FRONT DRIVE SHAFT REMOVAL/INSTALLATION

id031300800300

Caution

•  Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate place where the sensor will not be pulled by mistake while the vehicle is being serviced.

1.  Remove the side cover.

2.  When working on the left side of the vehicle, disconnect the front auto leveling sensor link lower side. (Vehicle with headlight auto leveling system) (See FRONT AUTO LEVELING SENSOR REMOVAL/INSTALLATION.)

3.  Remove the front ABS wheel-speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION.)

4.  Remove in the order indicated in the table.

5.  Install in the reverse order of removal.

ac9wzw00006524

1	Locknut (crimped-fix type)/Locknut (self-lock type) (See Locknut (Crimped-fix Type) Removal Note.) (See Locknut (Crimped-fix Type) Installation Note.)
2	Tie-rod end ball joint (See FRONT CROSSMEMBER REMOVAL/INSTALLATION [L.H.D.].) (See FRONT CROSSMEMBER REMOVAL/INSTALLATION [R.H.D.].)
3	Front stabilizer control link (lower side)
4	Front lower arm ball joint
5	Front drive shaft (See Front Drive Shaft Removal Note.) (See Front Drive Shaft Installation Note.)
6	Front drive shaft clip (See Front Drive Shaft Clip Installation Note.)
7	Joint shaft clip (See JOINT SHAFT REMOVAL/INSTALLATION [2WD].) (See JOINT SHAFT REMOVAL/INSTALLATION [4WD].)

Locknut (Crimped-fix Type) Removal Note

Note

•  The locknuts include two types; a self-lock type and a crimped-fix type. Verify which type of locknut is used on the vehicle being serviced. If it is a crimped-fix type locknut, remove it using the following procedure.

1.  Knock the crimped portion of the locknut outward using a small chisel and a hammer.

ac9uuw00001641

2.  Lock the hub by applying the brakes.

3.  Remove the locknut.

Front Drive Shaft Removal Note

1.  Install a spare nut onto the drive shaft so that the nut is flush with the end of the drive shaft.

2.  Tap the nut with a copper hammer to loosen the drive shaft from the front wheel hub.

ac9uuw00001642

3.  Separate the drive shaft from the wheel hub.

Caution

•  The sharp edges of the drive shaft can slice or puncture the oil seal. Be careful when removing the drive shaft from the transaxle.

4.  Separate the left side drive shaft from the transaxle by prying with a bar inserted between the outer ring and the transaxle, as shown in the figure.

ac9uuw00001643

5.  Separate the right side drive shaft from the joint shaft by using the SSTs.

ac9uuw00002439

Front Drive Shaft Clip Installation Note

1.  Install a new clip onto the drive shaft with the opening facing upward. Ensure that the diameter of the clip does not exceed the specification on installation.

2.  After installation, measure the outer diameter. If it exceeds the specification, repeat Steps 1—2 using a new clip.

ac9uuw00001644

Front Drive Shaft Installation Note

Caution

•  The sharp edges of the drive shaft can slice or puncture the oil seal. Be careful when installing the drive shaft to the transaxle.

•  The oil seals are damaged easily if this procedure is not done correctly.

ac9uuw00001645

Left side

1.  Apply grease (D4Y0 33247) to the wheel bearing inner race and drive shaft contact surface (Area A in figure).

acxuuw00003013

2.  Insert the drive shaft into the wheel hub.

3.  Apply transaxle oil to the oil seal lip.

4.  Push the drive shaft into the transaxle.

5.  After installation, pull the transaxle side outer ring forward to confirm that the drive shaft is securely held by the clip.

Right side

1.  Apply grease (D4Y0 33247) to the wheel bearing inner race and drive shaft contact surface (Area A in figure).

acxuuw00003015

2.  Insert the drive shaft into the wheel hub.

3.  Insert the drive shaft into the joint shaft.

4.  After installation, pull the transaxle side outer ring forward to confirm that the drive shaft is securely held by the clip.

Locknut (Crimped-fix Type) Installation Note

1.  Install a new locknut and stake it as shown.

ac9wzw00000814