| DTC |
DTC type (Euro4) |
DTC type (Except Euro4) |
DTC title |
Condition for running the DTC |
Condition for setting the DTC |
Action taken when DTC sets |
| P0016 |
A |
A |
DTC P0016 Crankshaft Position - Camshaft Position Correlation |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The CKP sensor signal pulses are detected. ・The CMP sensor signal pulses are detected. ・DTCs P0335, P0336, and P0340 are not set. |
・The ECM detects that the CKP sensor signal and the CMP sensor signal are not synchronized while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits engine startup. |
| P003A |
B |
B |
DTC P003A Turbocharger Boost Control Solenoid Performance |
・The ignition switch is ON. ・The battery voltage is 10 to 16 V. ・DTCs U0001, U0074, and U0110 are not set. |
・The ECM detects that the nozzle operating angle is too small or too large. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits the cruise control. |
| P0045 |
A |
A |
DTC P0045 Turbocharger Boost Control Solenoid Circuit |
・The ignition switch is ON. ・The battery voltage is 10 to 16 V. ・DTCs U0001, U0074, and U0110 are not set. |
・The ECM receives the turbocharger internal control unit circuit malfunction information. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0048 |
A |
A |
DTC P0048 Turbocharger Control Circuit High |
・The ignition switch is ON. ・The battery voltage is 10 to 16 V. ・DTCs U0001, U0074, and U0110 are not set. |
・The ECM detects that there is a short circuit in the turbocharger internal control circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0088 |
A |
A |
DTC P0088 Fuel Rail/System Pressure - Too High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0192, P0193, P060B, and P0651 are not set. |
・The ECM detects that the fuel rail pressure is 270 MPa {39,150 psi} or more for 2 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0089 |
B |
B |
DTC P0089 Fuel Pressure Regulator Performance |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・The engine coolant temperature is -35°C {-31°F} or more. ・The fuel temperature is 0°C {32°F} or more. ・DTCs P0192, P0193, P060B, and P0651 are not set. |
・The ECM detects that the actual fuel rail pressure is more than the desired fuel rail pressure by 40 MPa {5,800 psi} or more for 5 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits the EGR control. |
| P0090 |
A |
A |
DTC P0090 Fuel Pressure Regulator Solenoid Control Circuit Open |
・The battery voltage is 9 to 16 V. |
・The ECM detects a malfunction in the PCV circuit for 2 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P009B |
A |
A |
DTC P009B Common Rail Pressure Relief Valve Drive Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The FRP reduction valve is in operation. |
・The ECM detects a malfunction in the FRP reduction valve circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM stops pilot injection and pre-injection. ・The ECM inhibits the cruise control. |
| P0101 |
B |
B |
DTC P0101 Mass Air Flow Circuit Range/Performance |
・DTCs P003A, P0045, P0048, P0102, P0103, P0112, P0113, P0116, P0117, P0118, P0122, P0123, P0234, P0237, P0238, P0403, P0560, P060B, P0638, P0641, P0651, P0697, P1404, P2227, P2228, P2229, U0001, U0074, U010A, and U0110 are not set. Also, the following are met for 3 seconds or more: ・The battery voltage is 10 to 16 V. ・The ignition switch is ON. ・The intake air temperature is 110°C {230 °F} or less. ・The engine coolant temperature is -7 to 110°C {19 to 230°F}. ・The engine speed is 900 to 2400 rpm. ・The EGR control is commanded OFF. ・The intake throttle control is commanded OFF. ・The fuel injection control is commanded OFF. ・The accelerator pedal is not depressed. ・The engine runtime is 5 seconds or more. |
・The ECM detects that the MAF sensor signal voltage is not within the predetermined range for the calculated predicted MAF value. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). |
| P0102 |
A |
A |
DTC P0102 Mass Air Flow Circuit Low Input |
・The battery voltage is 10 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0560 and P060B are not set. |
・The ECM detects that the MAF sensor signal voltage is 0.1 V or less for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. ・The ECM assumes a default MAF value. |
| P0103 |
A |
A |
DTC P0103 Mass Air Flow Circuit High Input |
・The battery voltage is 10 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0560 and P060B are not set. |
・The ECM detects that the MAF sensor signal voltage is 4.9 V or more for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. ・The ECM assumes a default MAF value. |
| P0112 |
A |
A |
DTC P0112 Intake Air Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the IAT sensor signal voltage is 0.1 V or less for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default IAT value. |
| P0113 |
A |
A |
DTC P0113 Intake Air Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine runtime is 3 minutes or more. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the IAT sensor signal voltage is 4.85 V or more for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default IAT value. |
| P0116 |
B |
B |
DTC P0116 Engine Coolant Temperature Sensor Circuit Range/Performance |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The intake air temperature is 110°C {230 °F} or less. ・The vehicle driving time is 2 minutes or more. ・The engine speed is 1150 rpm or more for 2 minutes or more. ・The engine runtime is more than 6 minutes. ・DTCs P0117, P0118, P0201, P0202, P0203, P0204, P0500, P060B, P0697, P06AF, P1261, P2146, and P2149 are not set. |
・The ECM detects that the difference between the maximum and minimum engine coolant temperatures is 2.5°C {5°F} or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). |
| P0117 |
A |
A |
DTC P0117 Engine Coolant Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the engine coolant temperature sensor signal voltage is 0.1 V or less for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default engine coolant temperature value. |
| P0118 |
A |
A |
DTC P0118 Engine Coolant Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine runtime is 3 minutes or more. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the engine coolant temperature sensor signal voltage is 4.85 V or more for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default engine coolant temperature value. |
| P0122 |
A |
A |
DTC P0122 Throttle Position Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the intake throttle position sensor signal voltage is 0.3 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0123 |
A |
A |
DTC P0123 Throttle Position Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the intake throttle position sensor signal voltage is 4.9 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0182 |
A |
A |
DTC P0182 Fuel Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the fuel temperature sensor signal voltage is 0.1 V or less for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default fuel temperature value. |
| P0183 |
A |
A |
DTC P0183 Fuel Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine runtime is 3 minutes or more. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the fuel temperature sensor signal voltage is 4.85 V or more for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default fuel temperature value. |
| P0192 |
A |
A |
DTC P0192 Fuel Rail Pressure Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0651 are not set. |
・The ECM detects that the FRP sensor signal voltage is 0.3 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default fuel rail pressure value. |
| P0193 |
A |
A |
DTC P0193 Fuel Rail Pressure Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0651 are not set. |
・The ECM detects that the FRP sensor signal voltage is 4.75 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default fuel rail pressure value. |
| P0201 |
A |
A |
DTC P0201 Injector Circuit - Cylinder 1 |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0202 |
A |
A |
DTC P0202 Injector Circuit - Cylinder 2 |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0203 |
A |
A |
DTC P0203 Injector Circuit - Cylinder 3 |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0204 |
A |
A |
DTC P0204 Injector Circuit - Cylinder 4 |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0217 |
D |
D |
DTC P0217 Engine Coolant Over Temperature Condition |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0116, P0117, P0118, P060B, and P0697 are not set. |
・The ECM detects that the engine coolant temperature is 110°C {230°F} or more for 5 seconds. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). |
| P0219 |
D |
D |
DTC P0219 Engine Overspeed Condition |
- |
・The ECM detects that the engine speed is 5,000 rpm or more. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0234 |
A |
A |
DTC P0234 Turbocharger Overboost Condition |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P003A, P0045, P0048, P0237, P0238, P060B, P0651, U0001, U0074, and U0110 are not set. |
・The ECM detects that the actual boost pressure is higher than the desired boost pressure by 20 kPa {3 psi} or more for 10 seconds or more under a particular condition. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0237 |
A |
A |
DTC P0237 Turbocharger Boost Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0651 are not set. |
・The ECM detects that the boost pressure sensor signal voltage is 0.1 V or less for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default boost pressure value. |
| P0238 |
A |
A |
DTC P0238 Turbocharger Boost Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0651 are not set. |
・The ECM detects that the boost pressure sensor signal voltage is 4.9 V or more for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default boost pressure value. |
| P0299 |
B |
B |
DTC P0299 Turbocharger Underboost |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・The fuel injection quantity is more than or equal to the predetermined value. ・DTCs P003A, P0045, P0048, P0088, P0089, P0102, P0103, P0116, P0117, P0118, P0122, P0123, P0192, P0193, P0201, P0202, P0203, P0204, P0237, P0238, P0403, P0560, P060B, P0638, P0641, P0651, P0697, P06AF, P1093, P1261, P1404, P2146, P2149, P2227, P2228, P2229, U0001, U0074, U010A, and U0110 are not set. |
・The ECM detects that the actual boost pressure is less than the desired boost pressure by 40 kPa {6 psi} or more for 10 seconds or more under a particular condition. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0335 |
A |
A |
DTC P0335 Crankshaft Position Sensor Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The CMP sensor signal pulses are detected. ・DTCs P0016, P0336, and P0340 are not set. |
・The ECM detects that no CKP sensor signal pulse is generated while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0336 |
A |
A |
DTC P0336 Crankshaft Position Sensor Circuit Range/Performance |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The CKP sensor signal pulses are detected. ・DTCs P0016, P0335, and P0340 are not set. |
・The ECM detects excessive or short CKP sensor signal pulses while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0340 |
A |
A |
DTC P0340 Camshaft Position Sensor Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The CKP sensor signal pulses are detected. ・DTCs P0016, P0335, and P0336 are not set. |
・The ECM detects that no CMP sensor signal pulse is generated while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits engine startup. ・The ECM inhibits the cruise control. |
| P0380 |
C |
A |
DTC P0380 Glow Plug Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P1606 is not set. |
Any of the following are met: ・The ECM detects that there is an open circuit or a short to ground in the glow relay control circuit for 3 seconds or more when the relay is commanded OFF. ・The ECM detects that there is a short to the battery power supply circuit or a short to the ignition power supply circuit in the glow relay control circuit for 3 seconds or more when the relay is commanded ON. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0401 |
B |
B |
DTC P0401 Exhaust Gas Recirculation (EGR) Flow Insufficient Detected |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P003A, P0045, P0048, P0102, P0103, P0112, P0113, P0116, P0117, P0118, P0122, P0123, P0403, P0560, P060B, P0638, P0641, P0651, P0697, P2227, P2228, P2229, U0001, U0074, U010A, and U0110 are not set. |
・When the EGR control is in the feedback mode, the ECM detects that the EGR flow rate is low. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). |
| P0403 |
A |
A |
DTC P0403 Exhaust Gas Recirculation (EGR) Motor Control Circuit |
・The battery voltage is 10 to 16 V. ・DTCs U0074 and U010A are not set. |
・The ECM detects that a failure message from the EGR valve is being received. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0500 |
A |
A |
DTC P0500 Vehicle Speed Sensor |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The fuel injection is OFF with the accelerator pedal not depressed. ・The engine speed is 1000 rpm or more. ・DTC P0219 is not set. |
・The ECM detects that no vehicle speed signal pulse has been generated for 5 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. ・The ECM assumes a default vehicle speed value. |
| P0560 |
A |
A |
DTC P0560 System Voltage |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the voltage of the 12 V reference circuit is 7 V or less, or 16 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0563 |
C |
A |
DTC P0563 System Voltage High |
・DTC P060B is not set. |
・The ECM detects that the voltage of the ignition power supply circuit is 16 V or more for 5 seconds. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0565 |
C |
A |
DTC P0565 Cruise Control On Signal |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control main switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control main switch signal stays at the ON position (high voltage) for 15 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0566 |
C |
A |
DTC P0566 Cruise Control Off Signal |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control cancel switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control cancel switch signal stays at the ON position (low voltage) for 40 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0567 |
C |
A |
DTC P0567 Cruise Control Resume Signal |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control resume switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control resume switch signal stays at the ON position (low voltage) for 120 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0568 |
C |
A |
DTC P0568 Cruise Control Set Signal |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control set switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control set switch signal stays at the ON position (low voltage) for 120 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0571 |
C |
A |
DTC P0571 Brake Switch Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. |
Any of the following are met: ・The ECM detects a correlation error between the stoplight switch 1 signal and the stoplight switch 2 signal 32 times or more for 157 seconds or more. ・The ECM detects either the stoplight switch 1 signal or the stoplight switch 2 signal is ON for 15 minutes. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0601 |
A |
A |
DTC P0601 Internal Control Module Memory Check Sum Error |
- |
・The ECM detects that the calculated checksum does not match the checksum stored in the internal ROM. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM stops the engine. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0602 |
C |
A |
DTC P0602 Control Module Programming Error |
・DTC P1621 is not set. |
Any of the following are met: ・The ECM detects that the Injector ID Code is not programmed. ・The ECM detects an error in the programmed Injector ID Code. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0604 |
A |
A |
DTC P0604 Internal Control Module Random Access Memory (RAM) Error |
- |
・The ECM detects an internal RAM malfunction. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM stops the engine. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0606 |
A |
A |
DTC P0606 ECM/PCM Processor |
・The battery voltage is 8 V or more. |
・The ECM detects a malfunction in the internal main CPU or sub IC. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection (Main CPU malfunction). ・The ECM inhibits the cruise control. |
| P0607 |
A |
A |
DTC P0607 Internal Control Module Error (Cruise Cut) |
- |
・The ECM detects an abnormal calculated value due to the internal CPU. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P060B |
A |
A |
DTC P060B Internal Control Module A/D Processing Performance |
- |
・The ECM detects an internal A/D converter malfunction. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default barometric pressure value. ・The ECM assumes a default engine coolant temperature value. ・The ECM assumes a default fuel rail pressure value. ・The ECM assumes a default fuel temperature value. ・The ECM assumes a default idle up volume value. ・The ECM assumes a default IAT value. ・The ECM assumes a default MAF value. ・The ECM assumes a default boost pressure value. |
| P061A |
A |
A |
DTC P061A Control Module Torque Limitation Error |
- |
・The ECM detects an abnormal calculated value due to the internal CPU. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. |
| P0633 |
D |
D |
DTC P0633 Immobilizer Key Not Programmed - ECM/PCM |
・The ignition switch is ON. |
・The ECM detects that the immobilizer security information is not programmed. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| P0638 |
A |
A |
DTC P0638 Throttle Actuator Control Range/Performance |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The desired intake throttle valve opening position is stable. ・The intake throttle motor is commanded ON. ・DTCs P0122, P0123, P060B, and P0697 are not set. |
・The ECM detects that the difference between the actual intake throttle valve opening position and the desired valve opening position is 10% or more for 5 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0641 |
A |
A |
DTC P0641 Sensor Reference Voltage 1 Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the voltage of 5 V reference circuit 1 or 7 is 4.5 V or less, or 5.5 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0650 |
A |
A |
DTC P0650 Malfunction Indicator Lamp (MIL) Control Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. |
Any of the following are met: ・The ECM detects a low voltage condition in the MIL or check engine warning light control circuit when the light is commanded OFF. ・The ECM detects a high voltage condition in the MIL or check engine warning light control circuit when the light is commanded ON. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0651 |
A |
A |
DTC P0651 Sensor Reference Voltage 2 Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the voltage of 5 V reference circuit 2 or 8 is 4.5 V or less, or 5.5 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits engine startup. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default barometric pressure value. ・The ECM assumes a default fuel rail pressure value. ・The ECM assumes a default IAT value. |
| P0661 |
C |
A |
DTC P0661 Intake Manifold Tuning Valve Control Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・Swirl control valve is commanded OFF. ・DTC P1606 is not set. |
・When the solenoid is commanded OFF, the ECM detects a low voltage condition in the swirl control solenoid valve circuit. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0662 |
C |
A |
DTC P0662 Intake Manifold Tuning Valve Control Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・Swirl control valve is commanded ON. ・DTC P1606 is not set. |
・When the solenoid is commanded ON, the ECM detects a high voltage condition in the swirl control solenoid valve circuit. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0685 |
C |
A |
DTC P0685 ECM Power Relay Control Circuit/Open |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON for 3 seconds or more. ・DTC P060B is not set. |
・The ECM detects a low voltage condition in the ECM main relay voltage supply circuit for 3 seconds when the relay is commanded ON. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0687 |
C |
A |
DTC P0687 ECM Power Relay Control Circuit High |
- |
・The ECM detects that the ECM main relay turns ON when the relay is commanded OFF. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0697 |
A |
A |
DTC P0697 Sensor Reference Voltage 3 Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the voltage of 5 V reference circuit 3 or 9 is 4.5 V or less, or 5.5 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits engine startup. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. ・The ECM assumes a default barometric pressure value. ・The ECM assumes a default fuel rail pressure value. ・The ECM assumes a default IAT value. |
| P06AF |
A |
A |
DTC P06AF EDU (Electric Driver Unit) Injector Custom IC |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects an abnormal calculated value due to the internal CPU. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0700 |
A |
A |
DTC P0700 Transmission Control System (MIL Request) |
・The ignition switch is ON. ・DTCs U0001 and U0101 are not set. |
・The ECM detects that the TCM requests illumination of the MIL. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0807 |
C |
A |
DTC P0807 Clutch Position Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the clutch pedal stroke sensor signal voltage is 0.3 V or less. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0808 |
C |
A |
DTC P0808 Clutch Position Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0697 are not set. |
・The ECM detects that the clutch pedal stroke sensor signal voltage is 4.9 V or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P1093 |
B |
B |
DTC P1093 Fuel Rail Pressure (FRP) Too Low |
・The battery voltage is 9 to 16 V. ・The engine speed is 1200 rpm or more. ・The engine coolant temperature is 35°C {95°F} or more. ・The fuel temperature is 0 to 125°C {32 to 257°F} or more. ・DTCs P0192, P0193, P060B, P0651, P1267, and P228A are not set. |
・The ECM detects that the actual fuel rail pressure is less than the desired fuel rail pressure by 40 MPa {5,800 psi} or more for 5 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits the EGR control. |
| P124A |
A |
A |
DTC P124A Injector Charge Circuit high Voltage |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an excessive charge in the injector charge-up circuit in the ECM. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P1261 |
A |
A |
DTC P1261 Injector Charge Circuit Low Voltage |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an insufficient charge in the injector charge-up circuit in the ECM for 3 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P1267 |
A |
A |
DTC P1267 Common Rail Pressure Relief Valve Circuit 1 Low Voltage |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. |
・The ECM detects a low voltage malfunction in the PCV charge voltage circuit for 2 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P1269 |
A |
A |
DTC P1269 Common Rail Pressure Relief Valve Circuit High Voltage |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. |
・The ECM detects a high voltage malfunction in the PCV charge voltage circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P1404 |
A |
A |
DTC P1404 Exhaust Gas Recirculation (EGR) 1 Closed Position Performance |
Closed Position Error DTC ・The battery voltage is 10 to 16 V. ・The ignition switch is ON. ・The engine coolant temperature is 20 to 110°C {68 to 230°F}. ・The intake air temperature is 0 to 110°C {32 to 230°F}. ・The barometric pressure is 60 to 120 kPa {8.7 to 17.4 psi}. |
Closed Position Error DTC ・The ECM detects that the difference between the actual EGR valve opening position and the desired valve opening position is 20% or more for 11 seconds or more. Learned Position Error DTC ・The ECM detects that the EGR learned position is 10% or more or -10% or less when the ignition switch is OFF. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P1606 |
C |
A |
DTC P1606 ECM Internal IC Failure |
- |
・The ECM detects an internal IC malfunction. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P161B |
D |
D |
DTC P161B Immobilizer Wrong Response |
・The ignition switch is ON. |
・The ECM detects that an incorrect immobilizer response signal from the wireless access module is received. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| P1621 |
A |
A |
DTC P1621 Control Module Long Term Memory Performance |
- |
・The ECM detects an error in the learning data stored in the internal EEPROM. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P2122 |
A |
A |
DTC P2122 Pedal Position Sensor 1 Circuit Low Input |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0641 are not set. |
・The ECM detects that the accelerator pedal position sensor 1 signal voltage is 0.4 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2123 |
A |
A |
DTC P2123 Pedal Position Sensor 1 Circuit High Input |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0641 are not set. |
・The ECM detects that the accelerator pedal position sensor 1 signal voltage is 4.8 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2127 |
A |
A |
DTC P2127 Pedal Position Sensor 2 Circuit Low Input |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0651 are not set. |
・The ECM detects that the accelerator pedal position sensor 2 signal voltage is 0.4 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2128 |
A |
A |
DTC P2128 Pedal Position Sensor 2 Circuit High Input |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P060B and P0651 are not set. |
・The ECM detects that the accelerator pedal position sensor 2 signal voltage is 4.8 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2138 |
A |
A |
DTC P2138 Pedal Position Sensor 1 - 2 Voltage Correlation |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The accelerator pedal position sensor 1 signal voltage is 0.4 to 4.8 V. ・The accelerator pedal position sensor 2 signal voltage is 0.4 to 4.8 V. ・DTCs P060B, P0641, and P0651 are not set. |
・The ECM detects that accelerator pedal position sensors 1 and 2 deviate from the range by 30% or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2146 |
A |
A |
DTC P2146 Fuel Injector Group 1 Supply Voltage Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an open circuit, a short to ground, or a short to the voltage circuit in the common power supply 1 injector charge voltage circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P2149 |
A |
A |
DTC P2149 Fuel Injector Group 2 Supply Voltage Circuit |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. |
・The ECM detects that there is an open circuit, a short to ground, or a short to the voltage circuit in the common power supply 2 injector charge voltage circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P2227 |
B |
B |
DTC P2227 Barometric Pressure Circuit Range/Performance |
・The battery voltage is 9 to 16 V. ・The engine coolant temperature is -30°C {22°F} or more. ・The engine is stopped. ・The accelerator pedal is not depressed. ・The vehicle is stopped. ・DTCs P0102, P0103, P0112, P0113, P0116, P0117, P0118, P0122, P0123, P0237, P0238, P0403, P0500, P0560, P060B, P0638, P0641, P0651, P0697, P2228, P2229, U0074, and U010A are not set. |
・The ECM detects that the difference between the barometric pressure and the boost pressure is 10 kPa {1.5 psi} or more for 10 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. ・The ECM assumes a default barometric pressure value. |
| P2228 |
A |
A |
DTC P2228 Barometric Pressure Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the barometric pressure sensor signal voltage is 0.5 V or less for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default barometric pressure value. |
| P2229 |
A |
A |
DTC P2229 Barometric Pressure Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the barometric pressure sensor signal voltage is 4.0 V or more for 3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. ・The ECM assumes a default barometric pressure value. |
| P228A |
A |
A |
DTC P228A Common Rail Pressure Relief Valve IC Circuit Error |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・The FRP reduction valve is in operation. |
・The ECM detects a functional failure of the PCV control (IC) or the FRP reduction valve control (IC) for 3 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| U0001 |
A |
A |
DTC U0001 High Speed CAN Communication Bus |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON for 3 seconds or more. |
・The ECM detects a CAN Bus OFF status. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| U0074 |
A |
A |
DTC U0074 Control Module Communication Bus Off - Local CAN |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON for 3 seconds or more. |
・The ECM detects a CAN Bus OFF status. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. ・The ECM inhibits the turbocharger control. |
| U0101 |
A |
A |
DTC U0101 Lost Communication with TCM |
・The battery voltage is 9 V or more. ・The ignition switch is ON for 3 seconds or more. ・DTC U0001 is not set. |
・The ECM detects that the CAN messages from the TCM are not being received. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| U010A |
A |
A |
DTC U010A Lost Communication With Exhaust Gas Recirculation (EGR) Control Module |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC U0074 is not set. |
・The ECM detects that the CAN messages from the EGR valve are not being received. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| U0110 |
A |
A |
DTC U0110 Lost Communication with VNT System |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON for 3 seconds or more. ・DTCs U0001 and U0074 are not set. |
・The ECM detects that CAN messages from the turbocharger internal control unit are not received. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| U0167 |
D |
D |
DTC U0167 Lost Communication With Vehicle Immobilizer Control Module |
・The ignition switch is ON. |
・The ECM detects that an immobilizer response signal from the wireless access module is not received. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U023A |
C |
A |
DTC U023A Lost Communication with CAMERA Control Unit |
・The battery voltage is 8 to 16 V. ・The ignition switch is ON for 3 seconds or more. ・DTC U0001 is not set. |
・The ECM detects that CAN messages from the stereo camera are not received. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| U2300 |
D |
D |
DTC U2300 Immobilizer Ignition Line Off |
・The ignition switch is ON. |
・The ECM detects that the key authentication cannot be done because the wireless access module cannot detect the ignition switch ON signal. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U2301 |
D |
D |
DTC U2301 Immobilizer Transponder Authentication NG |
・The ignition switch is ON. |
The ECM receives an abnormal key authentication signal from the wireless access module 4 consecutive times due to any of the following conditions. ・The key authentication cannot be done because the wireless access module cannot receive a response signal from the transponder. ・The key authentication cannot be done because the wireless access module receives an incorrect response signal from the transponder. ・The key authentication cannot be done because the wireless access module receives an unknown response signal from the transponder. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U2302 |
D |
D |
DTC U2302 Immobilizer Anti-Scanning Mode |
・The ignition switch is ON. |
・The ECM receives a signal from the wireless access module which has transitioned to the anti-scan mode. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U2303 |
D |
D |
DTC U2303 Immobilizer Unknown Signal Received |
・The ignition switch is ON. |
・The ECM receives a response signal, which is outside the specifications, from the wireless access module. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |