DTC P0D6F:00 [PCM (e-SKYACTIV)]

System malfunction location	Electric compressor (current sensor) : High input
Detection condition	• The PCM receives a condition signal from the electric compressor that the electric current value of the high voltage circuit of the electric compressor is above the specified value.
Fail-safe	• Refer to "DTC Table" and "Fail-safe Function Malfunction Contents Table". (See DTC TABLE [PCM (e-SKYACTIV)].)
Possible cause	• Electric compressor malfunction
System wiring diagram	• Not applicable
Connector diagram	• Not applicable

System malfunction location

Electric compressor (current sensor) : High input

Detection condition

• The PCM receives a condition signal from the electric compressor that the electric current value of the high voltage circuit of the electric compressor is above the specified value.

Fail-safe

• Refer to "DTC Table" and "Fail-safe Function Malfunction Contents Table". (See DTC TABLE [PCM (e-SKYACTIV)].)

Possible cause

• Electric compressor malfunction

System wiring diagram

• Not applicable

Connector diagram

• Not applicable

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION • Record the snapshot data. Note • Recording can be facilitated using the screen capture function of the PC.	—	Go to the next step.
2	VERIFY WHETHER MALFUNCTION IS PRESENT OR PAST • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Is DTC P0D6F:00 a present malfunction?	Yes	Go to the next step.
No	Go to the repair completion verification 1.
3	VERIFY WHETHER MALFUNCTION IS PRESENT OR PAST • Switch the main power OFF and wait for 30 s or more. • Switch the main power ON (READY on) and wait for 10 s or more. • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Is DTC P0D6F:00 a present malfunction?	Yes	Replace the electric compressor and perform the repair completion verification 1. (See ELECTRIC COMPRESSOR REMOVAL/INSTALLATION.)
No	Go to the repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED Warning <<High voltage>> • Wear insulated gloves when working on a high voltage system. • Install/connect the part removed/disconnected during the troubleshooting procedure. • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Warning • While performing this step, always operate the vehicle in a safe and lawful manner. • When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later. ― Drive the vehicle under the snapshot data condition. • Perform the DTC inspection for the PCM. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].) (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].) If the CAN communication is normal, perform the diagnosis from Step 1.
No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
No	DTC troubleshooting completed.

Step

Inspection

Results

Action

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

• Record the snapshot data.

Note

• Recording can be facilitated using the screen capture function of the PC.

—

Go to the next step.

VERIFY WHETHER MALFUNCTION IS PRESENT OR PAST

• Perform the DTC inspection for the PCM.

(See DTC INSPECTION.)

• Is DTC P0D6F:00 a present malfunction?

Yes

Go to the next step.

Go to the repair completion verification 1.

VERIFY WHETHER MALFUNCTION IS PRESENT OR PAST

• Switch the main power OFF and wait for 30 s or more.

• Switch the main power ON (READY on) and wait for 10 s or more.

• Perform the DTC inspection for the PCM.

(See DTC INSPECTION.)

• Is DTC P0D6F:00 a present malfunction?

Yes

Replace the electric compressor and perform the repair completion verification 1.

(See ELECTRIC COMPRESSOR REMOVAL/INSTALLATION.)

Go to the repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

Warning

<<High voltage>>

• Wear insulated gloves when working on a high voltage system.

• Install/connect the part removed/disconnected during the troubleshooting procedure.

• Clear the DTC recorded in the memory.

(See CLEARING DTC.)

• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.

Warning

• While performing this step, always operate the vehicle in a safe and lawful manner.

• When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.

― Drive the vehicle under the snapshot data condition.

• Perform the DTC inspection for the PCM.

(See DTC INSPECTION.)

• Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].)

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].)

If the CAN communication is normal, perform the diagnosis from Step 1.

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTCs DISPLAYED

• Perform the DTC inspection.

(See DTC INSPECTION.)

• Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

DTC troubleshooting completed.