Torque Specifications
| Camshaft Sprocket to Camshaft - Bolt | 20-30 |
| Connecting Rod - Nut | 41-49 |
| Coolant Temp. Switch | 11-16 |
| Crankshaft Damper to Crankshaft - Bolt | 125-165 |
| Crankshaft Pulley to Damper - Bolt | 26-38 |
| Cylinder Head Bolt | - Torque in sequence: 20 N.m (15 lb-ft), 40 N.m (30 lb-ft), 50 N.m (37 lb-ft), Loosen bolts 2-3 turns, Retorque Long bolts to 40-50 N.m (30-37 lb-ft), Short bolts to 20-30 N.m (15-22 lb-ft), Rotate All bolts an additional 175-185 degrees (1/2 turn). |
| Distributor Cap | 2.0-2.6 |
| Distributor Hold-Down Bolt | 27-40 |
| Distributor Rotor | 2.8-3.9 |
| ECT Sensor | 8-13 |
| EGR Spacer to Intake Manifold - Bolt | 8-12 |
| EGR Valve to EGR Spacer - Nut | 20-30 |
| Flywheel to Crankshaft - Bolt | 73-87 |
| Front Cover to Cylinder Block - Bolt | 20-30 |
| Fuel Pump to Front Cover - Bolt | 20-30 |
| Fuel Tube Fitting | 20-24 |
| Fuel Tube Fitting - Inlet | 16-20 |
| Fuel Tube Fitting - Return | 12-16 |
| Heater Elbow | 8.5-13.5 |
| Heater Tube to Intake Manifold Stud - Bolt | 10-15 |
| Intake Manifold Heat Cross-Over Valve - Bolt | 8-12 |
| Intake Manifold to Cylinder Head - Bolt | - Tighten in three steps: A. 10 Nm (8 lbs ft) B. 20 Nm (15 lbs ft) C. 32 Nm (24 lbs ft) |
| Low Level Oil Sensor | 27-41 |
| Main Bearing Cap - Bolt | 88-110 |
| MCT Sensor | 8-13 |
| Oil Filter Adapter to Front Cover - Bolt | 25-30 |
| Oil Filter to Oil Filter Adapter | 10-15 Advance 1/2 turn after the gasket contacts sealing surface. |
| Oil Inlet Tube to Cylinder Block - Bolt | 20-30 |
| Oil Inlet Tube to Main Bearing Cap - Nut | 40-55 |
| Oil Pan to Cylinder Block - Bolt | 9-12 |
| PVS Valve | 8-13 |
| PVS Valves | 8-13 |
| Rocker Arm Cover to Cylinder Head - Bolts/Studs | 9-12 |
| Rocker Arm Fulcrum to Cylinder Head - Bolt | - Tighten in two steps: A. 7-15 Nm (5.1-11.0 lb ft) B. 25-35 Nm (18.4-25.8 lb ft) |
| Spark Knock Sensor | 20-26.5 |
| Spark Plug to Cylinder Head | 7-15 |
| Thermactor Check Valve to Intake Manifold | 22-26 |
| Thermostat Housing to Intake Manifold - Bolt | 20-30 |
| Vacuum Fitting to Intake Manifold | 17-25 |
| Vacuum Tree to Intake Manifold | 8-13 |
| Vacuum Tubes to Intake Manifold - Studs/Bolts | 10-15 |
| Water Pump to Front Cover - Bolt | 20-30 |
| Wiring Retainer Bracket - Nut | 10-15 |
| Lower Intake Manifold to Head | 32 |
| Air Supply Tube Clamps | 22 |
| Upper Intake Manifold to Lower Intake Manifold Bolts | 32 |
| Throttle Body to Upper Intake Manifold | 25 |
| Air Bypass Valve to Throttle Body | 10 |
| Throttle Position Sensor to Throttle Body | 1.5 |
| Fuel Pressure Regulator to Fuel Rail Assembly | 4 |
| Fuel Rail Assembly to Intake Manifold | 10 |
| Throttle Cable Bracket to Manifold | 17 |
| Manifold Support Bracket | 25 |
| Alternator Brace to Alternator | 51 |
| Alternator Brace to Water Pump and Upper Manifold | 25 |
| EGR Valve to Upper Manifold | 25 |
| EGR Tube to EGR Valve and Exhaust Manifold | 41 |
| A/C Lower Mounting Bracket to Engine Nuts | 41-61 |
| Air Pump Pivot Bolt | 40-55 |
| Air Pump to Support Bracket Bolt | 40-55 |
| Alternator Pivot Bolt | 61-75 |
| Bolt A/C Comp. Mounting (5 Places) | 41-61 |
| Bolt Front Brace to Engine Brace A/C | 41-61 |
| Bracket, Idler Front Attach Bolt Lower | 40-55 |
| Bracket, Idler Front Attach Bolt Upper | 70-95 |
| Bracket, Idler Top Bolt | 40-55 |
| Engine Bracket Reinforcement Brace to Engine Bracket - Bolt (Damper) | 47-67 |
| Engine Bracket Reinforcement Brace to Engine Bracket-Nut (Damper) | 80-107 |
| Front A/C Comp. Plate Nut to Engine Stud (2 places) | 41-61 |
| Front A/C Comp. Plate to Lower A/C Mounting Bracket Bolt | 41-61 |
| Front Brace, A/C to Engine Stud - Nut | 20-30 |
| Idler Bracket to Alternator Top Attaching Flange Bolt | 33-36 |
| Idler Pulley Adv. Bolts (2 Places) | 40-55 |
| Nut Brace to Engine, A/C | 20-30 |
| Support A/C Comp. Mounting Bolt to Bracket Assembly (2 Places) | 41-61 |