B1653

SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1653/35: Seat Position Airbag Sensor Circuit Malfunction
B1653/35 - Seat Position Airbag Sensor Circuit Malfunction

DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and seat position airbag sensor.

DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK CONNECTORS

(a) Turn the power switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

OK:

The connectors are properly connected.

HINT
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

(e) Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.

NG -- REPLACE WIRE HARNESS
OK -- Continue to next step.

2. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

(a) Connect the connectors to the front seat inner belt assembly LH and No. 2 floor wire.

(b) Using SST, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.

NOTICE:
Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST : 09843-18040

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Text in Illustration

NG -- CHECK NO. 2 FLOOR WIRE (OPEN)
OK -- Continue to next step.

3. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

(a) Disconnect SST from connector B.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Text in Illustration

NG -- CHECK NO. 2 FLOOR WIRE (SHORT)
OK -- Continue to next step.

4. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

(a) Connect the cable to the negative (-) battery terminal.

(b) Turn the power switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Text in Illustration

NG -- CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
OK -- Continue to next step.

5. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

(a) Turn the power switch off.

Text in Illustration

NG -- CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
OK -- Continue to next step.

6. CHECK SEAT POSITION AIRBAG SENSOR

(a) Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the power switch on (IG), and wait for at least 60 seconds.

(d) Clear the DTCs stored in the memory Reading and Clearing Diagnostic Trouble Codes.

(e) Turn the power switch off.

(f) Turn the power switch on (IG), and wait for at least 60 seconds.

(g) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B1653/35 is not output.

Text in Illustration

HINT
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

NG -- REPLACE SEAT POSITION AIRBAG SENSOR

OK -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting

7. REPLACE SEAT POSITION AIRBAG SENSOR

(a) Turn the power switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Replace the seat position airbag sensor with a known good part Removal.

HINT
Perform the following inspection using known good parts from another vehicle if possible.

NEXT -- Continue to next step.

8. CHECK CENTER AIRBAG SENSOR ASSEMBLY

(a) Connect the cable to the negative (-) battery terminal.

(b) Turn the power switch on (IG), and wait for at least 60 seconds.

(c) Clear the DTCs stored in the memory Reading and Clearing Diagnostic Trouble Codes.

(d) Turn the power switch off.

(e) Turn the power switch on (IG), and wait for at least 60 seconds.

(f) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC B1653/35 is not output.

Text in Illustration

HINT
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

OK -- END

9. CHECK NO. 2 FLOOR WIRE (OPEN)

(a) Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

HINT
SST has already been inserted into connector B.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Text in Illustration

NG -- REPLACE NO. 2 FLOOR WIRE

OK -- REPLACE FRONT SEAT INNER BELT ASSEMBLY LH Removal

10. CHECK NO. 2 FLOOR WIRE (SHORT)

(a) Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Text in Illustration

NG -- REPLACE NO. 2 FLOOR WIRE

OK -- REPLACE FRONT SEAT INNER BELT ASSEMBLY LH Removal

11. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

(a) Turn the power switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the power switch on (IG).

(f) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Text in Illustration

NG -- REPLACE NO. 2 FLOOR WIRE

OK -- REPLACE FRONT SEAT INNER BELT ASSEMBLY LH Removal

12. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

(a) Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Text in Illustration

NG -- REPLACE NO. 2 FLOOR WIRE

OK -- REPLACE FRONT SEAT INNER BELT ASSEMBLY LH Removal