PID/DATA MONITOR TABLE [BLIND SPOT MONITORING (BSM)]
id0902i3960700
BSM Control Module (LH)
|
PID name |
Unit/Status |
Data contents |
Inspection item(s) |
|---|---|---|---|
|
BSM_ST
|
On/Off
|
• On: BSM is operated.
• Off: BSM is not operated.
|
BSM control module (LH)
|
|
DTC_CNT
|
—
|
Number of DTCs stored in the BSM control module (LH) is displayed.
|
BSM control module (LH)
|
|
SHIFT_R
|
Not_R/R
|
ATX:
• Not_R: Selector lever is in position other than R.
• R: Selector lever is in R position.
MTX:
• Not_R: Shift lever is in position other than reverse.
• R: Shift lever is in reverse position.
|
ATX:
• Transaxle range sensor (TCM)
MTX:
• Back-up light switch
|
|
SWA_POS
|
° (deg)
|
Displays steering angle signal (estimated absolute angle)
• Steering wheel in neutral position: Near 0 degrees
• Steering wheel turned to left: Changes from 0 degrees to positive
• Steering wheel turned to right: Changes from 0 degrees to negative
|
• Perform the DTC inspection for the PCM, DSC HU/CM, and EPS CM, and if any DTC is displayed, repair the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [SKYACTIV-D 2.2].)
• After performing the DTC inspection, perform the following procedures:
• If an abnormal value is indicated again, replace the EPS CM.
|
|
TURN_SW_L
|
On/Off
|
• On: Turn switch is in LH position.
• Off: Turn switch is in position other than LH.
|
Turn Switch
|
|
TURN_SW_R
|
On/Off
|
• On: Turn switch is in RH position.
• Off: Turn switch is in position other than RH.
|
Turn Switch
|
|
VPWR_IG1
|
V
|
BSM control module (LH) power supply voltage is displayed.
|
• BSM control module (LH)
• IG1 relay
• Battery
|
|
VSPD
|
KPH, MPH
|
Vehicle speed is displayed.
|
—
|
|
WRN_IND_L
|
Off/On
|
• Off: BSM indicator light (LH) is not illuminated.
• On: BSM indicator light (LH) is illuminated.
|
BSM indicator light (LH)
|
BSM Control Module (RH)
|
PID name |
Unit/Status |
Data contents |
Inspection item(s) |
|---|---|---|---|
|
BSM_OFF_IL
|
On/Off
|
• On: BSM OFF indicator light is illuminated.
• Off: BSM OFF indicator light is not illuminated.
|
• BSM OFF switch
• Instrument cluster
|
|
BSM_ST
|
On/Off
|
• On: BSM is operated.
• Off: BSM is not operated.
|
BSM control module (RH)
|
|
Buzzer
|
On/Off
|
• On: BSM buzzer is operated.
• Off: BSM buzzer is not operated.
|
• BSM control module
• Instrument cluster
|
|
DTC_CNT
|
—
|
Number of DTCs stored in the BSM control module (RH) is displayed.
|
BSM control module (RH)
|
|
SHIFT_R
|
Not_R/R
|
ATX:
• Not_R: Selector lever is in position other than R.
• R: Selector lever is in R position.
MTX:
• Not_R: Shift lever is in position other than reverse.
• R: Shift lever is in reverse position.
|
ATX:
• Transaxle range sensor (TCM)
MTX:
• Back-up light switch
|
|
SWA_POS
|
° (deg)
|
Displays steering angle signal (estimated absolute angle)
• Steering wheel in neutral position: Near 0 degrees
• Steering wheel turned to left: Changes from 0 degrees to positive
• Steering wheel turned to right: Changes from 0 degrees to negative
|
• Perform the DTC inspection for the PCM, DSC HU/CM, and EPS CM, and if any DTC is displayed, repair the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [SKYACTIV-D 2.2].)
• After performing the DTC inspection, perform the following procedures:
• If an abnormal value is indicated again, replace the EPS CM.
|
|
TURN_SW_L
|
On/Off
|
• On: Turn switch is in LH position.
• Off: Turn switch is in position other than LH.
|
Turn Switch
|
|
TURN_SW_R
|
On/Off
|
• On: Turn switch is in RH position.
• Off: Turn switch is in position other than RH.
|
Turn Switch
|
|
VPWR_IG1
|
V
|
BSM control module (RH) power supply voltage is displayed.
|
• BSM control module (RH)
• IG1 relay
• Battery
|
|
VSPD
|
KPH, MPH
|
Vehicle speed is displayed.
|
—
|
|
WRN_IND_R
|
Off/On
|
• Off: BSM indicator light (RH) is not illuminated.
• On: BSM indicator light (RH) is illuminated.
|
BSM indicator light (RH)
|