Pinpoint Test H: All Climate Controlled Seats Are Inoperative - Front
Seats
Pinpoint Test H: All Climate Controlled Seats Are Inoperative - Front
Refer to Wiring Diagram Set 119, Climate Controlled Seats for schematic and connector information. Diagrams By Number
Normal Operation
Climate controlled seat button commands are communicated from the Front Controls Interface Module (FCIM) over the Medium Speed Controller Area Network (MS-CAN) to the HVAC module and then to the Dual Climate Controlled Seat Module (DCSM). Upon receiving a command, the mode status (high, medium, low or off) is communicated from the DCSM to the HVAC module and then to the FCIM which commands the indicators on or off. The climate controlled seat system can only operate if all 3 modules are communicating correctly on the Controller Area Network (CAN).
This pinpoint test is intended to diagnose the following:
- Fuse
- Wiring, terminals or connectors
- MS-CAN
- FCIM
- HVAC module
- DCSM
PINPOINT TEST H: ALL CLIMATE CONTROLLED SEATS ARE INOPERATIVE - FRONT
NOTICE: When taking measurements at Dual Climate Controlled Seat Module (DCSM) harness connectors, do not insert the electrical probes into the female connector pins. Inserting the probes into connector pins can cause intermittent or open electrical connections after reassembly resulting in Diagnostic Trouble Codes (DTCs) and system failure. Touching the tip of these connector pins is recommended instead.
-------------------------------------------------
H1 VERIFY CLIMATE CONTROLLED SEAT BLOWER OPERATION
- Ignition OFF.
- Remove the driver and front passenger cushion Thermo-Electric Device (TED) filters to verify blower operation.
- Turn the filters to the left (counterclockwise) and remove.
- Start the engine.
- Operate climate controlled seat buttons while verifying both blowers operate.
- Does either blower operate?
Yes
If only one blower operates, GO to Symptom Chart to diagnose a single climate controlled seat is inoperative. Symptom Related Diagnostic Procedures
If both blowers operate, GO to H5.
No
GO to H2.
-------------------------------------------------
H2 VERIFY CLIMATE CONTROLLED SEAT INDICATOR ILLUMINATION
- Verify system indicator illumination.
- Does any climate controlled seat indicator illuminate or flash and then turn off?
Yes
GO to H5.
No
GO to H3.
-------------------------------------------------
H3 CHECK THE FCIM FOR DTCs
- Enter the following diagnostic mode on the scan tool: Self Test - FCIM.
- Are any DTCs retrieved?
Yes
REFER to Multifunction Electronic Modules Diagnostic Trouble Code (DTC) Chart.
No
GO to H4.
-------------------------------------------------
H4 CHECK THE HVAC MODULE FOR DTCs
- Enter the following diagnostic mode on the scan tool: Self Test - HVAC Module.
- Are any DTCs retrieved?
Yes
REFER to Multifunction Electronic Modules Diagnostic Trouble Code (DTC) Chart.
No
GO to H6.
-------------------------------------------------
H5 CHECK THE DCSM FOR DTCs
- Enter the following diagnostic mode on the scan tool: Self Test - DCSM.
- Are any DTCs present?
Yes
GO to the Dual Climate Controlled Seat Module (DCSM) DTC Chart. Dual Climate Controlled Seat Module (DCSM) DTC Chart
No
CHECK for causes of the intermittent fault. INSPECT the connectors, terminals and wiring. ATTEMPT to recreate the fault by flexing the wire harness and operating the system. CHECK the electrical connectors for corrosion, poor pin contact or pushed-out pins. REPAIR any intermittent concerns found and TIGHTEN any loose DCSM connector pins.
REPEAT the self-test.
If no intermittent concerns are found, CARRY OUT the Component Test - Thermo-Electric Device (TED) Cooling Performance for both seats. Component Tests and General Diagnostics
-------------------------------------------------
H6 MONITOR THE FCIM PIDs AND CHECK THE INPUTS
- Enter the following diagnostic mode on the scan tool: DataLogger - FCIM - PIDs.
- Driver Cooled Seat (CC_SW_D_CL_S)
- Driver Heated Seat (CC_SW_D_HSEATS)
- Passenger Cooled Seat (CC_SW_P_CL_S)
- Passenger Heated Seat (CC_SW_P_HSEATS)
- Monitor the FCIM PIDs while individually pushing driver and passenger climate controlled seat switch buttons.
- Do the PID values agree with the switch positions?
Yes
GO to H7.
No
INSTALL a new FCIM. REFER to Information and Entertainment Systems Front Controls Interface Module (FCIM). TEST the system for normal operation.
-------------------------------------------------
H7 CHECK THE DCSM USING ACTIVE COMMANDS
- Enter the following diagnostic mode on the scan tool: DataLogger - DCSM - PIDs.
- Seat Cushion Thermal Electric Device Temperature (CSHTEMP)
- Seat Back Thermal Electric Device Temperature (BK_TEMP)
- Climate-controlled Seat Heat Command (TED_HEAT_D)
- Passenger Cushion Thermal Electric Device (TED) Temperature (PCSHTMP)
- Passenger Back (TED) Temperature (PBKTMP)
- Passenger (TED) Heat Mode (TED_HEAT_P)
- NOTE: The DCSM active commands TED_HEAT_D (driver seat) and TED_HEAT_P (passenger seat) are limited to 15 seconds in the ON state, then turn OFF.
- Operate the climate controlled seats using active commands while monitoring the appropriate PIDs.
- When the command is in process, the TED temperature PIDs on the seat being commanded should momentarily increase. If no temperature increase is noted, remove the cushion blower filter and repeat the active command while physically monitoring the cushion blower for fan movement.
- Do the PID states or cushion blower movement indicate climate controlled seat operation?
Yes
INSTALL a new HVAC module. REFER to Climate Control Heating Ventilation Air Conditioning (HVAC) Module. TEST the system for normal operation.
No
INSTALL a new DCSM. REFER to Dual Climate Controlled Seat Module (DCSM) Dual Climate Controlled Seat Module (DCSM). CLEAR the DTCs. REPEAT the self-test.
-------------------------------------------------