Pinpoint Test G: The Intermittent Wiper Speed Does Not Operate Correctly - Windshield
Wipers and Washers
Pinpoint Tests
Pinpoint Test G: The Intermittent Wiper Speed Does Not Operate Correctly - Windshield
Refer to Wiring Diagram Set 81, Wipers and Washers for schematic and connector information. Diagrams By Number
Normal Operation
Under normal operation, the wiper motor receives open and ground inputs from the multifunction switch through circuits CRW17 (GN/VT), CRW18 (VT/WH) and CRW19 (BU/OG) to activate the wipers to the appropriate intermittent speeds.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Multifunction switch
- Windshield wiper motor
PINPOINT TEST G: THE INTERMITTENT WIPER SPEED DOES NOT OPERATE CORRECTLY - WINDSHIELD
NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
-------------------------------------------------
G1 VERIFY IF THE VEHICLE IS EQUIPPED WITH RAIN SENSITIVE WIPERS
NOTE: If sent here from Pinpoint Test J, GO to G2.
- Inspect the vehicle for rain sensitive wipers.
- Is the vehicle equipped with rain sensitive wipers?
Yes
IDENTIFY the customer concern and GO to Symptom Chart. Symptom Related Diagnostic Procedures
No
GO to G2.
-------------------------------------------------
G2 CHECK THE MULTIFUNCTION SWITCH
- Ignition OFF.
- Disconnect: Multifunction Switch C202.
- Carry out the Multifunction Switch component test.
- Did the multifunction switch pass the component test?
Yes
GO to G3.
No
INSTALL a new multifunction switch. REFER to Steering Column. TEST the system for normal operation.
-------------------------------------------------
G3 CHECK CIRCUITS CRW17 (GN/VT), CRW18 (VT/WH) AND CRW19 (BU/OG) FOR AN OPEN
- Disconnect: Windshield Wiper Motor C125.
- Measure the resistance between multifunction switch C202, harness side and wiper motor C125, harness side using the following chart:
- Are the resistances less than 5 ohms?
Yes
GO to G4.
No
REPAIR the circuit(s) in question. TEST the system for normal operation.
-------------------------------------------------
G4 CHECK CIRCUITS CRW17 (GN/VT), CRW18 (VT/WH) AND CRW19 (BU/OG) FOR A SHORT TO GROUND
- Measure the resistance between ground and wiper motor:
- C125-9, circuit CRW17 (GN/VT), harness side.
- C125-10, circuit CRW19 (BU/OG), harness side.
- C125-11, circuit CRW18 (VT/WH), harness side.
- Are the resistances greater than 10,000 ohms?
Yes
GO to G5.
No
REPAIR the circuit(s) in question. TEST the system for normal operation.
-------------------------------------------------
G5 CHECK FOR SHORTS IN THE WINDSHIELD WIPER MOTOR HARNESS
- Measure the resistance between wiper motor C125, harness side, using the following chart:
- Are the resistances greater than 10,000 ohms for all measurements?
Yes
GO to G6.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
G6 CHECK FOR CORRECT WIPER MOTOR OPERATION
- Disconnect all wiper motor connectors.
- Check for:
- corrosion.
- pushed-out pins.
- Connect all wiper motor connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor - Windshield Wiper Motor - Windshield.
No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation.
-------------------------------------------------