Engine Emission Control - Hybrid
-
ENGINE EMISSION CONTROL - HYBRID
CAUTION: Do not remove any part of the engine emission control system. Operating the engine without the engine emission control system intact will reduce fuel economy and engine ventilation. This will weaken engine performance and shorten engine life.
The engine emission control system consists of:
- Exhaust gas circulation (EGR) system
- Positive crankcase ventilation (PCV) system
- Evaporative emissions (EVAP) system
Exhaust Gas Recirculation (EGR) System
The EGR system returns a small amount of exhaust gas into the intake manifold. This reduces the overall combustion temperature. Cooler combustion temperatures provide a significant reduction of the oxides of nitrogen (NOx) in the exhaust emissions.The engine incorporates a stepper motor-controlled EGR valve which receives its signal from the powertrain control module (PCM). Engine coolant is used to cool the EGR valve. The EGR valve and the stepper motor are serviced as an assembly.The amount of recirculated exhaust gas depends upon:
- Engine rpm
- Intake manifold vacuum
- Exhaust back pressure
- Engine coolant temperature
- Throttle position
Positive Crankcase Ventilation (PCV) System
The PCV system uses intake manifold vacuum to ventilate blow-by fumes from the crankcase and returns the fumes to the intake manifold for combustion. The PCV valve varies the amount of blow-by gases returned to the intake manifold based on available engine vacuum. The PCV valve also prevents the entry of combustion gasses backfiring into the crankcase.
The PCV system consists of a crankcase ventilation tube, a positive crankcase ventilation (PCV) valve and a crankcase vent oil separator.
Evaporative Emissions (EVAP) System
The evaporative emissions (EVAP) system consists of the:
- EVAP canister purge valve
- EVAP canister
- EVAP canister vent solenoid
- Fuel vapor tube assembly (includes the fuel tank pressure [FTP] sensor)
- Dust separator
- Fuel tank filler cap
The evaporative emissions (EVAP) system:
- prevents hydrocarbon emissions from reaching the atmosphere.
- stores fuel vapors in the EVAP canister that are generated during vehicle operation or hot soak until they can be consumed by the engine during normal engine operation.
- routes the stored fuel vapors to the engine during engine operation.
- is controlled by the powertrain control module (PCM) which, using various sensor inputs, calculates the desired amount of purge flow. The PCM regulates the purge flow, induced by the application of the intake manifold vacuum, by varying the duty cycle applied to the EVAP canister purge valve.The fuel vapors are routed:
- from the fuel tank through the fuel vapor vent valve.
- to the EVAP canister through the vapor tube assembly.
- to the engine when the EVAP vapor management valve is opened by the PCM.The fuel tank pressure (FTP) sensor:
- is part of the fuel vapor tube assembly.
- monitors the pressure levels in the fuel tank.
- communicates the pressure reading to the PCM during the OBD II leak test.The fuel vapor tube assembly:
- is mounted on the top LH side of the fuel tank.
- is used to control the flow of fuel vapors entering the EVAP system.The EVAP canister:
- is located under the vehicle midway under the LH side of the vehicle.
- contains activated carbon.
- stores fuel vapors.The fuel tank filler cap:
- relieves the system vacuum below -3.5 kPa (-16.00 inches H2 O).The EVAP canister vent solenoid:
- is normally open.
- seals the EVAP system for the inspection and maintenance (I/M 240) test and the OBD II leak and pressure tests.
- is mounted to the left center of the EVAP canister bracket.
- is repaired as a separate item.The EVAP canister purge valve:
- is normally closed.
- regulates the purging of the EVAP canisters.
- is controlled by the PCM.
- is repaired as a separate item.
- is mounted on the cowl panel.The EVAP dust separator:
- is attached to the EVAP canister bracket.
- prevents suspended dust and dirt particles from entering the evaporative emissions system.
- is repaired as a separate item.The evaporative emissions system monitor:
- is a self-test strategy within the PCM which tests the integrity of the EVAP system.
- monitors the EVAP components for leaks.
- monitors electronic EVAP components for irrationally high or low voltages.
- monitors for correct EVAP system operation.
- uses negative and positive leak test methods to test and activate the EVAP system.The EVAP running loss system leak test:
- utilizes intake manifold vacuum to test the system and involves several stages.
Vehicle Emission Control Information (VECI) Decal
The vehicle emission control information (VECI) decal:
- is located on the hood.
- lists the exhaust emission control system information.