DTC P041C Exhaust Gas Recirculation (EGR) Temperature Sensor Circuit Low (4JJ3 with DPD)

1. Engine control system check

Refer to "51.Engine Control 1A.Troubleshooting(4JJ3 with DPD) Diagnostic system check-engine controls".

2. Prioritized DTC check

1) Connect the scan tool.

2) Turn OFF the ignition switch for 1 minute or more.

3) Start the engine.

4) Observe the DTC information with a scan tool. Is DTC P0697 set at the same time?

Yes

Go to DTC P0697 diagnosis.

Refer to "51.Engine Control 1A.Troubleshooting(4JJ3 with DPD) DTC P0697 Sensor Reference Voltage 3 Circuit".

No

=>Go to EGR gas temperature sensor 2 (EGR valve side) operation signal input check.

3. EGR gas temperature sensor 2 (EGR valve side) operation signal input check

1) Turn OFF the ignition switch for 1 minute or more.

2) Disconnect the EGR gas temperature sensor 2 (EGR valve side) harness connector (E92).

Refer to "RHD Engine Control (4JJ3 with DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "LHD Engine Control (4JJ3 with DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).

3) Start the engine.

4) Operate the vehicle under the conditions for running DTC P041D.

5) Observe the DTC information with a scan tool. Is DTC P041D set?

Yes

Replace EGR gas temperature sensor 2 (EGR valve side).

Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 with DPD) EGR gas temperature sensor 2 (EGR valve side) removal".

Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 with DPD) EGR gas temperature sensor 2 (EGR valve side) installation".

=>Go to DTC verification.

No

=>Go to Inspection for short to ground in EGR gas temperature sensor 2 (EGR valve side) signal circuit.

4. Inspection for short to ground in EGR gas temperature sensor 2 (EGR valve side) signal circuit

1) Inspect the signal circuit between the ECM (pin 24 of E1) and EGR gas temperature sensor 2 (EGR valve side) (pin 1 of E92) for the following. Is the result normal?

Refer to "RHD Engine Control (4JJ3 with DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "LHD Engine Control (4JJ3 with DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to ECM harness connector inspection.

No

Repair the circuit as necessary.

=>Go to Repair verification.

5. DTC verification

1) Clear the DTC with a scan tool.

2) Turn OFF the ignition switch for 1 minute or more.

3) Turn ON the ignition switch.

4) Observe the DTC information with a scan tool. Is a DTC set?

Yes

=>Go to ECM harness connector inspection.

No

=>Go to Repair verification.

6. ECM harness connector inspection

1) Inspect for poor connections at the ECM harness connector (pin 24 of E1, and pin 18 of E3). Is the connection status normal?

Refer to "RHD Engine Control (4JJ3 with DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "LHD Engine Control (4JJ3 with DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to ECM replacement.

No

Repair the connections as necessary.

=>Go to Repair verification.

7. ECM replacement

Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 with DPD) ECM removal".

Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 with DPD) ECM installation".

Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 with DPD) ECM setting".

Procedure completion

=>Go to Repair verification.

8. Repair verification

1) Clear the DTC with a scan tool.

2) Turn OFF the ignition switch for 1 minute or more.

3) Start the engine.

4) Operate the vehicle under the conditions for running the DTC.

5) Observe the DTC information with a scan tool.