Part 2

Part 2

Continued From Part 1 Part 1

IMMOBILIZER SYSTEM COMPONENT REPLACEMENT/KEY ADDITION AND CLEARING [ADVANCED KEYLESS SYSTEM]

- When using the PDS (Pocket PC)

- Select "Programming".

6. Then, select items from the screen menu in the following order.

- Select "PATS Functions".

7. Select "Parameter Reset" from the M-MDS screen menu and perform the procedure according to the M-MDS screen

8. Perform the security access according to the directions on the M-MDS screen. Procedures

9. Select the replaced parts according to the directions on the M-MDS.

- If the PCM is replaced: Select "PCM".

NOTE:
- At this time, do not select the other parts from the M-MDS menu.

10. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Exit (From This Menu)" to finish the M-MDS procedure.

11. After Step 10, wait 5 s or more, and then turn the ignition switch to the LOCK position.

12. Using key, turn the ignition switch to the ON position.

13. After verifying that the security light and keyless warning light illuminates for 3 s or more turn the ignition switch to the LOCK position and remove key 1.

14. Verify that the all keys can start the engine for 5 s or more after the procedure.

No. 5 Key Additional Programming Procedure Changing

NOTE:
- This procedure is performed for enabling/disabling the "No.1 Additional Key Programming Procedure (Using Two Valid Keys)" setting.
- This procedure is possible when the vehicle is new, and when replacing the keyless unit with a new one.
- If "No.1 Additional Key Programming Procedure (Using Two Valid Keys)" is set to disable, the additional key programming can be only performed using the M-MDS preventing the forging of a spare key by using two keys that can start the engine. This function is for use by rental car agencies or other companies with vehicle fleets.

Procedure

1. Using the key, turn the ignition switch to the ON position. (The key can be either the valid key or an unprogrammed key)
NOTE:
- Although the security light starts flashing and DTC 15 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

2. Connect the M-MDS to the DLC-2.

3. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

- When using the IDS (laptop PC)

- Select "Body".
- Select "Security".

- When using the PDS (Pocket PC)

- Select "Programming".

4. Then, select items from the screen menu in the following order.

- Select "PATS Functions".

5. Select "Customer Spare Key Programming Enable" or "Customer Spare Key Programming Disable" from the M-MDS screen menu. The key additional programming procedure is as follows according to the selected menu:






-
Available
x
Unavailable

6. Perform the security access according to the directions on the M-MDS screen. Procedures

7. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Exit (From This Menu)" to finish the M-MDS procedure.

8. After Step 7, wait 5 s or more and then turn the ignition switch to the LOCK position.

9. Verify that the all keys can start the engine for 5 s or more after the procedure.

No.6 Steering Lock Unit Replacement Procedure

Condition
- Have two or more keys to be programmed after the replacement.

Procedure





1. Prepare two or more keys to be programmed after the key ID number is cleared.

2. Connect the M-MDS to the DLC-2.

3. Using key 1, turn the ignition switch to the ON position.
NOTE:
- Although the security light remains illuminated and DTC 23 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

4. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

- When using the IDS (laptop PC)

- Select "Body".
- Select "Security".

- When using the PDS (Pocket PC)

- Select "Programming".

5. Then, select items from the screen menu in the following order.

- Select "PATS Functions".

6. Select "Ignition Key Code Erase" from the M-MDS screen menu and perform the procedure according to the M-MDS screen

7. Perform the security access according to the directions on the M-MDS screen. Procedures

CAUTION:
- The M-MDS displays "You must now program a minimum of two keys.", however, do not perform the key programming and proceed to Step 7. If the procedure is not followed, the engine may not be started. The key programming procedure is performed at Steps 13 to 18.

8. Perform the steering lock unit programming. Steering Lock Unit ID Code Registration

9. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Exit (From This Menu)" to finish the M-MDS procedure.

10. After Step 9, wait 5 s or more and then turn the ignition switch to the ON position.

11. Ignition switch to the LOCK position.

12. Disconnect the M-MDS from the DLC-2.

13. Using key 1, turn the ignition switch to the ON position.

14. After verifying that the security light and keyless warning light illuminate for 3 s or more, turn the ignition switch to the LOCK position and remove key 1.
NOTE:
- Although the security light remains illuminated and DTC 21 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

15. Using key 2, turn the ignition switch to the ON position.

16. Verify that the security light and keyless warning light illuminate for approx. 3 s, and then goes out.

17. After verifying that the security light goes out, turn the ignition switch to the LOCK position using key 2, and then remove key 2.

18. If programming one more keys, repeat Steps 15 to 17 with a key to be programmed as key 3. If the vehicle is left with the ignition switch in the ON position for 1 min or more, additional key programming according to Steps 15 to 17 is disabled. If this occurs, refer to the "M-MDS connecting procedure" to program any additional keys.

19. Start the engine with key 1.

20. Verify that the security light and keyless warning light operate as follows:

- From the point when the ignition switch is turned to the ON position, the security light illuminates for approx. 3 s, and goes out.
- The keyless warning light illuminates when the ignition switch is turned to the ON position, and the light goes out after approx. 1 s, and then displays the number of the programmed keys.






21. After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position using key 1, and then remove the key.

22. Repeat Steps 19 to 21 using key 2 instead of key 1.
NOTE:
- If three or more keys have already been programmed, perform Steps 19 to 21.

23. Start the engine using the card key.

CAUTION:
- Remove any key from the key cylinder.
- Close all doors.
- Bring the card key into the vehicle.

24. Verify that the security light and keyless warning light operate as follows:

- From the point that ignition switch is turned to the ON position, the security light illuminates for approx. 3 s, and goes out.
- The keyless warning light illuminate when the ignition switch is turned to the ON position for approx. 1 min, and goes out.

25. After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position.

26. Verify that the all keys can start the engine for 5 s or more after the procedure.

No.7 Keyless control module Replacement Procedure

CAUTION:
- Do not place the following devices in the vehicle while programming, otherwise programming cannot be performed:

- Card key
- M-MDS
- Personal computer
- Devices that can send/receive the radio waves

Condition
- Have two or more keys to be programmed after the replacement.
- Have one or more card keys to be programmed after the replacement.

Procedure





1. Prepare two or more keys to be programmed after the key ID number is cleared.

2. Connect the M-MDS to the DLC-2.

3. Using key 1, turn the ignition switch to the ON position.
NOTE:
- Although the security light starts flashing and DTC 15 or DTC 23 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

4. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

- When using the IDS (laptop PC)

- Select "Body".
- Select "Security".

- When using the PDS (Pocket PC)

- Select "Programming".

5. Then, select items from the screen menu in the following order.

- Select "PATS Functions".

6. Select "Parameter Reset" from the M-MDS screen menu and perform the procedure according to the M-MDS screen

7. Perform the security access according to the directions on the M-MDS screen. Procedures

8. Select the replaced parts according to the directions on the M-MDS.

- If the keyless control module is replaced: Select "SKE".

NOTE:
- At this time, do not select the other parts from the M-MDS menu.

9. Select "Ignition Key Code Erase" from the M-MDS screen menu and perform the procedure according to the M-MDS screen.

CAUTION:
- The M-MDS displays "You must now program a minimum of two keys.", however, do not perform the key programming and proceed to Step 9. If the procedure is not followed, the engine may not be started. The key programming procedure is performed at Steps 16 to 21.

10. Perform the card key programming. Card Key ID Code Registration

11. Perform the steering lock unit programming. Steering Lock Unit ID Code Registration

12. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Exit (From This Menu)" to finish the M-MDS procedure.

13. After Step 12, wait 5 s or more and then turn the ignition switch to the ON position.

14. Ignition switch to the LOCK position.

15. Disconnect the M-MDS from the DLC-2.

16. Using key 1, turn the ignition switch to the ON position.

17. After verifying that the security light and keyless warning light illuminate for 3 s or more, turn the ignition switch to the LOCK position and remove key 1.
NOTE:
- Although the security light remains illuminated and DTC 21 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

18. Using key 2, turn the ignition switch to the ON position.

19. Verify that the security light and keyless warning light illuminate for approx. 3 s, and then goes out.

20. After verifying that the security light goes out, turn the ignition switch to the LOCK position using key 2, and then remove key 2.

21. If programming one more keys, repeat Steps 18 to 20 with a key to be programmed as key 3. If the vehicle is left with the ignition switch in the ON position for 1 min or more, additional key programming according to Steps 18 to 20 is disabled. If this occurs, refer to the "M-MDS connecting procedure" to program any additional keys.

22. Start the engine with key 1.

23. Verify that the security light and keyless warning light operate as follows:

- From the point when the ignition switch is turned to the ON position, the security light illuminates for approx. 3 s, and goes out.
- The keyless warning light illuminates when the ignition switch is turned to the ON position, and the light goes out after approx. 1 s, and then displays the number of the programmed keys.






24. After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position using key 1, and then remove the key.

25. Repeat Steps 22 to 24 using key 2 instead of key 1.
NOTE:
- If three or more keys have already been programmed, perform Steps 22 to 24.

26. Start the engine using the card key.

CAUTION:
- Remove any key from the key cylinder.
- Close all doors.
- Bring the card key into the vehicle.

27. Verify that the security light and keyless warning light operate as follows:

- From the point that ignition switch is turned to the ON position, the security light illuminates for approx. 3 s, and goes out.
- The keyless warning light illuminate when the ignition switch is turned to the ON position for approx. 1 min, and goes out.

28. After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position.

29. Verify that the all keys can start the engine for 5 s or more after the procedure.

No.8 The Procedure For When Several Parts (PCM, Keyless Control Module, and Steering Lock Unit) are Replaced at The Same Time

CAUTION:
- Do not place the following devices in the vehicle while programming, otherwise programming cannot be performed:

- Card key
- M-MDS
- Personal computer
- Devices that can send/receive the radio waves

Condition
- The menu executed on the M-MDS varies depending on the replaced parts. Verify the M-MDS menu to be executed referring to the.

Procedure





1. Prepare two or more keys to be programmed after the key ID number is cleared.

2. Connect the M-MDS to the DLC-2.

3. Using key 1, turn the ignition switch to the ON position.
NOTE:
- Although the security light starts flashing and DTC 15 or DTC 23 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

4. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

- When using the IDS (laptop PC)

- Select "Body".
- Select "Security".

- When using the PDS (Pocket PC)

- Select "Programming".

5. Then, select items from the screen menu in the following order.

- Select "PATS Functions".

6. Select "Parameter Reset" from the M-MDS screen menu and perform the procedure according to the M-MDS screen

7. Perform the security access according to the directions on the M-MDS screen. Procedures

8. Select the replaced parts according to the directions on the M-MDS.

- If the PCM is replaced: Select "PCM".
- If the keyless control module is replaced: Select "SKE".

NOTE:
- At this time, do not select the other parts from the M-MDS menu.

9. Select "Ignition Key Code Erase" from the M-MDS screen menu and perform the procedure according to the M-MDS screen.

CAUTION:
- The M-MDS displays "You must now program a minimum of two keys.", however, do not perform the key programming and proceed to Step 9. If the procedure is not followed, the engine may not be started. The key programming procedure is performed at Steps 14 to 19.

10. Perform the card key programming. Card Key ID Code Registration

11. Perform the steering lock unit programming. Steering Lock Unit ID Code Registration

12. After verifying that the PATS function menu is displayed again on the M-MDS screen, select "Exit (From This Menu)" to finish the M-MDS procedure.

13. After Step 12, wait 5 s or more and then turn the ignition switch to the ON position.

14. Ignition switch to the LOCK position.

15. Disconnect the M-MDS from the DLC-2.

16. Using key 1, turn the ignition switch to the ON position.

17. After verifying that the security light and keyless warning light illuminate for 3 s or more, turn the ignition switch to the LOCK position and remove key 1.
NOTE:
- Although the security light remains illuminated and DTC 21 is displayed after approx. 1 min, this does not indicate an improper procedure. Continue to perform the procedure as indicated.

18. Using key 2, turn the ignition switch to the ON position.

19. Verify that the security light and keyless warning light illuminate for approx. 3 s, and then goes out.

20. After verifying that the security light goes out, turn the ignition switch to the LOCK position using key 2, and then remove key 2.

21. If programming one more keys, repeat Steps 18 to 20 with a key to be programmed as key 3. If the vehicle is left with the ignition switch in the ON position for 1 min or more, additional key programming according to Steps 18 to 20 is disabled. If this occurs, refer to the "M-MDS connecting procedure" to program any additional keys.

22. Start the engine with key 1.

23. Verify that the security light and keyless warning light operate as follows:

- From the point when the ignition switch is turned to the ON position, the security light illuminates for approx. 3 s, and goes out.
- The keyless warning light illuminates when the ignition switch is turned to the ON position, and the light goes out after approx. 1 s, and then displays the number of the programmed keys.






24. After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position using key 1, and then remove the key.

25. Repeat Steps 22 to 24 using key 2 instead of key 1.
NOTE:
- If three or more keys have already been programmed, perform Steps 22 to 24.

26. Start the engine using the card key.

CAUTION:
- Remove any key from the key cylinder.
- Close all doors.
- Bring the card key into the vehicle.

27. Verify that the security light and keyless warning light operate as follows:

- From the point that ignition switch is turned to the ON position, the security light illuminates for approx. 3 s, and goes out.
- The keyless warning light illuminate when the ignition switch is turned to the ON position for approx. 1 min, and goes out.

28. After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position.

29. Verify that the all keys can start the engine for 5 s or more after the procedure.