DTC P060B [MZI-3.7]

id0102d2881300

DTC P060B

Internal control module A/D processing performance

DETECTION CONDITION

• Indicates that an error occurred in the PCM.

POSSIBLE CAUSE

• PCM malfunction

DTC P060B	Internal control module A/D processing performance
DETECTION CONDITION	• Indicates that an error occurred in the PCM.
POSSIBLE CAUSE	• PCM malfunction

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA HAS BEEN RECORDED

•  Has FREEZE FRAME DATA been recorded?

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the repair order, then go to the next step.

2

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

•  Verify related Service Information availability.

•  Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

•  If the vehicle is not repaired, go to the next step.

No

Go to the next step.

3

VERIFY RELATED PENDING CODE OR STORED DTCs

•  Turn the ignition switch off then to the ON position (Engine off).

•  Verify related pending code or stored DTCs.

•  Are other DTCs present?

Yes

Go to the appropriate DTC troubleshooting.

(See DTC TABLE [MZI-3.7].)

No

Go to the next step.

4

INSPECT FOR REFERENCE VOLTAGE CONCERNS

•  Inspect the PCM wiring harness for damage.

•  Verify the correct operation of the sensors using ETCREF, VREF and related circuits.

•  Is a concern present?

Yes

Go to the next step.

No

Go to Step 6.

5

INSPECT FOR CORRECT PCM OPERATION

•  Disconnect all the PCM connectors.

•  Visually inspect for:

―   Pushed out pins

―   Corrosion

•  Connect all the PCM connectors and verify that they seat correctly.

•  Retrieve DTCs using the M-MDS.

•  Is the PENDING CODE for this DTC present?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [MZI-3.7].)

No

Go to the next step.

6

VERIFY TROUBLESHOOTING OF DTC P060B HAS BEEN COMPLETED

•  Verify that all disconnected connectors reconnected.

•  Turn the ignition switch to the ON position (Engine off).

•  Clear the DTC from the PCM memory using the M-MDS.

•  Perform the “KOEO and KOER self-test”.
(See KOEO/KOER SELF TEST [MZI-3.7].)

•  Retrieve DTCs using the M-MDS.

•  Is the PENDING CODE for this DTC present?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [MZI-3.7].)

No

Go to the next step.

7

VERIFY AFTER REPAIR PROCEDURE

•  Perform the “AFTER REPAIR PROCEDURE”.
(See AFTER REPAIR PROCEDURE [MZI-3.7].)

•  Are any DTC present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [MZI-3.7].)

No

Troubleshooting completed.

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED • Has FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record FREEZE FRAME DATA on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY RELATED PENDING CODE OR STORED DTCs • Turn the ignition switch off then to the ON position (Engine off). • Verify related pending code or stored DTCs. • Are other DTCs present?	Yes	Go to the appropriate DTC troubleshooting. (See DTC TABLE [MZI-3.7].)
3		No	Go to the next step.
4	INSPECT FOR REFERENCE VOLTAGE CONCERNS • Inspect the PCM wiring harness for damage. • Verify the correct operation of the sensors using ETCREF, VREF and related circuits. • Is a concern present?	Yes	Go to the next step.
4		No	Go to Step 6.
5	INSPECT FOR CORRECT PCM OPERATION • Disconnect all the PCM connectors. • Visually inspect for: ― Pushed out pins ― Corrosion • Connect all the PCM connectors and verify that they seat correctly. • Retrieve DTCs using the M-MDS. • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [MZI-3.7].)
5		No	Go to the next step.
6	VERIFY TROUBLESHOOTING OF DTC P060B HAS BEEN COMPLETED • Verify that all disconnected connectors reconnected. • Turn the ignition switch to the ON position (Engine off). • Clear the DTC from the PCM memory using the M-MDS. • Perform the “KOEO and KOER self-test”. (See KOEO/KOER SELF TEST [MZI-3.7].) • Retrieve DTCs using the M-MDS. • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [MZI-3.7].)
6		No	Go to the next step.
7	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [MZI-3.7].) • Are any DTC present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZI-3.7].)
7		No	Troubleshooting completed.