Part 1
MODELS WITHOUT ADVANCED KEYLESS SYSTEMNOTE:
^ The following procedures are written for MMDS-IDS only. MMDS-PDS will be similar.
^ PDS does not support Module Configuration Programming (MCP) on all models. It is recommended to use IDS when performing this procedure.
^ If IDS/PDS cannot retrieve configuration data from the old odometer, a screen will automatically appear that requires As-built data. However, configuration using the As-Built data cannot transfer old odometer data to a new odometer.
^ Before starting, make sure you have all customer ignition keys since they will need to be reprogrammed to start the vehicle. A minimum of two keys are required to start vehicle.
1. Connect IDS to the vehicle.
2. Select IDS icon (from desktop).
3. Select "START NEW SESSION". Press tick (check mark box located at lower right of screen).
4. Turn ignition switch ON (do not start engine).
5. Press tick. IDS now establishes communication to PCM.
6. "Vehicle specifications" will be shown. Select YES.
7. Screen will display "Is vehicle equipped with DSC?" Select YES or NO depending on vehicle then press tick.
8. Confirm VIN is correct for vehicle being serviced. Press tick.
9. Screen shows "Vehicle Specification". Select TOOLBOX, then "MODULE PROGRAMMING". Press tick.
10. Select "PROGRAMMABLE MODULE INSTALLATION".
11. Select "IC" from the choices. Press tick.
12. Screen displays the following information:
- If the new HEC has an odometer setting of at least 100km (63 miles), the diagnostic tester is not able to copy the odometer data from the old HEC to the new HEC.
^ If you want to copy the odometer data from the old HEC to the new HEC, you need to do the "Programmable Parameters > Odometer Write" function after completing the HEC configuration procedure. Please do not delete this session until after you complete the write procedure.
Note:
If the diagnostic tester cannot read the configuration data from the old HEC, the diagnostic tester is not able to copy the odometer data to the new HEC even if you do the Odometer Write function. Review then press tick.
13. This screen displays "Set ignition switch to OFF (Position 0)". Press tick.
NOTE:
^ DO NOT turn off or disconnect IDS from vehicle when replacing instrument cluster.
14. This screen displays "Install a new module in vehicle". Remove old instrument cluster following appropriate Workshop Manual procedure. Install the new instrument cluster unit to the vehicle.
15. When done installing new instrument cluster, press tick.
16. This screen displays "Set ignition switch to ON (Position II)". Press tick.
17. Please wait while configuration is performed. When done, screen displays "IC Module Configuration Complete". Press tick.
18. This screen displays "Set ignition switch to OFF (Position 0)". Press tick.
19. Screen displays the following information:
- If you want to copy the odometer data from the old HEC to the new HEC, you need to do the "Programmable Parameters > Odometer Write" function after completing the HEC configuration procedure. Please do not delete this session until after you complete the write procedure.
Review then press tick.
20. Select "PROGRAMMABLE PARAMETERS", then "ODOMETER WRITE". Press tick.
21. Screen shows "Programmable Module Installation" and indicates "Configuration data could not be transferred from original module". Contact technical hotline to obtain VIN and VEHICLE DATA (as-built data). Press tick.
22. Enter VIN. Press tick.
23. Enter vehicle data (as-built data). Press tick.
24. This screen displays "Set ignition switch to ON (Position II)" (do not start engine). Press tick.
25. Screen shows "Configuration complete". Verify odometer data matches original module. Press tick.
26. Press "Select" button located at upper right side of screen (box with Blue dots with lines after them). A pop-up window will open, select "EXIT" and press tick.
27. Screen shows "Vehicle Specification". Go to STEP 28, the ignition keys will need to be programmed.
28. Go to TOOLBOX. Select "BODY", "SECURITY", then "PATS FUNCTIONS". Press tick.
29. Screen displays "Close all vehicle doors. Set ignition switch to ON (Position II)". Press tick.
30. Screen displays "Does this vehicle have the SKE system?" Select NO (vehicle does not have the SKE (Advanced Keyless Entry) system).
31. Select "PARAMETER RESET" from the list of choices. Press tick.
32. Screen shows "Gaining Security Access". Read the information then select "YES" at the bottom of the screen to continue.
33. Screen now displays the VIN. Verify the VIN information then select "YES" at the bottom of the screen to continue.
34. Screen now displays the VIN, Part Number, Serial Number, Outcodes and Error Control. Record the Part Number, Serial Number, Outcodes and Error Control information then select "YES" at the bottom of the screen to continue. These numbers will be used to obtain Incodes from the Mazda Service Support (MS3) system web site.
35. Obtain Incodes through MS3, one for HEC and one for PCM. On the MS3 home page select "OTHER APPLICATIONS", then "PATS". Fill out the required information and click "Submit".