Canada - Navigation System - Navigation Map Update

Bulletin
TSB2537R

Issue Date
December 3, 2007

Title
HDD NAVIGATION MAP UPDATE PROCESS

Component
TOOLS & EQUIPMENT

Models
All vehicles equipped with HDD Navigation

TSB REVISION NOTICE:
- October 12, 2010: Parts Information table has been updated.
- Generation 6 steps have been added.
Previous versions of this TSB should be discarded. Be sure to review the entire content of this service bulletin before proceeding.

INTRODUCTION:

Lexus models equipped with Hard Disk Drive (HDD) Navigation require a Special Service Tool and follow a unique process for updating map, points of interest, and system software. Instead of individual DVDs installed into the vehicle, all Map Data is uploaded directly to the HDD system.

Map Data will be released annually through the direct shipment of one Map Data DVD to each dealership service manager. The annual Map Data release must then be installed onto the Navigation Update Tool. Individual map updates are then loaded into vehicles with special map security keys. These keys are available through the normal parts ordering system. Keys are loaded onto the Navigation Update Tool through a PC or ETAS Techstream unit using software found on ETAS.

Follow the procedures listed in this bulletin to:
- Identify the current version of Map Data on the vehicle and on the Navigation Update Tool.
- Load Map Data onto the Navigation Update Tool.
- Load map security key(s) onto the Navigation Update Tool.
- Connect the Navigation Update Tool to the vehicle and update the Map/System Data to the latest version.

NOTE
- In order to perform the procedures outlined in this TSB, you MUST have completed the setup procedure in TSB2438, "HDD Navigation Program Setup" using new software version 1.3.3 as posted on E-TAS
- Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.).
- For additional details, refer to the Navigation Update Tool Operator's Manual on ETAS.

APPLICABILITY:

WARRANTY INFORMATION:

PARTS INFORMATION:

REQUIRED MATERIALS:

REQUIRED TOOLS & EQUIPMENT:

VERSION VERIFICATION:

Checking for Map Data Version on Navigation Update Tool

1. Open the Navigation Programs Installer.

NOTE
- When properly installed, the Navigation Programs Installer icon will be found on the ETAS Techstream desktop.
- Please ensure that you have the latest software version 1.3.3 installed.
- If the application is NOT properly installed, refer to TSB2438, "HDD Navigation Program Setup".

2. Click Version Check on the Navigation Update Tool Main Menu.

3. Connect the Navigation Update Tool.
A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.
B. Confirm that the Navigation Update Tool is powered correctly.
C. Turn power ON.
D. Press Continue.

4. Compare the Map version with the Map version shown on the DVD.

NOTE
- If the Map version on the Navigation Update Tool is the same as shown on Navigation Programs Installer, then go to the "Security Key Load" in this TSB.
- If the Map version on the Navigation Update Tool is NOT the same as shown on Navigation Programs Installer, then go to the "Tool Load" in this TSB.

Checking Map Data version on Vehicle HDD Navigation System (Generation 5):

1. Turn vehicle ignition ON (engine OFF).

2. From the multi-information display, press I Agree.

3. Press the MENU button

4. From the multi-information display, press HDD Data.

5. Compare the Map Data version on the Navigation System to that on the Navigation Update Tool.

NOTE
- If the Map version on the Navigation System is the same as shown on Navigation Update Tool, then the vehicle does NOT need the update.
- If the Map version on the Navigation System is NOT the same as shown on Navigation Update Tool, then go to the "Tool Load" in this TSB.

Checking Map Data version on Vehicle HDD Navigation System (Generation 6):

1. Turn vehicle ignition ON (engine OFF).

2. Press the INFO/PHONE button.

3. From the multi-information display, press Map Data.

4. Compare the Map Data version on the Navigation System to that on the Navigation Update Tool.

NOTE
- If the Map version on the Navigation System is the same as shown on the navigation update tool, then the vehicle does NOT need the update.
- If the Map version on the Navigation System is NOT the same as shown on the navigation update tool, then go to the "Tool Load" in this TSB.

TOOL LOAD:

NOTE
There are three separate processes used to update the Map Data on the vehicle:
- Loading the Map Data onto the Navigation Update Tool
- Loading the Map Data security key onto the Navigation Update Tool
- Loading the Map Data into the vehicle HDD Navigation System
1. Generation 5
2. Generation 6

If the Map version on the Navigation Update Tool is the same as shown on Navigation Update Tool, then go to the "Security Key Load" in this TSB.

If the Map version on the Navigation Update Tool is NOT the same as shown on Navigation Update Tool, then follow the instructions below.

Loading Map Data onto Navigation Update Tool

NOTE
Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.).

2. Select Load Map Data on the Navigation Update Tool Main Menu.

4. Insert Map Disk 1 into the CD/DVD-ROM drive and press Continue.

5. Allow Map Data to copy onto the PC hard drive (requires about 30 minutes).

If necessary:
- Insert the additional Map Disk (if provided) as instructed into the CD/DVD-ROM drive.
- Allow the additional Map Data to copy onto the PC hard drive (requires about 30 minutes).

6. Verify the correct version of Map data to load onto the Navigation Update Tool.

7. Click Continue to load Map Data onto the Navigation Update Tool.
Map Data will then copy to the Navigation Update Tool (requires about 15 minutes).

8. Verify the Map Data is loaded onto the Navigation Update Tool and can now be used to update the vehicle.

SECURITY KEY LOAD:

NOTE
- In order to load the Map Data onto the vehicle's Navigation System, you MUST load a security key EACH time.
- The Navigation Update Tool will hold up to ten security keys. One key is required per vehicle update.
- Storing keys on the Navigation Update Tool is NOT recommended.
- Map Data MUST be loaded onto the Navigation Update Tool before a Key File can be loaded.
- Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.).

2. Select Load Key File on the Navigation Update Tool Main Menu.

4. Connect USB Key File and press Continue.

5. Click Load to continue.

6. Allow the Key File to copy onto the Navigation Update Tool (requires about 5 seconds).

7. Verify the Key File is loaded onto the Navigation Update Tool and can now be used to update the vehicle.

NOTE
- The Navigation Update Tool will hold up to ten security keys. One key is required per vehicle update.
- Storing keys on the Navigation Update Tool is NOT recommended.

VEHICLE LOADING:

NOTE
- The Map Data security key MUST be loaded onto the Navigation Update Tool before Map Data can be loaded to the vehicle.
- Prior to connecting to the vehicle you MUST disconnect the Navigation Update Tool from the PC.
- Connect the battery charger to the vehicle prior to beginning the process to ensure constant battery voltage.

Loading Map Data onto vehicle HDD Navigation System (Generation 5)

NOTE
Prior to connecting to the vehicle you MUST disconnect the Navigation Update Tool from the PC.

1. Connect the Navigation Update Tool to the vehicle.
A. Make sure the IEEE1394 cable is secured in both the Navigation Update Tool and the vehicle connector.
B. Confirm the Navigation Update Tool is powered correctly.

2. Turn vehicle ignition ON (engine OFF).

3. From the multi-information display, press I Agree.

4. Press the "MENU" button.

5. From the multi-information display, press HDD Data.

6. Press Map Data Update.

7. Press I Agree.

8. Allow Map Data to copy (requires about 25 minutes).

9. Press OK.
10. Disconnect the Navigation Update Tool from the vehicle.

Loading Map Data onto vehicle HDD Navigation System (Generation 6)

NOTE
Prior to connecting to the vehicle you MUST disconnect the Navigation Update Tool from the PC.

3. Press the INFO/PHONE button.

4. From the multi-information display, press Map Data.

5. Press Map Data Update.

6. Press I Agree.

7. Allow Map Data to copy (requires about 25 minutes).

8. Press OK.
9. Disconnect the Navigation Update Tool from the vehicle.

NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available.
IT DOES NOT CONSTITUTE AN AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.