Note
| DTC |
DTC type (Euro4) |
DTC type (Except Euro4) |
DTC title |
Condition for running the DTC |
Condition for setting the DTC |
Action taken when DTC sets |
| P0016 |
A |
A |
DTC P0016 (Flash code 16) Crankshaft Position - Camshaft Position Correlation |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The CKP sensor signal pulses are detected. ・The CMP sensor signal pulses are detected. ・DTCs P0335, P0336, and P0340 are not set. |
・The ECM detects that the CKP sensor signal and the CMP sensor signal are not synchronized while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits engine startup. |
| P0047 |
A |
A |
DTC P0047 (Flash Code 249) Turbocharger Boost Control Solenoid Circuit |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The duty ratio of the turbocharger control solenoid is 30% or more. ・DTC P060B is not set. |
Any of the following are met: ・The ECM detects that the feedback current of the turbocharger control solenoid is 70 mA or less for 3.2 seconds or more. ・The ECM detects that the feedback current of the turbocharger control solenoid is less than the desired current by 2,500 mA or more for 3.2 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0087 |
B |
B |
DTC P0087 (Flash Code 225) Fuel Rail/System Pressure - Too Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0192, P0193, P060B, and P0651 are not set. |
・The ECM detects that the fuel rail pressure is the predetermined value or more and the pressure limiter is activated. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits pre-injection. |
| P0088 |
A |
A |
DTC P0088 (Flash Code 118) Fuel Rail/System Pressure - Too High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・Rail pressure feedback mode is active. ・DTCs P0192, P0193, P060B, and P0651 are not set. |
・The ECM detects that the fuel rail pressure is the predetermined value or more for 2 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0089 |
B |
B |
DTC P0089 (Flash Code 151) Fuel Pressure Regulator Performance |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The intake air temperature is -40°C {-40°F} or more. ・The fuel temperature is -0.1°C {32°F} or more. ・The engine is running. ・Rail pressure feedback mode is active. ・DTCs P0091, P0092, P0112, P0113, P0182, P0183, P0192, P0193, P0201, P0202, P0203, P0204, P060B, P0651, and P1655 are not set. |
・The ECM detects that the difference between the actual fuel rail pressure and the desired fuel rail pressure is the predetermined value or more for 25 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits pre-injection. |
| P0091 |
A |
A |
DTC P0091 (Flash Code 247) Fuel Pressure Regulator Control Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
Any of the following are met: ・The ECM detects that the feedback current of the FRP regulator is 100 mA or less for 1.6 seconds or more. ・The ECM detects that the feedback current of the FRP regulator is less than the desired current by 1,000 mA or more for 1.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0092 |
A |
A |
DTC P0092 (Flash Code 247) Fuel Pressure Regulator Control Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
Any of the following are met: ・The ECM detects that the feedback current of the FRP regulator is 2,450 mA or more for 1.6 seconds or more. ・The ECM detects that the feedback current of the FRP regulator is more than the desired current by 1,000 mA or more for 1.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0093 |
B |
B |
DTC P0093 (Flash Code 227) Fuel System Leak Detected |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The intake air temperature is -40°C {-40°F} or more. ・The fuel temperature is -0.1°C {32°F} or more. ・The engine is running. ・Rail pressure feedback mode is active. ・DTCs P0087, P0091, P0092, P0112, P0113, P0192, P0193, P0201, P0202, P0203, P0204, P060B, and P0651 are not set. |
・The ECM detects that the actual fuel rail pressure is the predetermined value or less for 10 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits pre-injection. |
| P0097 |
C |
A |
DTC P0097 (Flash Code 214) Intake Manifold Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the CAC temperature sensor signal voltage is 0.17 V or less for 3 seconds. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0098 |
C |
A |
DTC P0098 (Flash Code 214) Intake Manifold Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・DTCs P0112, P0113, P060B, and P0651 are not set. |
・The ECM detects that the CAC temperature sensor signal voltage is 4.8 V or more for 3 seconds. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0101 |
B |
B |
DTC P0101 (Flash Code 92) Mass Air Flow Circuit Range/Performance |
・DTCs P0047, P0102, P0103, P0112, P0113, P0116, P0117, P0118, P0122, P0123, P0234, P0237, P0238, P02E3, P042E, P042F, P060B, P0638, P0651, P1655, P2227, P2228, P2229, and U0001 are not set. Also, the following are met for 2.9 seconds or more: ・The EGR control is commanded OFF. ・The battery voltage is 9 to 16 V. ・The accelerator pedal is not depressed. ・The engine is running. ・The fuel injection control is commanded OFF. ・The intake throttle control is commanded OFF. |
・The ECM detects that the difference between the actual MAF value and the predicted MAF value is not within the predetermined range for 7.9 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). |
| P0102 |
A |
A |
DTC P0102 (Flash Code 91) Mass Air Flow Circuit Low Input |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTC P060B is not set. |
・The ECM detects that the MAF sensor signal voltage is 0.1 V or less for 2.6 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default MAF value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P0103 |
A |
A |
DTC P0103 (Flash Code 91) Mass Air Flow Circuit High Input |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The engine is running. ・DTC P060B is not set. |
・The ECM detects that the MAF sensor signal voltage is 4.9 V or more for 2.6 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default MAF value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P0112 |
A |
A |
DTC P0112 (Flash Code 22) Intake Air Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the IAT sensor signal voltage is 0.1 V or less for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default IAT value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0113 |
A |
A |
DTC P0113 (Flash Code 22) Intake Air Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・3 minutes or more have passed since the engine was started. ・DTC P060B is not set. |
・The ECM detects that the IAT sensor signal voltage is 4.85 V or more for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default IAT value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0116 |
B |
B |
DTC P0116 (Flash Code 23) Engine Coolant Temperature Sensor Circuit Range/Performance |
・The battery voltage is 9 to 16 V. ・The fuel injection quantity is more than or equal to the predetermined value. ・The engine speed is 1,200 rpm or more. ・The vehicle speed is 0 km/h {0 mph} or more. ・DTCs P0117, P0118, P0201, P0202, P0203, P0204, P0500, P060B, and P1655 are not set. |
・The ECM detects that the difference between the maximum and minimum engine coolant temperatures is 5°C {9°F} or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM assumes a default engine coolant temperature value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0117 |
A |
A |
DTC P0117 (Flash Code 23) Engine Coolant Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the engine coolant temperature sensor signal voltage is 0.1 V or less for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default engine coolant temperature value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0118 |
A |
A |
DTC P0118 (Flash Code 23) Engine Coolant Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine runtime is 3 minutes or more. ・DTC P060B is not set. |
・The ECM detects that the engine coolant temperature sensor signal voltage is 4.85 V or more for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default engine coolant temperature value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0122 |
A |
A |
DTC P0122 (Flash Code 43) Throttle Position Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the intake throttle position sensor signal voltage is 0.3 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0123 |
A |
A |
DTC P0123 (Flash Code 43) Throttle Position Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the intake throttle position sensor signal voltage is 4.9 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0182 |
A |
A |
DTC P0182 (Flash Code 211) Fuel Temperature Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the fuel temperature sensor signal voltage is 0.1 V or less for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default fuel temperature value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0183 |
A |
A |
DTC P0183 (Flash Code 211) Fuel Temperature Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the fuel temperature sensor signal voltage is 4.85 V or more for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default fuel temperature value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits the turbocharger control. ・The ECM inhibits the cruise control. |
| P0192 |
A |
A |
DTC P0192 (Flash Code 245) Fuel Rail Pressure Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the FRP sensor signal voltage is 0.4 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default fuel rail pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0193 |
A |
A |
DTC P0193 (Flash Code 245) Fuel Rail Pressure Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the FRP sensor signal voltage is 4.75 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default fuel rail pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0201 |
A |
A |
DTC P0201 (Flash Code 271) Injector Circuit - Cylinder 1 |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0204, P06AF, P1261, and P2146 are not set. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 2.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P0202 |
A |
A |
DTC P0202 (Flash Code 272) Injector Circuit - Cylinder 2 |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0203, P06AF, P1262, and P2149 are not set. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 2.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P0203 |
A |
A |
DTC P0203 (Flash Code 273) Injector Circuit - Cylinder 3 |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0202, P06AF, P1262, and P2149 are not set. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 2.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0204 |
A |
A |
DTC P0204 (Flash Code 274) Injector Circuit - Cylinder 4 |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0201, P06AF, P1261, and P2146 are not set. |
・The ECM detects that there is an open circuit in the injector solenoid circuit for 2.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0217 |
D |
D |
DTC P0217 (Flash Code 542) Engine Coolant Over Temperature Condition |
・The battery voltage is 9 V or more. ・The ignition switch is ON. ・The engine is running. ・DTCs P0116, P0117, P0118, P060B, and P1655 are not set. |
・The ECM detects that the engine coolant temperature is 110°C {230°F} or more for 5 seconds. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). |
| P0219 |
D |
D |
DTC P0219 (Flash Code 543) Engine Overspeed Condition |
- |
・The ECM detects that the engine speed is 5,000 rpm or more. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0234 |
A |
A |
DTC P0234 (Flash Code 42) Turbocharger Overboost Condition |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0047, P0237, P0238, P060B, and P1655 are not set. |
・The ECM detects that the actual boost pressure is higher than the desired boost pressure by the predetermined value or more for 10 seconds or more under a particular condition. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0237 |
A |
A |
DTC P0237 (Flash Code 32) Turbocharger Boost Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P0122, P0123, P02E3, P060B, P0638, P0651, P1655, P2227, P2228, and P2229 are not set. |
・The ECM detects that the boost pressure sensor signal voltage is 0.1 V or less for 2.6 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default boost pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0238 |
A |
A |
DTC P0238 (Flash Code 32) Turbocharger Boost Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the boost pressure sensor signal voltage is 4.9 V or more for 2.6 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default boost pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P0299 |
B |
B |
DTC P0299 (Flash Code 65) Turbocharger Underboost |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P0047, P0087, P0088, P0089, P0091, P0092, P0093, P0102, P0103, P0116, P0117, P0118, P0122, P0123, P0192, P0193, P0201, P0202, P0203, P0204, P0237, P0238, P02E3, P042E, P042F, P060B, P0638, P0651, P1093, P1655, P2227, P2228, P2229, and U0001 are not set. |
・The ECM detects that the actual boost pressure is less than the desired boost pressure by the predetermined value or more for 10 seconds or more under a particular condition. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P02E3 |
A |
A |
DTC P02E3 (Flash Code 43) Intake Air Flow (IAF) Valve Control Circuit High Voltage |
・The battery voltage is 9 to 16 V. |
The ECM detects any of the following for 1.3 seconds or more. ・A short to ground in the intake throttle motor circuit ・A short to the battery power supply circuit or a short to the ignition power supply circuit in the intake throttle motor circuit |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P0335 |
A |
A |
DTC P0335 (Flash Code 15) Crankshaft Position Sensor Circuit |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The CMP sensor signal pulses are detected. ・DTCs P0336 and P0340 are not set. |
・The ECM detects that no CKP sensor signal pulse is generated while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0336 |
A |
A |
DTC P0336 (Flash Code 15) Crankshaft Position Sensor Circuit Range/Performance |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The CKP sensor signal pulses are detected. ・DTCs P0335 and P0340 are not set. |
・The ECM detects excessive or short CKP sensor signal pulses while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0340 |
A |
A |
DTC P0340 (Flash Code 14) Camshaft Position Sensor Circuit |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The CKP sensor signal pulses are detected. ・DTCs P0335 and P0336 are not set. |
・The ECM detects that no CMP sensor signal pulse is generated while the engine is running. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits engine startup. ・The ECM inhibits the cruise control. |
| P0380 |
C |
A |
DTC P0380 (Flash Code 66) Glow Plug Circuit |
・The battery voltage is 9 V or more. ・The ignition switch is ON. ・DTCs P0335, P0336, and P0340 are not set. |
Any of the following are met: ・The ECM detects a low voltage condition in the glow relay control circuit for 3 seconds or more when the relay is commanded OFF. ・The ECM detects a high voltage condition in the glow relay control circuit for 3 seconds or more when the relay is commanded ON. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0405 |
A |
A |
DTC P0405 (Flash Code 44) EGR Sensor Circuit Low |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the EGR position sensor signal voltage is 0.1 V or less for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0406 |
A |
A |
DTC P0406 (Flash Code 44) EGR Sensor Circuit High |
・The battery voltage is 9 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the EGR position sensor signal voltage is 4.9 V or more for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P042E |
A |
A |
DTC P042E (Flash Code 45) Exhaust Gas Recirculation (EGR) Closed Position Performance |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The desired EGR valve opening position is less than the predetermined value for 2 seconds or more. ・DTCs P0112, P0113, P0116, P0117, P0118, P0490, P060B, P0651, P1655, P2227, P2228, P2229, and U0001 are not set. |
・The ECM detects that the difference between the actual EGR valve opening position and the desired valve opening position is the predetermined value or more for 10 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P042F |
A |
A |
DTC P042F (Flash Code 45) Exhaust Gas Recirculation (EGR) Open Position Performance |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The desired EGR valve opening position is 20% or more. ・DTCs P0112, P0113, P0116, P0117, P0118, P0490, P060B, P0651, P1655, P2227, P2228, P2229, and U0001 are not set. |
・The ECM detects that the difference between the actual EGR valve opening position and the desired valve opening position is the predetermined value or more for 10 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0490 |
A |
A |
DTC P0490 (Flash Code 44) EGR Valve DC Motor Short to Battery |
・The battery voltage is 9 to 16 V. |
The ECM detects any of the following for 1.3 seconds or more. ・A short to ground in the EGR motor circuit ・A short to the battery power supply circuit or a short to the ignition power supply circuit in the EGR motor circuit |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0500 |
A |
A |
DTC P0500 (Flash Code 25) Vehicle Speed Sensor |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The fuel injection is in a non-injection state. ・The engine speed is 1,000 rpm or more. ・DTC P0219 is not set. |
・The ECM detects that no vehicle speed signal pulse has been generated for 5.1 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default vehicle speed value. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0563 |
C |
A |
DTC P0563 (Flash Code 35) System Voltage High |
・The battery voltage is 9 V or more. ・DTC P060B is not set. |
・The ECM detects that the voltage of the ignition power supply circuit is 16 V or more for 5 seconds. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0565 |
C |
A |
DTC P0565 (Flash Code 515) Cruise Control On Signal |
・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control main switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control main switch signal stays at the ON position (high voltage) for 15 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0566 |
C |
A |
DTC P0566 (Flash Code 516) Cruise Control Off Signal |
・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control cancel switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control cancel switch signal stays at the ON position (low voltage) for 40 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0567 |
C |
A |
DTC P0567 (Flash Code 517) Cruise Control Resume Signal |
・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control resume switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control resume switch signal stays at the ON position (low voltage) for 120 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0568 |
C |
A |
DTC P0568 (Flash Code 518) Cruise Control Set Signal |
・The ignition switch is ON. ・The engine is running. |
Any of the following are met: ・The ECM detects that the cruise control set switch signal continuously repeats ON and OFF within a very short adjustment time. ・The ECM detects that the cruise control set switch signal stays at the ON position (low voltage) for 120 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0571 |
C |
A |
DTC P0571 (Flash Code 26) Brake Switch Circuit |
・The ignition switch is ON. |
・The ECM detects a correlation error between the stoplight switch 1 signal and the stoplight switch 2 signal 32 times or more for 157 seconds or more. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0601 |
A |
A |
DTC P0601 (Flash Code 53) Internal Control Module Memory Check Sum Error |
・The checksum calculation has completed. |
・The ECM detects that the calculated checksum does not match the checksum stored in the internal ROM. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM stops the engine. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0602 |
C |
A |
DTC P0602 (Flash Code 154) Control Module Programming Error |
・The ignition switch is ON. |
Any of the following are met: ・The ECM detects that the Injector ID Code is not programmed. ・The ECM detects an error in the programmed Injector ID Code. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0604 |
A |
A |
DTC P0604 (Flash Code 153) Internal Control Module Random Access Memory (RAM) Error |
- |
・The ECM detects an internal RAM malfunction. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM stops the engine. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0606 |
A |
A |
DTC P0606 (Flash Code 51) ECM/PCM Processor |
・The battery voltage is 8 V or more. ・The ignition switch is ON. |
・The ECM detects a malfunction in the internal main CPU or sub IC. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P060B |
A |
A |
DTC P060B (Flash Code 36) Internal Control Module A/D Processing Performance |
- |
・The ECM detects an internal A/D converter malfunction. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default barometric pressure value. ・The ECM assumes a default engine coolant temperature value. ・The ECM assumes a default fuel rail pressure value. ・The ECM assumes a default fuel temperature value. ・The ECM assumes a default idle up volume value. ・The ECM assumes a default IAT value. ・The ECM assumes a default MAF value. ・The ECM assumes a default boost pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0633 |
D |
D |
DTC P0633 (Flash Code 176) Immobilizer Key Not Programmed - ECM/PCM |
- |
・The ECM detects that the immobilizer security information is not programmed. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| P0638 |
A |
A |
DTC P0638 (Flash Code 61) Throttle Actuator Control Range/Performance |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The intake throttle valve opening position is constant. ・The intake throttle motor duty ratio is the predetermined value or more. ・The intake throttle valve 0-point learning is not in progress. ・DTCs P0122, P0123, P02E3, P060B, and P1655 are not set. |
・The ECM detects that the difference between the actual intake throttle valve opening position and the desired valve opening position is the predetermined value or more for 5.1 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits pre-injection. ・The ECM inhibits the cruise control. |
| P0641 |
A |
A |
DTC P0641 (Flash Code 55) Sensor Reference Voltage 1 Circuit |
・The battery voltage is 8 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the voltage of 5 V reference circuit 1 is 4.5 V or less, or 5.5 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P0650 |
A |
A |
DTC P0650 (Flash Code 77) Malfunction Indicator Lamp (MIL) Control Circuit |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. |
Any of the following are met: ・The ECM detects a low voltage condition in the MIL control circuit when the MIL is commanded OFF. ・The ECM detects a high voltage condition in the MIL control circuit when the MIL is commanded ON. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0651 |
A |
A |
DTC P0651 (Flash Code 56) Sensor Reference Voltage 2 Circuit |
・The battery voltage is 8 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the voltage of 5 V reference circuit 2 or 5 is 4.5 V or less, or 5.5 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default barometric pressure value. ・The ECM assumes a default fuel rail pressure value. ・The ECM assumes a default IAT value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits engine startup. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0685 |
C |
A |
DTC P0685 (Flash Code 416) ECM Power Relay Control Circuit/Open |
・The battery voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects a low voltage condition in the ECM main relay voltage supply circuit for 3 seconds when the relay is commanded ON. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P0687 |
C |
A |
DTC P0687 (Flash Code 416) ECM Power Relay Control Circuit High |
・The ignition switch is OFF. ・DTC P0606 is not set. |
・The ECM detects that the ECM main relay turns ON when the relay is commanded OFF. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P06AF |
A |
A |
DTC P06AF (Flash Code 277) EDU (Electric Driver Unit) Injector Custom IC |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. |
・The ECM detects a functional failure of the injector control (IC) for 1.3 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P0700 |
A |
A |
DTC P0700 (Flash Code 185) Transmission Control System (MIL Request) |
・The ignition switch is ON. |
・The ECM detects that the TCM requests illumination of the MIL. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P1093 |
B |
B |
DTC P1093 (Flash Code 227) Fuel Rail Pressure (FRP) Too Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine coolant temperature is -40°C {-40°F} or more. ・The intake air temperature is -0.1°C {32°F} or more. ・The engine is running. ・Rail pressure feedback mode is active. ・DTCs P0087, P0112, P0113, P0182, P0183, P060B, P0651, and P1655 are not set. |
・The ECM detects that the actual fuel rail pressure is less than the desired fuel rail pressure by the predetermined value or more for 5.1 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM inhibits pre-injection. |
| P1261 |
A |
A |
DTC P1261 (Flash Code 34) Injector Positive Voltage Control Circuit Group 1 |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTC P06AF is not set. |
・The ECM detects a voltage malfunction in the common power supply 1 injector charge-up circuit in the ECM for 2.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P1262 |
A |
A |
DTC P1262 (Flash Code 34) Injector Positive Voltage Control Circuit Group 2 |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTC P06AF is not set. |
・The ECM detects a voltage malfunction in the common power supply 2 injector charge-up circuit in the ECM for 2.6 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P1404 |
A |
A |
DTC P1404 (Flash Code 45) Exhaust Gas Recirculation (EGR) 1 Closed Position Performance |
・The ignition switch is OFF. |
・The ECM detects that the actual 0-position is not within the range of the calculated 0-position during EGR valve learning. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| P1606 |
C |
A |
DTC P1606 (Flash Code 51) IO-IC 1 Communication line failure |
・The battery voltage is 8 to 16 V. |
・The ECM detects an internal circuit malfunction. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P161B |
D |
D |
DTC P161B (Flash Code 179) Immobilizer Wrong Response |
- |
・The ECM detects that an incorrect immobilizer response signal from the wireless access module is received. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| P1621 |
A |
A |
DTC P1621 (Flash Code 54) Control Module Long Term Memory Performance |
・The ignition switch is ON. |
・The ECM detects an error in the learning data stored in the internal EEPROM. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| P1655 |
A |
A |
DTC P1655 (Flash Code 59) Sensor Reference Voltage 4 Circuit |
・The battery voltage is 8 to 16 V. ・DTC P060B is not set. |
・The ECM detects that the voltage of 5 V reference circuit 4 is 4.5 V or less, or 5.5 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default engine coolant temperature value. ・The ECM assumes a default fuel temperature value. ・The ECM assumes a default boost pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the turbocharger control. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P2122 |
A |
A |
DTC P2122 (Flash Code 121) Pedal Position Sensor 1 Circuit Low Input |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the accelerator pedal position sensor 1 signal voltage is 0.4 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2123 |
A |
A |
DTC P2123 (Flash Code 121) Pedal Position Sensor 1 Circuit High Input |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the accelerator pedal position sensor 1 signal voltage is 4.8 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2127 |
A |
A |
DTC P2127 (Flash Code 122) Pedal Position Sensor 2 Circuit Low Input |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the accelerator pedal position sensor 2 signal voltage is 0.4 V or less. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2128 |
A |
A |
DTC P2128 (Flash Code 122) Pedal Position Sensor 2 Circuit High Input |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the accelerator pedal position sensor 2 signal voltage is 4.8 V or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2138 |
A |
A |
DTC P2138 (Flash Code 124) Pedal Position Sensor 1 - 2 Voltage Correlation |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The accelerator pedal position sensor 1 signal voltage is 0.4 to 4.8 V. ・The accelerator pedal position sensor 2 signal voltage is 0.4 to 4.8 V. ・DTC P060B is not set. |
・The ECM detects that the opening position difference between accelerator pedal position sensor 1 and accelerator pedal position sensor 2 is the predetermined value or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM inhibits the cruise control. |
| P2146 |
A |
A |
DTC P2146 (Flash Code 158) Fuel Injector Group 1 Supply Voltage Circuit |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0201, P0204, P06AF, and P1261 are not set. |
・The ECM detects that there is a short to ground or a short to the voltage circuit in the common power supply 1 injector charge voltage circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P2149 |
A |
A |
DTC P2149 (Flash Code 159) Fuel Injector Group 2 Supply Voltage Circuit |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・The engine is running. ・DTCs P0202, P0203, P06AF, and P1262 are not set. |
・The ECM detects that there is a short to ground, or a short to the voltage circuit in the common power supply 2 injector charge voltage circuit. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| P2227 |
B |
B |
DTC P2227 (Flash Code 71) Barometric Pressure Circuit Range/Performance |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTCs P0102, P0103, P0112, P0113, P0116, P0117, P0118, P0122, P0123, P0237, P0238, P02E3, P042E, P042F, P0500, P060B, P0638, P0651, P1655, P2228, P2229, and U0001 are not set. Also, the following are met for 3.1 seconds or more: ・The accelerator pedal is not depressed. ・The vehicle is stopped. ・The engine is idling. ・The fuel injection quantity is less than or equal to the predetermined value. ・The engine coolant temperature is 0°C {32°F} or more. |
・The ECM detects that the difference between the barometric pressure and the boost pressure is the predetermined value or more for 10.2 seconds or more. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type B (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type B (Except Euro4). ・The ECM assumes a default barometric pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P2228 |
A |
A |
DTC P2228 (Flash Code 71) Barometric Pressure Circuit Low |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the barometric pressure sensor signal voltage is 0.5 V or less for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default barometric pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| P2229 |
A |
A |
DTC P2229 (Flash Code 71) Barometric Pressure Circuit High |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. ・DTC P060B is not set. |
・The ECM detects that the barometric pressure sensor signal voltage is 4.0 V or more for 3.2 seconds. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM assumes a default barometric pressure value. ・The ECM limits the fuel injection quantity. ・The ECM inhibits pre-injection. ・The ECM inhibits the EGR control. ・The ECM inhibits the cruise control. |
| U0001 |
A |
A |
DTC U0001 (Flash Code 84) High Speed CAN Communication Bus |
・The battery voltage is 9 to 16 V. ・The ignition voltage is 9 to 16 V. ・The ignition switch is ON. |
・The ECM detects a CAN Bus OFF status. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM inhibits the cruise control. |
| U0101 |
A |
A |
DTC U0101 (Flash Code 85) Lost Communication with TCM |
・The battery voltage is 9 V or more. ・The ignition switch is ON. |
・The ECM detects that the CAN messages from the TCM are not being received. |
・Euro4: The ECM illuminates the MIL. Refer to Action taken when DTC sets - Type A (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). ・The ECM limits the fuel injection quantity. ・The ECM limits the fuel rail pressure. ・The ECM inhibits the cruise control. |
| U0167 |
D |
D |
DTC U0167 (Flash Code 177) Lost Communication with Vehicle Immobilizer Control Module |
- |
・The ECM detects that an immobilizer response signal from the wireless access module is not received. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U023A |
C |
A |
DTC U023A Lost Communication with CAMERA Control Unit |
・The battery voltage is 8 to 16 V. ・The ignition switch is ON for 3 seconds or more. ・DTC U0001 is not set. |
・The ECM detects that CAN messages from the stereo camera are not received. |
・Euro4: The ECM illuminates the SVS indicator light. Refer to Action taken when DTC sets - Type C (Euro4). ・Except Euro4: The ECM illuminates the check engine warning light. Refer to Action taken when DTC sets - Type A (Except Euro4). |
| U2300 |
D |
D |
DTC U2300 (Flash Code 181) Immobilizer Ignition Line Off |
- |
・The ECM detects that the key authentication cannot be done because the wireless access module cannot detect the ignition switch ON signal. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U2301 |
D |
D |
DTC U2301 (Flash Code 181) Immobilizer Transponder Authentication NG |
- |
The ECM receives an abnormal key authentication signal from the wireless access module 4 consecutive times due to any of the following conditions. ・The key authentication cannot be done because the wireless access module cannot receive a response signal from the transponder. ・The key authentication cannot be done because the wireless access module receives an incorrect response signal from the transponder. ・The key authentication cannot be done because the wireless access module receives an unknown response signal from the transponder. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U2302 |
D |
D |
DTC U2302 (Flash Code 181) Immobilizer Anti-Scanning Mode |
- |
・The ECM receives a signal from the wireless access module which has transitioned to the anti-scan mode. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |
| U2303 |
D |
D |
DTC U2303 (Flash Code 182) Immobilizer Unknown Signal Received |
- |
・The ECM receives a response signal, which is outside the specifications, from the wireless access module. |
・Euro4: The ECM does not illuminate the MIL or SVS indicator light. Refer to Action taken when DTC sets - Type D (Euro4). ・Except Euro4: The ECM does not illuminate the check engine warning light. Refer to Action taken when DTC sets - Type D (Except Euro4). ・The ECM inhibits engine startup. |