Operation Check
NAVIGATION: NAVIGATION SYSTEM (for DVD): OPERATION CHECK
1. CHECK SYSTEM NORMAL CONDITION
(a) If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.
(b) The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or display and navigation module display.
(1) The current position mark may be displayed on a nearby parallel road.
(2) Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.
(3) When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.
(4) When the vehicle is carried, such as on a ferry, and the vehicle itself is not running, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by GPS.
(5) When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.
(6) When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees) the current vehicle position mark may deviate from the correct position.
(7) When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.
(8) When the engine switch is turned on (ACC or IG) on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.
(9) When the vehicle travels on a snowy road or a mountain path with the chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.
(10) When the tires are changed, the current vehicle position mark may deviate from the correct position.
HINT
* A change in tire diameter may cause a speed sensor error.
* Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.
2. CHECK PANEL & STEERING SWITCH
HINT
* The display and navigation module display panel switches, radio receiver assembly panel switches and steering switches are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "Panel & Steering Switch" from the "Function Check/Setting" screen.
(d) Panel & Steering Switch Check Mode
(1) Operate each switch and check that the switch names and condition are correctly displayed.
3. CHECK TOUCH SWITCH
HINT
* The touch switches on the screen are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "Touch Switch" from the "Function Check/Setting" screen.
(d) Touch Switch Check
(1) Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
HINT
* A "+" mark is displayed where the display is touched.
* The "+" mark remains on the display even after the finger is removed.
4. CHECK MIC & VOICE RECOGNITION
HINT
* The microphone and microphone input level are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options.
* Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "Mic & Voice Recognition" from the "Function Check/Setting" screen.
(d) Microphone & Voice Recognition Check
(1) When speaking into the microphone, check that the microphone input level meter changes according to the input level.
(2) Push the recording switch and perform voice recording.
(3) Check that the recording indicator remains on while recording and that the recording can be played normally.
HINT
* For details of this function, refer to Diagnosis Display Detailed Description Navigation System (For DVD).
* This function is controlled by the display and navigation module display (built-in navigation ECU).
5. CHECK COLOR BAR
HINT
* The display color on the screen is checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "Color Bar" from the "Function Check/Setting" screen.
(d) Color Bar Check Mode
(1) Select a color bar from the "Color Bar Check Mode" screen.
(2) Check the display color.
HINT
* The entire screen turns to the color or stripe selected.
* Touching the display will return to the "Color Bar Check" screen.
6. CHECK GPS & VEHICLE SENSORS
HINT
* GPS information, vehicle signals and sensor signals are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "GPS & Vehicle Sensors" from the "Function Check/Setting" screen.
(d) GPS information
(1) When GPS information is displayed, check the GPS conditions.
HINT
* This screen is updated once per second when input signals to the vehicle are changed.
* For details of this function, refer to Diagnosis Display Detailed Description in System Description Navigation System (For DVD).
(e) Select "Sensors Check" from the "GPS Information" screen.
(f) Vehicle Sensors
(1) Check all the signals and sensors when vehicle signal information is displayed.
HINT
* This screen is updated once per second when input signals to the vehicle are changed.
* This screen displays vehicle signals input to the display and navigation module display (built-in navigation ECU).
* For details of this function, refer to Diagnosis Display Detailed Description in System Description Navigation System (For DVD).
7. CHECK VEHICLE SIGNAL
HINT
* Vehicle signals received by the display and navigation module display are checked in the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "Vehicle Signal" from the "Function Check/Setting" screen.
(d) Vehicle Signal Check Mode
(1) When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
HINT
* Only conditions having inputs are displayed.
* This screen displays vehicle signals input to the display and navigation module display.
* For details of this function, refer to Diagnosis Display Detailed Description in System Description Navigation System (For DVD).
8. CHECK HANDSFREE VOLUME SETTING
HINT
* The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
(a) Enter diagnostic mode Navigation System (For DVD).
(b) Select "Function Check/Setting" from the "Service Menu" screen.
(c) Select "Hands-free Volume Setting" from the "Function Check/Setting" screen.
(d) Hands-free Volume Setting
(1) Check the hands-free volume level.
NOTICE:
Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the receive voice quality is still acceptable after changing this setting.