DETERMINING SHORT BETWEEN CIRCUITS LOCATION (MS-CAN) [SKYACTIV-D 2.2 (L.H.D.)]

• When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.

• When inspecting the DLC-2, touch it with a paper clip or similar thin pin without directly inserting a tester into the terminals.

Step	Inspection	Action
1	INSPECT BETWEEN INSTRUMENT CLUSTER AND REAR BODY CONTROL MODULE (RBCM) FOR SHORT BETWEEN CIRCUITS • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Disconnect the rear body control module (RBCM) connector. • Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Switch the ignition ON (engine off). • Measure the voltage at DLC-2 terminals L and K. • Is the voltage at DLC-2 terminals L and K the same?	Yes	Go to the next step.
No	Go to Step 12.
2	INSPECT BETWEEN CONNECTOR C-08 AND INSTRUMENT CLUSTER FOR SHORT BETWEEN CIRCUITS • Switch the ignition off (LOCK). • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Disconnect connector C-08. • Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Switch the ignition ON (engine off). • Measure the voltage at DLC-2 terminals L and K. • Is the voltage at DLC-2 terminals L and K the same?	Yes	Go to the next step.
No	Repair or replace the wiring harness between the connector C-34 and connector C-08 because the wiring harness is shorted between circuits.
3	INSPECT BETWEEN CONNECTOR C-34 AND DLC-2 FOR SHORT BETWEEN CIRCUITS • Switch the ignition off (LOCK). • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Disconnect connector C-34. • Inspect for continuity between DLC-2 terminals L and K. • Is there continuity?	Yes	Repair or replace the wiring harness between connector C-34 and DLC-2 because the wiring harness is shorted between circuits.
No	Go to the next step.
4	INSPECT BETWEEN CONNECTOR C-34 AND CLIMATE CONTROL UNIT FOR SHORT BETWEEN CIRCUITS • Inspect for continuity between climate control unit terminals 1O and 1Q. (with full-auto air conditioner) • Inspect for continuity between climate control unit terminals D and B. (with manual air conditioner) • Is there continuity?	Yes	Go to the next step.
No	• Go to Step 8. (with full-auto air conditioner) • Go to Step 6. (with manual air conditioner)
5	INSPECT CLIMATE CONTROL UNIT FOR SHORT BETWEEN CIRCUITS • Disconnect the climate control unit connector. • Inspect for continuity between climate control unit terminals 1O and 1Q (wiring harness side). (with full-auto air conditioner) • Inspect for continuity between climate control unit terminals D and B (wiring harness side). (with manual air conditioner) • Is there continuity?	Yes	Repair or replace the wiring harness between the climate control unit and connector C-34 because the wiring harness is shorted between circuits.
No	Replace the climate control unit because there is a short between circuits inside the climate control unit. (See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER].) (See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER].)
6	INSPECT BETWEEN CONNECTOR C-34 AND INDICATOR UNIT FOR SHORT BETWEEN CIRCUITS • Inspect for continuity between indicator unit terminals E and G. • Is there continuity?	Yes	Go to the next step.
No	Go to Step 8.
7	INSPECT INDICATOR UNIT FOR SHORT BETWEEN CIRCUITS • Disconnect the indicator unit connector. • Inspect for continuity between indicator unit terminals E and G (wiring harness side). • Is there continuity?	Yes	Repair or replace the wiring harness between the indicator unit and connector C-34 because the wiring harness is shorted between circuits.
No	Replace the indicator unit because there is a short between circuits inside the indicator unit. (See INDICATOR UNIT REMOVAL/INSTALLATION.)
8	INSPECT BETWEEN CONNECTOR C-34 AND PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT BETWEEN CIRCUITS • Inspect for continuity between parking assist unit (ultrasonic) terminals AA and AB. • Is there continuity?	Yes	Go to the next step.
No	Go to Step 10.
9	INSPECT PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT BETWEEN CIRCUITS • Disconnect the parking assist unit (ultrasonic) connector. • Inspect for continuity between parking assist unit (ultrasonic) terminals AA and AB (wiring harness side). • Is there continuity?	Yes	Repair or replace the wiring harness between the parking assist unit (ultrasonic) and connector C-34 because the wiring harness is shorted between circuits.
No	Replace the parking assist unit (ultrasonic) because there is a short between circuits inside the parking assist unit (ultrasonic). (See PARKING ASSIST UNIT (ULTRASONIC) REMOVAL/INSTALLATION.)
10	INSPECT BETWEEN CONNECTOR C-34 AND INSTRUMENT CLUSTER FOR SHORT BETWEEN CIRCUITS • Disconnect the instrument cluster connector. • Inspect for continuity between instrument cluster terminals C and E (wiring harness side). • Is there continuity?	Yes	Repair or replace the wiring harness between connector C-34 and instrument cluster because the wiring harness is shorted between circuits.
No	Go to the next step.
11	INSPECT INSTRUMENT CLUSTER FOR SHORT BETWEEN CIRCUITS • Connect connector C-34. • Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Switch the ignition ON (engine off). • Measure the voltage at DLC-2 terminals L and K. • Is the voltage at DLC-2 terminals L and K the same?	Yes	Repair or replace the wiring harness between connector C-34 and connector C-08 because the wiring harness is shorted between circuits.
No	Replace the instrument cluster because there is a short between circuits in the instrument cluster. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
12	INSPECT BETWEEN BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) AND REAR BODY CONTROL MODULE (RBCM) FOR SHORT BETWEEN CIRCUITS • Switch the ignition off (LOCK). • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Inspect for continuity between blind spot monitoring (BSM) control module (LH) terminals D and E. • Is there continuity?	Yes	Go to the next step.
No	Go to Step 15.
13	INSPECT BETWEEN REAR BODY CONTROL MODULE (RBCM) AND CONNECTOR C-23 FOR SHORT BETWEEN CIRCUITS • Disconnect connector C-23. • Inspect the continuity between blind spot monitoring (BSM) control module (LH) terminals D and E. • Is there continuity?	Yes	Go to the next step.
No	Repair or replace the wiring harness between the rear body control module (RBCM) and connector C-23 because the wiring harness is shorted between circuits.
14	INSPECT BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) FOR SHORT BETWEEN CIRCUITS • Disconnect the blind spot monitoring (BSM) control module (LH) connector. • Inspect for continuity between blind spot monitoring (BSM) control module (LH) terminals D and E (wiring harness side). • Is there continuity?	Yes	Repair or replace the wiring harness between the blind spot monitoring (BSM) control module (LH) and connector C-23 because the wiring harness is shorted between circuits.
No	Replace the blind spot monitoring (BSM) control module (LH) because there is a short between circuits in the blind spot monitoring (BSM) control module (LH). (See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION [Except Australian specs.].)
15	INSPECT BETWEEN REAR MOUNT CAMERA AND REAR BODY CONTROL MODULE (RBCM) FOR SHORT BETWEEN CIRCUITS • Inspect for continuity between rear mount camera terminals G and H. • Is there continuity?	Yes	Go to the next step.
No	Replace the rear body control module (RBCM) because there is a short between circuits in the rear body control module (RBCM). (See REAR BODY CONTROL MODULE (RBCM) REMOVAL/INSTALLATION.)
16	INSPECT BETWEEN REAR BODY CONTROL MODULE (RBCM) AND CONNECTOR C-21 FOR SHORT BETWEEN CIRCUITS • Disconnect connector C-21. • Inspect the continuity between rear mount camera terminals G and H. • Is there continuity?	Yes	Go to the next step.
No	Repair or replace the wiring harness between the rear body control module (RBCM) and connector C-21 because the wiring harness is shorted between circuits.
17	INSPECT REAR MOUNT CAMERA FOR SHORT BETWEEN CIRCUITS • Disconnect the rear mount camera connector. • Inspect for continuity between rear mount camera terminals G and H (wiring harness side). • Is there continuity?	Yes	Repair or replace the wiring harness between the rear mount camera and connector C-21 because the wiring harness is shorted between circuits.
No	Replace the rear mount camera because there is a short between circuits in the rear mount camera. (See REAR MOUNT CAMERA REMOVAL/INSTALLATION.)

Step

Inspection

Action

INSPECT BETWEEN INSTRUMENT CLUSTER AND REAR BODY CONTROL MODULE (RBCM) FOR SHORT BETWEEN CIRCUITS

• Disconnect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Disconnect the rear body control module (RBCM) connector.

• Connect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Switch the ignition ON (engine off).

• Measure the voltage at DLC-2 terminals L and K.

• Is the voltage at DLC-2 terminals L and K the same?

Yes

Go to the next step.

Go to Step 12.

INSPECT BETWEEN CONNECTOR C-08 AND INSTRUMENT CLUSTER FOR SHORT BETWEEN CIRCUITS

• Switch the ignition off (LOCK).

• Disconnect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Disconnect connector C-08.

• Connect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Switch the ignition ON (engine off).

• Measure the voltage at DLC-2 terminals L and K.

• Is the voltage at DLC-2 terminals L and K the same?

Yes

Go to the next step.

Repair or replace the wiring harness between the connector C-34 and connector C-08 because the wiring harness is shorted between circuits.

INSPECT BETWEEN CONNECTOR C-34 AND DLC-2 FOR SHORT BETWEEN CIRCUITS

• Switch the ignition off (LOCK).

• Disconnect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Disconnect connector C-34.

• Inspect for continuity between DLC-2 terminals L and K.

• Is there continuity?

Yes

Repair or replace the wiring harness between connector C-34 and DLC-2 because the wiring harness is shorted between circuits.

Go to the next step.

INSPECT BETWEEN CONNECTOR C-34 AND CLIMATE CONTROL UNIT FOR SHORT BETWEEN CIRCUITS

• Inspect for continuity between climate control unit terminals 1O and 1Q. (with full-auto air conditioner)

• Inspect for continuity between climate control unit terminals D and B. (with manual air conditioner)

• Is there continuity?

Yes

Go to the next step.

• Go to Step 8. (with full-auto air conditioner)

• Go to Step 6. (with manual air conditioner)

INSPECT CLIMATE CONTROL UNIT FOR SHORT BETWEEN CIRCUITS

• Disconnect the climate control unit connector.

• Inspect for continuity between climate control unit terminals 1O and 1Q (wiring harness side). (with full-auto air conditioner)

• Inspect for continuity between climate control unit terminals D and B (wiring harness side). (with manual air conditioner)

• Is there continuity?

Yes

Repair or replace the wiring harness between the climate control unit and connector C-34 because the wiring harness is shorted between circuits.

Replace the climate control unit because there is a short between circuits inside the climate control unit.

(See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER].)

(See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER].)

INSPECT BETWEEN CONNECTOR C-34 AND INDICATOR UNIT FOR SHORT BETWEEN CIRCUITS

• Inspect for continuity between indicator unit terminals E and G.

• Is there continuity?

Yes

Go to the next step.

Go to Step 8.

INSPECT INDICATOR UNIT FOR SHORT BETWEEN CIRCUITS

• Disconnect the indicator unit connector.

• Inspect for continuity between indicator unit terminals E and G (wiring harness side).

• Is there continuity?

Yes

Repair or replace the wiring harness between the indicator unit and connector C-34 because the wiring harness is shorted between circuits.

Replace the indicator unit because there is a short between circuits inside the indicator unit.

(See INDICATOR UNIT REMOVAL/INSTALLATION.)

INSPECT BETWEEN CONNECTOR C-34 AND PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT BETWEEN CIRCUITS

• Inspect for continuity between parking assist unit (ultrasonic) terminals AA and AB.

• Is there continuity?

Yes

Go to the next step.

Go to Step 10.

INSPECT PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT BETWEEN CIRCUITS

• Disconnect the parking assist unit (ultrasonic) connector.

• Inspect for continuity between parking assist unit (ultrasonic) terminals AA and AB (wiring harness side).

• Is there continuity?

Yes

Repair or replace the wiring harness between the parking assist unit (ultrasonic) and connector C-34 because the wiring harness is shorted between circuits.

Replace the parking assist unit (ultrasonic) because there is a short between circuits inside the parking assist unit (ultrasonic).

(See PARKING ASSIST UNIT (ULTRASONIC) REMOVAL/INSTALLATION.)

INSPECT BETWEEN CONNECTOR C-34 AND INSTRUMENT CLUSTER FOR SHORT BETWEEN CIRCUITS

• Disconnect the instrument cluster connector.

• Inspect for continuity between instrument cluster terminals C and E (wiring harness side).

• Is there continuity?

Yes

Repair or replace the wiring harness between connector C-34 and instrument cluster because the wiring harness is shorted between circuits.

Go to the next step.

INSPECT INSTRUMENT CLUSTER FOR SHORT BETWEEN CIRCUITS

• Connect connector C-34.

• Connect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Switch the ignition ON (engine off).

• Measure the voltage at DLC-2 terminals L and K.

• Is the voltage at DLC-2 terminals L and K the same?

Yes

Repair or replace the wiring harness between connector C-34 and connector C-08 because the wiring harness is shorted between circuits.

Replace the instrument cluster because there is a short between circuits in the instrument cluster.

(See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)

INSPECT BETWEEN BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) AND REAR BODY CONTROL MODULE (RBCM) FOR SHORT BETWEEN CIRCUITS

• Switch the ignition off (LOCK).

• Disconnect the negative battery cable.

(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

• Inspect for continuity between blind spot monitoring (BSM) control module (LH) terminals D and E.

• Is there continuity?

Yes

Go to the next step.

Go to Step 15.

INSPECT BETWEEN REAR BODY CONTROL MODULE (RBCM) AND CONNECTOR C-23 FOR SHORT BETWEEN CIRCUITS

• Disconnect connector C-23.

• Inspect the continuity between blind spot monitoring (BSM) control module (LH) terminals D and E.

• Is there continuity?

Yes

Go to the next step.

Repair or replace the wiring harness between the rear body control module (RBCM) and connector C-23 because the wiring harness is shorted between circuits.

INSPECT BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) FOR SHORT BETWEEN CIRCUITS

• Disconnect the blind spot monitoring (BSM) control module (LH) connector.

• Inspect for continuity between blind spot monitoring (BSM) control module (LH) terminals D and E (wiring harness side).

• Is there continuity?

Yes

Repair or replace the wiring harness between the blind spot monitoring (BSM) control module (LH) and connector C-23 because the wiring harness is shorted between circuits.

Replace the blind spot monitoring (BSM) control module (LH) because there is a short between circuits in the blind spot monitoring (BSM) control module (LH).

(See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION [Except Australian specs.].)

INSPECT BETWEEN REAR MOUNT CAMERA AND REAR BODY CONTROL MODULE (RBCM) FOR SHORT BETWEEN CIRCUITS

• Inspect for continuity between rear mount camera terminals G and H.

• Is there continuity?

Yes

Go to the next step.

Replace the rear body control module (RBCM) because there is a short between circuits in the rear body control module (RBCM).

(See REAR BODY CONTROL MODULE (RBCM) REMOVAL/INSTALLATION.)

INSPECT BETWEEN REAR BODY CONTROL MODULE (RBCM) AND CONNECTOR C-21 FOR SHORT BETWEEN CIRCUITS

• Disconnect connector C-21.

• Inspect the continuity between rear mount camera terminals G and H.

• Is there continuity?

Yes

Go to the next step.

Repair or replace the wiring harness between the rear body control module (RBCM) and connector C-21 because the wiring harness is shorted between circuits.

INSPECT REAR MOUNT CAMERA FOR SHORT BETWEEN CIRCUITS

• Disconnect the rear mount camera connector.

• Inspect for continuity between rear mount camera terminals G and H (wiring harness side).

• Is there continuity?

Yes

Repair or replace the wiring harness between the rear mount camera and connector C-21 because the wiring harness is shorted between circuits.

Replace the rear mount camera because there is a short between circuits in the rear mount camera.

(See REAR MOUNT CAMERA REMOVAL/INSTALLATION.)