| DTC |
DTC title |
Condition for running the DTC |
Condition for setting the DTC |
Action taken when DTC sets |
| B1021[56] |
DTC B1021[56] EOL Data Failure |
- |
・The BCM detects that the vehicle information has not been programmed. |
・Current and past failures are set. |
| B1053[03] |
DTC B1053[03] SRS Input Failure |
・The ignition switch is ON. |
・The BCM receives an invalid signal from the SRS control unit for 2 seconds or more. |
・Impact Sensing Door Unlock function becomes available only when the unlock request signal from the SRS is received via the CAN communication circuit. ・Current and past failures are set. |
| B110E[11] |
DTC B110E[11] RLS(Rain and Light Sensor) Circuit Short to Ground |
・The ignition switch is ON. |
Any of the following are met: ・The BCM detects a short to ground in the rain and light sensor ignition power supply circuit for 2.5 seconds or more. ・The BCM detects an overloading to the rain and light sensor ignition power supply circuit for 2 seconds or more. |
・If the light control switch is in the AUTO position, the headlight (low beam) illuminates. ・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B110E[49] |
DTC B110E[49] RLS(Rain and Light Sensor) Circuit Internal Electronic Failure |
・The ignition switch is ON. |
・The BCM detects an internal malfunction in the rain and light sensor ignition power supply circuit. |
・If the light control switch is in the AUTO position, the headlight (low beam) illuminates. ・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B110E[96] |
DTC B110E[96] RLS(Rain and Light Sensor) Circuit Component Internal Failure |
・The ignition switch is ON. |
・The BCM receives an error signal from the rain and light sensor for 3 seconds or more. |
・If the light control switch is in the AUTO position, the headlight (low beam) illuminates. ・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B110E[A2] |
DTC B110E[A2] RLS(Rain and Light Sensor) Circuit System Voltage Low |
・The ignition switch is ON. |
・The BCM detects a low voltage in the ignition power supply circuit for 3 seconds or more based on the sensor status received from the rain and light sensor. |
・If the light control switch is in the AUTO position, the headlight (low beam) illuminates. ・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B110E[A3] |
DTC B110E[A3] RLS(Rain and Light Sensor) Circuit System Voltage High |
- |
・The BCM detects a high voltage in the ignition power supply circuit for 3 seconds or more based on the sensor status received from the rain and light sensor. |
・If the light control switch is in the AUTO position, the headlight (low beam) illuminates. ・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B1312[11] |
DTC B1312[11] Steering Switch Input Circuit Short to Ground |
- |
・The BCM detects a short to ground in the cruise control switch input circuit for 2 seconds or more. |
・The cruise control switch does not operate normally. ・Current and past failures are set. |
| B1312[15] |
DTC B1312[15] Steering Switch Input Circuit Short to Battery or Open |
- |
・The BCM detects an open circuit or a short to the power supply in the cruise control switch input circuit for 2 seconds or more. |
・The cruise control switch does not operate normally. ・Current and past failures are set. |
| B1706[11] |
DTC B1706[11] Front/Rear Wiper Output Circuit Short to Ground |
・The ignition switch is ON. ・The BCM commands the front wiper relay ON. |
Any of the following are met: ・The BCM detects a short to ground in the front wiper relay drive circuit for 2.5 seconds or more. ・The BCM detects an overloading to the front wiper relay drive circuit for 2 seconds or more. |
・The output of the front wiper is stopped until the next command is given. ・Current and past failures are set. |
| B1706[12] |
DTC B1706[12] Front/Rear Wiper Output Circuit Short to Battery |
・The ignition switch is ON. Design blade type ・The BCM commands the front wiper H/L relay OFF. Flat blade type ・The BCM commands the washer relay OFF. |
Any of the following are met: Design blade type ・The BCM detects a short to the power supply in the front wiper H/L relay drive circuit for 2.5 seconds or more. ・The BCM detects an overloading to the front wiper H/L relay drive circuit for 2 seconds or more. Flat blade type ・The BCM detects a short to the power supply in the washer relay drive circuit for 2.5 seconds or more. ・The BCM detects an overloading to the washer relay drive circuit for 2 seconds or more. |
・The output of the front wiper is fixed in low until the next command is given. ・Current and past failures are set. |
| B1706[14] |
DTC B1706[14] Front/Rear Wiper Output Circuit Short to Ground or Open |
・The ignition switch is ON. ・The BCM commands the front wiper H/L relay OFF. |
・The BCM detects an open circuit or a short to ground in the front wiper H/L relay drive circuit for 2 seconds or more. |
・The control of the front wiper by the BCM is stopped. ・Current and past failures are set. |
| B1706[15] |
DTC B1706[15] Front Wiper Output Circuit Short to Battery or Open |
・The ignition switch is ON. ・The BCM commands the front wiper relay ON. |
・The BCM detects an open circuit or a short to the power supply in the front wiper relay drive circuit for 2 seconds or more. |
・The control of the front wiper by the BCM is stopped. ・Current and past failures are set. |
| B1706[49] |
DTC B1706[49] Front/Rear Wiper Output Circuit Internal Electronic Failure |
・The ignition switch is ON. ・The BCM commands the front wiper relay or front wiper H/L relay OFF. |
Any of the following are met: ・The BCM detects an internal malfunction in the front wiper relay drive circuit in the BCM. ・The BCM detects an internal malfunction in the front wiper H/L relay drive circuit in the BCM. |
・The output of the front wiper is stopped. ・The output of the front wiper is fixed in low until the DTC is cleared. ・Current and past failures are set. |
| B1706[96] |
DTC B1706[96] Front Wiper Output Circuit Component Internal Failure |
- |
・The BCM receives an error signal from the wiper motor for 3 seconds or more. |
・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B1706[98] |
DTC B1706[98] Front Wiper Output Circuit Component or System Over Temperature |
- |
・The BCM receives a high temperature abnormal signal from the wiper motor for 3 seconds or more. |
・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B1706[A2] |
DTC B1706[A2] Front Wiper Output Circuit System Voltage Low |
- |
・The BCM receives the signal of the ignition power supply circuit low voltage from the wiper motor for 3 seconds or more. |
・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B1706[A3] |
DTC B1706[A3] Front Wiper Output Circuit System Voltage High |
- |
・The BCM receives the signal of the ignition power supply circuit high voltage from the wiper motor for 3 seconds or more. |
・If a malfunction is detected during the automatic wiper operation, the wiper is continuously controlled with the wiper request sent before the malfunction is detected. ・If the ignition switch is turned OFF or if the windshield wiper switch is set to the AUTO position again after a malfunction is detected during the automatic wiper operation, the wiper is intermittently controlled. ・Current and past failures are set. |
| B1707[11] |
DTC B1707[11] Door Lock / Unlock Output Circuit Short to Ground |
- |
Any of the following are met: ・The BCM detects a short to ground in the door lock motor (lock) drive circuit. ・The BCM detects a short to ground in the door lock motor (unlock) drive circuit. |
・Current and past failures are set. |
| B1709[11] |
DTC B1709[11] Interior Light Output Circuit Short to Ground |
・The ignition switch is ON. ・The interior light battery saver function is not in operation. |
Any of the following are met: ・The BCM detects a short to ground in the interior light High side output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the interior light High side output circuit for 2 seconds or more. |
・The output of the interior light is stopped until the next command is given. ・Current and past failures are set. |
| B1709[12] |
DTC B1709[12] Interior Light Output Circuit Short to Battery |
・The BCM commands the interior light ON. |
Any of the following are met: ・The BCM detects a short to the power supply in the interior light Low side output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the interior light Low side output circuit for 2 seconds or more. |
・The output of the interior light is stopped. ・Current and past failures are set. |
| B1709[13] |
DTC B1709[13] Interior Light Output Circuit Open |
・The BCM commands the ambient light OFF. |
Any of the following is met: ・The BCM detects a short to the power supply in the ambient light output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the ambient light output circuit for 2 seconds or more. |
・The output of the ambient light is stopped. ・Current and past failures are set. |
| B1709[49] |
DTC B1709[49] Interior Light Output Circuit Internal Electronic Failure |
・The BCM commands the interior light ON. |
Any of the following are met: ・The BCM detects an internal malfunction in the interior light High side output circuit. ・The BCM detects an internal malfunction in the interior light Low side output circuit. |
・When there is a malfunction in the interior light High side output circuit, the output of the interior light High side is stopped. ・When there is a malfunction in the interior light Low side output circuit, the output of the interior light Low side is stopped. ・Current and past failures are set. |
| B1718[11] |
DTC B1718[11] Anti-theft System Indicator Light Output Circuit Short to Ground |
・The BCM commands the anti-theft system indicator light ON. |
・The BCM detects a short to ground in the anti-theft system indicator light output circuit for 2 seconds or more. |
・The anti-theft system indicator light turns OFF. ・Current and past failures are set. |
| B1718[12] |
DTC B1718[12] Anti-theft System Indicator Light Output Circuit Short to Battery |
・The BCM commands the anti-theft system indicator light OFF. |
・The BCM detects a short to the power supply in the anti-theft system indicator light output circuit for 2 seconds or more. |
・The anti-theft system indicator light illuminates. ・Current and past failures are set. |
| B1718[49] |
DTC B1718[49] Anti-theft System Indicator Light Output Circuit Internal Electronic Failure |
・The BCM commands the anti-theft system indicator light ON. |
・The BCM detects an internal malfunction in the anti-theft system indicator light output circuit. |
・The anti-theft system indicator light turns OFF. ・Current and past failures are set. |
| B1719[12] |
DTC B1719[12] Rear Defogger Output Circuit Short to Battery |
・The BCM commands the rear defogger relay OFF. |
・The BCM detects a short to the power supply in the rear defogger relay drive circuit for 2.5 seconds or more. ・The BCM detects an overloading to the rear defogger relay drive circuit for 2 seconds or more. |
・The rear defogger does not operate normally. ・Current and past failures are set. |
| B1719[14] |
DTC B1719[14] Rear Defogger Output Circuit Short to Ground |
・The BCM commands the rear defogger relay ON. |
・The BCM detects an open circuit or a short to ground in the rear defogger relay drive circuit for 2 seconds or more. |
・The control of the rear defogger by the BCM is stopped. ・Current and past failures are set. |
| B1719[49] |
DTC B1719[49] Rear Defogger Output Circuit Internal Electronic Failure |
・The BCM commands the rear defogger relay ON. |
・The BCM detects an internal malfunction in the rear defogger relay drive circuit. |
・The rear defogger does not operate normally. ・Current and past failures are set. |
| B171A[49] |
DTC B171A[49] BSI(Blind Spot Indicator) RH Circuit Internal Electronic Failure |
・The blind spot indicator function is in operation. |
・The BCM detects an internal malfunction in the blind spot indicator (right) output circuit. |
・The output of the blind spot indicator (right) is stopped. ・Current and past failures are set. |
| B171B[49] |
DTC B171B[49] BSI(Blind Spot Indicator) LH Circuit Internal Electronic Failure |
・The blind spot indicator function is in operation. |
・The BCM detects an internal malfunction in the blind spot indicator (left) output circuit. |
・The output of the blind spot indicator (left) is stopped. ・Current and past failures are set. |
| C0023[11] |
DTC C0023[11] Stop Light Output Circuit Short to Ground |
・The BCM commands the stop light ON. |
Any of the following are met: ・The BCM detects a short to ground in the stop light (right) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the stop light (right) output circuit for 2 seconds or more. ・The BCM detects a short to ground in the stop light (left) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the stop light (left) output circuit for 2 seconds or more. |
・When there is a malfunction in the stop light (right) output circuit, the output of the stop light (right) is stopped until the next command is given. ・When there is a malfunction in the stop light (left) output circuit, the output of the stop light (left) is stopped until the next command is given. ・Current and past failures are set. |
| C0023[12] |
DTC C0023[12] Stop Light Output Circuit Short to Battery |
・The BCM commands the stop light OFF. |
Any of the following are met: ・The BCM detects a short to the power supply in the stop light (right) output circuit for 2.5 seconds or more. ・The BCM detects a short to the power supply in the stop light (left) output circuit for 2.5 seconds or more. |
・When there is a malfunction in the stop light (right) output circuit, the output of the stop light (right) is turned ON regardless of the input stop light switch signal. ・When there is a malfunction in the stop light (left) output circuit, the output of the stop light (left) is turned ON regardless of the input stop light switch signal. ・Current and past failures are set. |
| C0023[49] |
DTC C0023[49] Stop Light Output Circuit Internal Electronic Failure |
・The BCM commands the stop light ON. |
Any of the following are met: ・The BCM detects an internal malfunction in the stop light (right) output circuit. ・The BCM detects an internal malfunction in the stop light (left) output circuit. |
・When there is a malfunction in the stop light (right) output circuit, the output of the stop light (right) is stopped. ・When there is a malfunction in the stop light (left) output circuit, the output of the stop light (left) is stopped. ・Current and past failures are set. |
| C1706[12] |
DTC C1706[12] Rear Fog Lamp Output Circuit Short to Battery |
・The BCM commands the rear fog light relay OFF. |
Any of the following are met: ・The BCM detects a short to the power supply in the rear fog light relay drive circuit for 2.5 seconds or more. ・The BCM detects an overloading to the rear fog light relay drive circuit for 2 seconds or more. |
・The rear fog light does not operate normally. ・Current and past failures are set. |
| C1706[14] |
DTC C1706[14] Rear Fog Lamp Output Circuit Open or Short to Ground |
・The BCM commands the rear fog light relay ON. |
・The BCM detects an open circuit or a short to ground in the rear fog light relay drive circuit for 2 seconds or more. |
・The control of the rear fog light by the BCM is stopped. ・Current and past failures are set. |
| C1706[49] |
DTC C1706[49] Rear Fog Lamp Output Circuit Internal Electronic Failure |
・The BCM commands the rear fog light relay ON. |
・The BCM detects an internal malfunction in the rear fog light relay drive circuit. |
・The rear fog light relay drive is stopped. ・Current and past failures are set. |
| C1707[11] |
DTC C1707[11] Backup Light Circuit Short to Ground |
・The BCM commands the back up light ON. |
Any of the following are met: ・The BCM detects a short to ground in the back up light output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the back up light output circuit for 2 seconds or more. |
・The output of the back up light is stopped until the next command is given. ・Current and past failures are set. |
| C1707[12] |
DTC C1707[12] Backup Light Circuit Short to Battery |
・The BCM commands the back up light OFF. |
・The BCM detects a short to the power supply in the back up light output circuit for 2.5 seconds or more. |
・The output of the back up light is turned ON regardless of the input reverse signal. ・Current and past failures are set. |
| C1707[13] |
DTC C1707[13] Backup Light Circuit Open |
・The BCM commands the back up light OFF. |
・The BCM detects an open circuit in the back up light output circuit for 2 seconds or more. |
・The output of the back up light is stopped. ・Current and past failures are set. |
| C1707[49] |
DTC C1707[49] Backup Light Circuit Internal Electronic Failure |
・The BCM commands the back up light ON. |
・The BCM detects an internal malfunction in the back up light output circuit. |
・The output of the back up light is stopped. ・Current and past failures are set. |
| C1720[11] |
DTC C1720[11] Front Right Turn Signal Light Output Circuit Short to Ground |
・The BCM commands the turn signal light (front right) ON. |
・The BCM detects a short to ground or an overloading to the turn signal light (front right) output circuit. |
・The output of the turn signal light (front right) is stopped until the next command is given. ・Current and past failures are set. |
| C1720[12] |
DTC C1720[12] Front Right Turn Signal Light Output Circuit Short to Battery |
・The BCM commands the turn signal light (front right) OFF. |
・The BCM detects a short to the power supply in the turn signal light (front right) output circuit. |
・The output of the turn signal light (front right) is turned ON regardless of the input turn signal switch signal or hazard warning flasher switch signal. ・Current and past failures are set. |
| C1720[13] |
DTC C1720[13] Front Right Turn Signal Light Output Circuit Open |
・The BCM commands the turn signal light (front right) ON. |
・The BCM detects an open circuit in the turn signal light (front right) output circuit. |
・The output of the turn signal light (front right) is stopped. ・Current and past failures are set. |
| C1720[49] |
DTC C1720[49] Front Right Turn Signal Light Output Circuit Internal Electronic Failure |
・The BCM commands the turn signal light (front right) ON. |
・The BCM detects an internal malfunction in the turn signal light (front right) output circuit. |
・The output of the turn signal light (front right) is stopped. ・Current and past failures are set. |
| C1721[11] |
DTC C1721[11] Front Left Turn Signal Light Output Circuit Short to Ground |
・The BCM commands the turn signal light (front left) ON. |
・The BCM detects a short to ground or an overloading to the turn signal light (front left) output circuit. |
・The output of the turn signal light (front left) is stopped until the next command is given. ・Current and past failures are set. |
| C1721[12] |
DTC C1721[12] Front Left Turn Signal Light Output Circuit Short to Battery |
・The BCM commands the turn signal light (front left) OFF. |
・The BCM detects a short to the power supply in the turn signal light (front left) output circuit. |
・The output of the turn signal light (front left) is turned ON regardless of the input turn signal switch signal or hazard warning flasher switch signal. ・Current and past failures are set. |
| C1721[13] |
DTC C1721[13] Front Left Turn Signal Light Output Circuit Open |
・The BCM commands the turn signal light (front left) ON. |
・The BCM detects an open circuit in the turn signal light (front left) output circuit. |
・The output of the turn signal light (front left) is stopped. ・Current and past failures are set. |
| C1721[49] |
DTC C1721[49] Front Left Turn Signal Light Output Circuit Internal Electronic Failure |
・The BCM commands the turn signal light (front left) ON. |
・The BCM detects an internal malfunction in the turn signal light (front left) output circuit. |
・The output of the turn signal light (front left) is stopped. ・Current and past failures are set. |
| C1722[11] |
DTC C1722[11] Side Right Turn Signal Light Output Circuit Short to Ground |
・The BCM commands the side turn signal light (right) ON. |
・The BCM detects a short to ground or an overloading to the side turn signal light (right) output circuit. |
・The output of the side turn signal light (right) is stopped until the next command is given. ・Current and past failures are set. |
| C1722[12] |
DTC C1722[12] Side Right Turn Signal Light Output Circuit Short to Battery |
・The BCM commands the side turn signal light (right) OFF. |
・The BCM detects a short to the power supply in the side turn signal light (right) output circuit. |
・The output of the side turn signal light (right) is turned ON regardless of the input turn signal switch signal or hazard warning flasher switch signal. ・Current and past failures are set. |
| C1722[13] |
DTC C1722[13] Side Right Turn Signal Light Output Circuit Open |
・The BCM commands the side turn signal light (right) ON. |
・The BCM detects an open circuit in the side turn signal light (right) output circuit. |
・The output of the side turn signal light (right) is stopped. ・Current and past failures are set. |
| C1722[49] |
DTC C1722[49] Side Right Turn Signal Light Output Circuit Internal Electronic Failure |
・The BCM commands the side turn signal light (right) OFF. |
・The BCM detects an internal malfunction in the side turn signal light (right) output circuit. |
・The output of the side turn signal light (right) is stopped. ・Current and past failures are set. |
| C1723[11] |
DTC C1723[11] Side Left Turn Signal Light Output Circuit Short to Ground |
・The BCM commands the side turn signal light (left) ON. |
・The BCM detects a short to ground or an overloading to the side turn signal light (left) output circuit. |
・The output of the side turn signal light (left) is stopped until the next command is given. ・Current and past failures are set. |
| C1723[12] |
DTC C1723[12] Side Left Turn Signal Light Output Circuit Short to Battery |
・The BCM commands the side turn signal light (left) OFF. |
・The BCM detects a short to the power supply in the side turn signal light (left) output circuit. |
・The output of the side turn signal light (left) is turned ON regardless of the input turn signal switch signal or hazard warning flasher switch signal. ・Current and past failures are set. |
| C1723[13] |
DTC C1723[13] Side Left Turn Signal Light Output Circuit Open |
・The BCM commands the side turn signal light (left) ON. |
・The BCM detects an open circuit in the side turn signal light (left) output circuit. |
・The output of the side turn signal light (left) is stopped. ・Current and past failures are set. |
| C1723[49] |
DTC C1723[49] Side Left Turn Signal Light Output Circuit Internal Electronic Failure |
・The BCM commands the side turn signal light (left) OFF. |
・The BCM detects an internal malfunction in the side turn signal light (left) output circuit. |
・The output of the side turn signal light (left) is stopped. ・Current and past failures are set. |
| C1724[11] |
DTC C1724[11] Rear Right Turn Signal Light Output Circuit Short to Ground |
・The BCM commands the turn signal light (rear right) ON. |
・The BCM detects a short to ground or an overloading to the turn signal light (rear right) output circuit. |
・The output of the turn signal light (rear right) is stopped until the next command is given. ・Current and past failures are set. |
| C1724[12] |
DTC C1724[12] Rear Right Turn Signal Light Output Circuit Short to Battery |
・The BCM commands the turn signal light (rear right) OFF. |
・The BCM detects a short to the power supply in the turn signal light (rear right) output circuit. |
・The output of the turn signal light (rear right) is turned ON regardless of the input turn signal switch signal or hazard warning flasher switch signal. ・Current and past failures are set. |
| C1724[13] |
DTC C1724[13] Rear Right Turn Signal Light Output Circuit Open |
・The BCM commands the turn signal light (rear right) ON. |
・The BCM detects an open circuit in the turn signal light (rear right) output circuit. |
・The output of the turn signal light (rear right) is stopped. ・Current and past failures are set. |
| C1724[49] |
DTC C1724[49] Rear Right Turn Signal Light Output Circuit Internal Electronic Failure |
・The BCM commands the turn signal light (rear right) OFF. |
・The BCM detects an internal malfunction in the turn signal light (rear right) output circuit. |
・The output of the turn signal light (rear right) is stopped. ・Current and past failures are set. |
| C1724[96] |
DTC C1724[96] Rear Right Turn Signal Light Output Circuit Component Internal |
・The BCM detects that the trailer is connected. |
・ BCM receives an error signal from the trailer side for 2 seconds or more via the trailer module feedback signal (right) circuit. |
・Current and past failures are set. |
| C1725[11] |
DTC C1725[11] Rear Left Turn Signal Light Output Circuit Short to Ground |
・The BCM commands the turn signal light (rear left) ON. |
・The BCM detects a short to ground or an overloading to the turn signal light (rear left) output circuit. |
・The output of the turn signal light (rear left) is stopped until the next command is given. ・Current and past failures are set. |
| C1725[12] |
DTC C1725[12] Rear Left Turn Signal Light Output Circuit Short to Battery |
・The BCM commands the turn signal light (rear left) OFF. |
・The BCM detects a short to the power supply in the turn signal light (rear left) output circuit. |
・The output of the turn signal light (rear left) is turned ON regardless of the input turn signal switch signal or hazard warning flasher switch signal. ・Current and past failures are set. |
| C1725[13] |
DTC C1725[13] Rear Left Turn Signal Light Output Circuit Open |
・The BCM commands the turn signal light (rear left) ON. |
・The BCM detects an open circuit in the turn signal light (rear left) output circuit. |
・The output of the turn signal light (rear left) is stopped. ・Current and past failures are set. |
| C1725[49] |
DTC C1725[49] Rear Left Turn Signal Light Output Circuit Internal Electronic Failure |
・The BCM commands the turn signal light (rear left) OFF. |
・The BCM detects an internal malfunction in the turn signal light (rear left) output circuit. |
・The output of the turn signal light (rear left) is stopped. ・Current and past failures are set. |
| C1725[96] |
DTC C1725[96] Rear Left Turn Signal Light Output Circuit Component Internal Failure |
・The BCM detects that the trailer is connected. |
・ BCM receives an error signal from the trailer side for 2 seconds or more via the trailer module feedback signal (left) circuit. |
・Current and past failures are set. |
| C1726[11] |
DTC C1726[11] Right Head Light (Low Beam) Output Circuit Short to Ground |
・The BCM commands the headlight (right) low beam ON. |
Any of the following are met: ・The BCM detects a short to ground in the headlight (right) low beam output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the headlight (right) low beam output circuit for 2 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) low beam is stopped until the next command is given. ・Current and past failures are set. |
| C1726[12] |
DTC C1726[12] Right Head Light (Low Beam) Output Circuit Short to Battery |
・The BCM commands the headlight (right) low beam OFF. |
・The BCM detects a short to the power supply in the headlight (right) low beam output circuit for 2.5 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) low beam is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C1726[13] |
DTC C1726[13] Right Head Light (Low Beam) Output Circuit Open |
・The BCM commands the headlight (right) low beam ON. |
・The BCM detects an open circuit in the headlight (right) low beam output circuit for 2 seconds or more. |
・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) low beam is stopped. ・Current and past failures are set. |
| C1726[49] |
DTC C1726[49] Right Head Light (Low Beam) Output Circuit Internal Electronic Failure |
・The BCM commands the headlight (right) low beam ON. |
・The BCM detects an internal malfunction in the headlight (right) low beam output circuit. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) low beam is stopped. ・Current and past failures are set. |
| C1726[96] |
DTC C1726[96] Right Head Light (Low Beam) Output Circuit Component Internal Failure |
・The BCM commands the headlight (right) low beam ON. |
・The BCM receives an error signal of the LED headlight (right) low beam for 2 seconds or more. |
・The LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the LED headlight (right) low beam is stopped. ・Current and past failures are set. |
| C1727[11] |
DTC C1727[11] Left Head Light (Low Beam) Output Circuit Short to Ground |
・The BCM commands the headlight (left) low beam ON. |
Any of the following are met: ・The BCM detects a short to ground in the headlight (left) low beam output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the headlight (left) low beam output circuit for 2 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) low beam is stopped until the next command is given. ・Current and past failures are set. |
| C1727[12] |
DTC C1727[12] Left Head Light (Low Beam) Output Circuit Short to Battery |
・The BCM commands the headlight (left) low beam OFF. |
・The BCM detects a short to the power supply in the headlight (left) low beam output circuit for 2.5 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) low beam is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C1727[13] |
DTC C1727[13] Left Head Light (Low Beam) Output Circuit Open |
・The BCM commands the headlight (left) low beam ON. |
・The BCM detects an open circuit in the headlight (left) low beam output circuit for 2 seconds or more. |
・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) low beam is stopped. ・Current and past failures are set. |
| C1727[49] |
DTC C1727[49] Left Head Light (Low Beam) Output Circuit Internal Electronic Failure |
・The BCM commands the headlight (left) low beam ON. |
・The BCM detects an internal malfunction in the headlight (left) low beam output circuit. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) low beam is stopped. ・Current and past failures are set. |
| C1727[96] |
DTC C1727[96] Left Head Light (Low Beam) Output Circuit Component Internal Failure |
・The BCM commands the headlight (left) low beam ON. |
・The BCM receives an error signal of the LED headlight (left) low beam for 2 seconds or more. |
・The LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the LED headlight (left) low beam is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C1728[11] |
DTC C1728[11] Right Head Light (High Beam) Output Circuit Short to Ground |
・The BCM commands the headlight (right) high beam ON. |
Any of the following are met: ・The BCM detects a short to ground in the headlight (right) high beam output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the headlight (right) high beam output circuit for 2 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) high beam is stopped until the next command is given. ・Current and past failures are set. |
| C1728[12] |
DTC C1728[12] Right Head Light (High Beam) Output Circuit Short to Battery |
・The BCM commands the headlight (right) high beam OFF. |
・The BCM detects a short to the power supply in the headlight (right) high beam output circuit for 2.5 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) high beam is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C1728[13] |
DTC C1728[13] Right Head Light (High Beam) Output Circuit Open |
・The BCM commands the headlight (right) high beam OFF. |
・The BCM detects an open circuit in the headlight (right) high beam output circuit for 2 seconds or more. |
・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) high beam is stopped. ・Current and past failures are set. |
| C1728[49] |
DTC C1728[49] Right Head Light (High Beam) Output Circuit Internal Electronic Failure |
・The BCM commands the headlight (right) high beam ON. |
・The BCM detects an internal malfunction in the headlight (right) high beam output circuit. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the headlight (right) high beam is stopped. ・Current and past failures are set. |
| C1728[96] |
DTC C1728[96] Right Head Light (High Beam) Output Circuit Component Internal Failure |
・The BCM commands the headlight (right) high beam ON. |
・The BCM receives an error signal of the LED headlight (right) high beam for 2 seconds or more. |
・The LED headlight warning light illuminates. ・For models with MID, RH Headlight failure is displayed. ・The output of the LED headlight (right) high beam is stopped. ・Current and past failures are set. |
| C1729[11] |
DTC C1729[11] Left Head Light (High Beam) Output Circuit Short to Ground |
・The BCM commands the headlight (left) high beam ON. |
Any of the following are met: ・The BCM detects a short to ground in the headlight (left) high beam output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the headlight (left) high beam output circuit for 2 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) high beam is stopped until the next command is given. ・Current and past failures are set. |
| C1729[12] |
DTC C1729[12] Left Head Light (High Beam) Output Circuit Short to Battery |
・The BCM commands the headlight (left) high beam OFF. |
・The BCM detects a short to the power supply in the headlight (left) high beam output circuit for 2.5 seconds or more. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) high beam is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C1729[13] |
DTC C1729[13] Left Head Light (High Beam) Output Circuit Open |
・The BCM commands the headlight (left) high beam OFF. |
・The BCM detects an open circuit in the headlight (left) high beam output circuit for 2 seconds or more. |
・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) high beam is stopped. ・Current and past failures are set. |
| C1729[49] |
DTC C1729[49] Left Head Light (High Beam) Output Circuit Internal Electronic Failure |
・The BCM commands the headlight (left) high beam ON. |
・The BCM detects an internal malfunction in the headlight (left) high beam output circuit. |
・For models with LED headlights, the LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the headlight (left) high beam is stopped. ・Current and past failures are set. |
| C1729[96] |
DTC C1729[96] Left Head Light (High Beam) Output Circuit Component Internal Failure |
・The BCM commands the headlight (left) high beam ON. |
・The BCM receives an error signal of the LED headlight (left) high beam for 2 seconds or more. |
・The LED headlight warning light illuminates. ・For models with MID, LH Headlight failure is displayed. ・The output of the LED headlight (left) high beam is stopped until the next command is given. ・Current and past failures are set. |
| C172C[11] |
DTC C172C[11] Right Tail Light Output Circuit Short to Ground |
・The BCM commands the clearance light (right) and taillight (right) ON. |
Any of the following is met: ・The BCM detects a short to ground in the clearance light (right) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the clearance light (right) output circuit for 2 seconds or more. ・The BCM detects a short to ground in the taillight (right) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the taillight (right) output circuit for 2 seconds or more. |
・For models with MID, RH taillight failure is displayed. The output of the clearance light (right) or taillight (right) is stopped until the next command is given. ・Current and past failures are set. |
| C172C[12] |
DTC C172C[12] Right Tail Light Output Circuit Short to Battery |
・The BCM commands the clearance light (right) and taillight (right) OFF. |
Any of the following is met: ・The BCM detects a short to the power supply in the clearance light (right) output circuit for 2.5 seconds or more. ・The BCM detects a short to the power supply in the taillight (right) output circuit for 2.5 seconds or more. |
・For models with MID, RH taillight failure is displayed. ・The output of the clearance light (right) or taillight (right) is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C172C[49] |
DTC C172C[49] Right Tail Light Output Circuit Internal Electronic Failure |
・The BCM commands the clearance light (right) and taillight (right) ON. |
Any of the following is met: ・The BCM detects an internal malfunction in the clearance light (right) output circuit. ・The BCM detects an internal malfunction in the taillight (right) output circuit. |
・For models with MID, RH taillight failure is displayed. ・The output of the clearance light (right) or taillight (right) is stopped. ・Current and past failures are set. |
| C172D[11] |
DTC C172D[11] Left Tail Light Output Circuit Short to Ground |
・The BCM commands the clearance light (left), taillight (left), and illumination light ON. |
Any of the following is met: ・The BCM detects a short to ground in the clearance light (left) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the clearance light (left) output circuit for 2 seconds or more. ・The BCM detects a short to ground in the taillight (left) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the taillight (left) output circuit for 2 seconds or more. ・The BCM detects a short to ground in the illumination light output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the illumination light output circuit for 2 seconds or more. |
・For models with MID, LH taillight failure is displayed. ・The output of the clearance light (left), taillight (left), or illumination light is stopped until the next command is given. ・Current and past failures are set. |
| C172D[12] |
DTC C172D[12] Left Tail Light Output Circuit Short to Battery |
・The BCM commands the clearance light (left), taillight (left), and illumination light OFF. |
Any of the following is met: ・The BCM detects a short to the power supply in the clearance light (left) output circuit for 2.5 seconds or more. ・The BCM detects a short to the power supply in the taillight (left) output circuit for 2.5 seconds or more. ・The BCM detects a short to the power supply in the illumination light output circuit for 2.5 seconds or more. |
・For models with MID, LH taillight failure is displayed. ・The output of the clearance light (left), taillight (left,) or illumination light is turned ON regardless of the input light control switch signal. ・Current and past failures are set. |
| C172D[49] |
DTC C172D[49] Left Tail Light Output Circuit Internal Electronic Failure |
・The BCM commands the clearance light (left), taillight (left), and illumination light ON. |
Any of the following is met: ・The BCM detects an internal malfunction in the clearance light (left) output circuit. ・The BCM detects an internal malfunction in the taillight (left) output circuit. ・The BCM detects an internal malfunction in the illumination light output circuit. |
・For models with MID, LH taillight failure is displayed. ・The output of the clearance light (left), taillight (left), or illumination light is stopped. ・Current and past failures are set. |
| C172E[12] |
DTC C172E[12] DRL Right Circuit Short to Battery |
・The DRL operation conditions are met. |
Any of the following is met: ・The BCM detects a short to the power supply in the DRL (right) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the DRL (right) output circuit for 2 seconds or more. |
・The DRL (right) does not operate normally. ・Current and past failures are set. |
| C172E[49] |
DTC C172E[49] DRL Right Circuit Internal Electronic Failure |
・The DRL operation conditions are met. |
・The BCM detects an internal malfunction in the DRL (right) output circuit. |
・The output of the DRL (right) is stopped. ・Current and past failures are set. |
| C172F[12] |
DTC C172F[12] DRL Left Circuit Short to Battery |
・The DRL operation conditions are met. |
Any of the following is met: ・The BCM detects a short to the power supply in the DRL (left) output circuit for 2.5 seconds or more. ・The BCM detects an overloading to the DRL (left) output circuit for 2 seconds or more. |
・The DRL (left) does not operate normally. ・Current and past failures are set. |
| C172F[49] |
DTC C172F[49] DRL Left Circuit Internal Electronic Failure |
・The DRL operation conditions are met. |
・The BCM detects an internal malfunction in the DRL (left) output circuit. |
・The output of the DRL (left) is stopped. ・Current and past failures are set. |
| P254F[11] |
DTC P254F[11] Engine Hood Switch Input Circuit Short to Ground |
- |
・The BCM detects a short to ground in the engine hood switch input circuit for 2 seconds or more. |
・The anti-theft system does not operate normally. ・Current and past failures are set. |
| P254F[15] |
DTC P254F[15] Engine Hood Switch Input Circuit Short to Battery or Open |
- |
・The BCM detects an open circuit or a short to the power supply in the engine hood switch input circuit for 2 seconds or more. |
・The anti-theft system does not operate normally. ・Current and past failures are set. |
| P254F[1C] |
DTC P254F[1C] Engine Hood Switch Input Circuit Voltage Out of Range |
- |
・The BCM detects an abnormal voltage in the engine hood switch input circuit for 2 seconds or more. |
・The anti-theft system does not operate normally. ・Current and past failures are set. |
| U0064[88] |
DTC U0064[88] CAN Communication Malfunction (CAN 1 Bus Off) |
- |
・The BCM detects a Bus OFF status in the CAN communication circuit. |
・Current and past failures are set. |
| U1800[86] |
DTC U1800[86] Lost Communication With ECM |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the ECM cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1801[86] |
DTC U1801[86] Lost Communication With TCM |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the TCM cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1821[86] |
DTC U1821[86] Lost Communication With EHCU |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the EHCU cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1851[86] |
DTC U1851[86] CAN Communication or Input Data Malfunction With SRS Control Unit |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the SRS control unit cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1855[86] |
DTC U1855[86] Lost Communication With Instrument Panel Cluster |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the instrument panel cluster cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1A01[86] |
DTC U1A01[86] Lost Communication With Front Camera |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the stereo camera cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1A0E[86] |
DTC U1A0E[86] Lost Communication With Wireless Access Module |
- |
・The BCM detects that the control information sent from the wireless access module cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1A10[86] |
DTC U1A10[86] Lost Communication With Radar Sensor Left |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the radar sensor (left) cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U1A11[86] |
DTC U1A11[86] Lost Communication With Radar Sensor Right |
・The ignition switch is ON. |
・The BCM detects that the control information sent from the radar sensor (right) cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U2011[86] |
DTC U2011[86] Lost Communication With Rain and Light Sensor |
- |
・The BCM detects that the control information sent from the rain and light sensor cannot be received for 3 seconds or more. |
・Current and past failures are set. |
| U2012[86] |
DTC U2012[86] Lost Communication With Smart Wiper |
- |
・The BCM detects that the control information sent from the wiper motor cannot be received for 3 seconds or more. |
・Current and past failures are set. |