Installation

DRIVE SHAFT: REAR DRIVE SHAFT ASSEMBLY: INSTALLATION

1. INSTALL REAR DRIVE SHAFT ASSEMBLY

(a) Coat the spline of the inboard joint shaft assembly with gear oil.

(b) Set the shaft snap ring with the opening side facing down.

(c) Align the shaft splines and install the drive shaft assembly with a brass bar and hammer.





NOTICE:
* Be careful not to damage the drive shaft dust cover, boot and oil seal.
* Move the drive shaft assembly while keeping it level.
HINT
It is possible to determine if the inboard joint shaft is properly engaged (the shaft is in contact with the pinion shaft, and the snap ring is engaged in the pinion gear) based on the sound or feeling when the shaft is driven in.

(d) Install the rear drive shaft assembly to the rear axle carrier.

NOTICE:
Be careful not to damage the drive shaft boot.

2. INSTALL NO. 2 REAR UPPER CONTROL ARM ASSEMBLY Installation

3. TEMPORARILY TIGHTEN NO. 1 REAR UPPER CONTROL ARM ASSEMBLY Installation

4. TEMPORARILY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY Installation

5. TEMPORARILY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY Installation

6. INSTALL REAR DISC Reassembly

7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

(a) Install the rear disc brake caliper assembly and 2 new No. 1 caliper plates with 2 new bolts.





Torque : 65 Nm (663 kgf-cm, 48 ft-lbf)

NOTICE:
* Do not twist the rear brake hose when installing the rear disc brake caliper.
* Make sure that there are no foreign objects or damage to the threads.
* Do not overtighten the bolts because the hub carrier is made of aluminum and may be damaged.
8. INSTALL REAR SPEED SENSOR

(a) Install the speed sensor to the rear axle carrier with the 2 bolts.





Bolt (A) - Torque : 8.5 Nm (87 kgf-cm, 75 in-lbf)

Bolt (B) - Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)

NOTICE:
* Be careful not to damage the speed sensor.
* Prevent foreign matter from adhering to the speed sensor.
* Do not twist the sensor wire when installing the speed sensor.
9. INSTALL REAR AXLE SHAFT NUT

(a) Clean the threaded parts on the drive shaft and axle shaft nut using a non-residue solvent.

NOTICE:
* Be sure to perform this work for a new drive shaft.
* Keep the threaded parts free of oil and foreign objects.
(b) Install a new axle shaft nut.

Torque : 290 Nm (2,957 kgf-cm, 214 ft-lbf)

(c) Using a chisel and a hammer, stake the axle shaft nut.





10. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Install the No. 3 parking brake cable assembly with the 2 bolts.





Torque : 19 Nm (194 kgf-cm, 14 ft-lbf)

11. INSTALL REAR STABILIZER LINK ASSEMBLY Installation

12. STABILIZE SUSPENSION Installation

13. FULLY TIGHTEN NO. 1 REAR UPPER CONTROL ARM ASSEMBLY Installation

14. FULLY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY Installation

15. FULLY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY Installation

16. INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

(a) Install the No. 2 differential support protector to the rear suspension member brace with the 2 nuts.





Torque : 5.4 Nm (55 kgf-cm, 48 in-lbf)

17. INSTALL REAR WHEEL

Torque : 103 Nm (1,050 kgf-cm, 76 ft-lbf)

18. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Rear Wheel Alignment

19. CHECK ABS SPEED SENSOR SIGNAL

Test Mode Procedure