DTC P0615:00 [PCM (SKYACTIV-D 2.2)]

id0102j5061500

DTC P0615:00

Starter relay circuit problem

DETECTION CONDITION

•  When the number of times the engine has been started has reached the warrantied performance frequency for the starter or starter relay.

Diagnostic support note

•  This is a continuous monitor (other).

•  The check engine light does not illuminate.

•  FREEZE FRAME DATA/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Not applicable

POSSIBLE CAUSE

•  When the number of times the engine has been started has reached the warrantied performance frequency of 180,000 times for the starter or starter relay.

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0615:00	Starter relay circuit problem
DETECTION CONDITION	• When the number of times the engine has been started has reached the warrantied performance frequency for the starter or starter relay. Diagnostic support note • This is a continuous monitor (other). • The check engine light does not illuminate. • FREEZE FRAME DATA/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Not applicable
POSSIBLE CAUSE	• When the number of times the engine has been started has reached the warrantied performance frequency of 180,000 times for the starter or starter relay. • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

Note

•  Recording can be facilitated using the screen capture function of the PC.

•  Record the freeze frame data/snap shot data.

—

Go to the next step.

2

REPLACE STARTER AND STARTER RELAY

•  Switch the ignition OFF.

•  Replace the starter and starter relay.
(See STARTER REMOVAL/INSTALLATION [SKYACTIV-D 2.2])

(See RELAY LOCATION

—

Go to the next step.

3

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.
(See CLEARING DTC [PCM (SKYACTIV-D 2.2)])

•  Start the engine and warm it up.

•  Display the DTCs using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)])

•  Has DTC P0615:00 been recorded?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2])

No

Go to the next step.

4

VERIFY OTHER DTCs

•  Has any other DTC or pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-D 2.2)])

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the freeze frame data/snap shot data.	—	Go to the next step.
2	REPLACE STARTER AND STARTER RELAY • Switch the ignition OFF. • Replace the starter and starter relay. (See STARTER REMOVAL/INSTALLATION [SKYACTIV-D 2.2]) (See RELAY LOCATION	—	Go to the next step.
3	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. (See CLEARING DTC [PCM (SKYACTIV-D 2.2)]) • Start the engine and warm it up. • Display the DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)]) • Has DTC P0615:00 been recorded?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2])
3		No	Go to the next step.
4	VERIFY OTHER DTCs • Has any other DTC or pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D 2.2)])
4		No	DTC troubleshooting completed.