 one way clutch assembly and the one way clutch inner race from the intermediate shaft.





58. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

(a) Remove the No. 8 thrust bearing race, the thrust needle roller bearing, the No. 7 thrust bearing race and the planetary ring gear flange from the intermediate shaft.





59. INSPECT INTERMEDIATE SHAFT Transmission Unit

60. REMOVE BRAKE PLATE STOPPER SPRING

(a) Remove the brake plate stopper spring from the transmission case.





61. REMOVE NO. 4 BRAKE DISC

(a) Remove the 4 plates, 5 discs and 2 flanges from the transmission case.





62. INSPECT NO. 4 BRAKE DISC Transmission Unit

63. REMOVE REAR PLANETARY GEAR ASSEMBLY

(a) Remove the rear planetary gear assembly from the transmission case.





(b) Remove the No. 9 thrust bearing race, thrust bearing race and the thrust needle roller bearing from the rear planetary gear assembly.





(c) Remove the thrust needle roller bearing from the transmission case.





64. INSPECT REAR PLANETARY GEAR ASSEMBLY Transmission Unit

65. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

(a) Place SST on the 1st and reverse brake return spring sub-assembly and compress the brake return spring.





SST : 09350-30020

09350-07050

(b) Using the SST, remove the snap ring and the brake return spring.

SST : 09350-30020

09350-07070

66. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY Transmission Unit

67. REMOVE BRAKE APPLY TUBE

(a) Remove the brake apply tube from the 1st and reverse brake piston.





68. REMOVE 1ST AND REVERSE BRAKE PISTON

(a) Hold the 1st and reverse brake piston and blow compressed air (392 kPa, 4 kgf/cm2, 57 psi) into the transmission case to remove the brake piston.





HINT
If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

(b) Remove the brake apply tube from the piston.

(c) Remove the O-ring from the brake piston.

69. REMOVE BRAKE REACTION SLEEVE

(a) Using SST, remove the reaction sleeve.

SST : 09350-30020

09350-07080





(b) Remove the 2 O-rings from the reaction sleeve.

70. REMOVE NO. 4 BRAKE PISTON

(a) Using SST, remove the No. 4 brake piston.

SST : 09350-30020

09350-07080





(b) Remove the 2 O-rings from the No. 4 brake piston.