DTC U0316:09 [RADAR UNIT]

id1502a6018900

System malfunction location

Error signal received from DSC HU/CM

Detection condition

•  There is an error in the following signals sent from the DSC HU/CM.

―  Yaw rate signal

―  Lateral-G signal

―  Longitudinal-G signal

―  Wheel speed signal

―  Brake fluid pressure signal

―  Cruise control system control signal

―  Signal error in brake light circuit

Fail-safe

•  Inhibits the Mazda radar cruise control (MRCC) system control

•  Inhibits the smart brake support (SBS) system control

•  Inhibits the distance recognition support system (DRSS) control

Possible cause

•  DSC HU/CM malfunction

•  SAS control module malfunction

•  BCM malfunction

•  Radar unit malfunction

System wiring diagram

•  Not applicable

System malfunction location	Error signal received from DSC HU/CM
Detection condition	• There is an error in the following signals sent from the DSC HU/CM. ― Yaw rate signal ― Lateral-G signal ― Longitudinal-G signal ― Wheel speed signal ― Brake fluid pressure signal ― Cruise control system control signal ― Signal error in brake light circuit
Fail-safe	• Inhibits the Mazda radar cruise control (MRCC) system control • Inhibits the smart brake support (SBS) system control • Inhibits the distance recognition support system (DRSS) control
Possible cause	• DSC HU/CM malfunction • SAS control module malfunction • BCM malfunction • Radar unit malfunction
System wiring diagram	• Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

PERFORM DTC INSPECTION FOR DSC HU/CM

•  Perform the DSC HU/CM DTC inspection using the M-MDS.
(See DTC INSPECTION [DSC HU/CM].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [DSC HU/CM].)

Then go to Step 5.

No

Go to the next step.

2

PERFORM DTC INSPECTION FOR SAS CONTROL MODULE

•  Perform the SAS control module DTC inspection using the M-MDS.
(See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

(See DTC INSPECTION [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

(See DTC TABLE [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].)

Then go to Step 5.

No

Go to the next step.

3

PERFORM DTC INSPECTION FOR BCM

•  Perform the BCM DTC inspection using the M-MDS.
(See DTC INSPECTION [BCM].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [BCM].)

Then go to Step 5.

No

Go to the next step.

4

PERFORM DTC INSPECTION FOR RADAR UNIT

•  Clear radar unit DTCs using the M-MDS.
(See CLEARING DTC [RADAR UNIT].)

•  Switch the ignition ON (engine on).

•  Drive the vehicle at 40 km/h (25 mph) or more for 3 min or more.

•  Perform the radar unit DTC inspection using the M-MDS.
(See DTC INSPECTION [RADAR UNIT].)

•  Is the same DTC present?

Yes

Replace the DSC HU/CM, then go to the next step.

(See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].)

(See DSC HU/CM REMOVAL/INSTALLATION [L.H.D.].)

No

Go to the next step.

5

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Clear radar unit DTCs using the M-MDS.
(See CLEARING DTC [RADAR UNIT].)

•  Switch the ignition ON (engine on).

•  Perform the radar unit DTC inspection using the M-MDS.
(See DTC INSPECTION [RADAR UNIT].)

•  Is the same DTC present?

Yes

Repeat the inspection from Step 1.

•  If the malfunction does not recur, go to the next step.

•  If the malfunction recurs, replace the radar unit.
(See RADAR UNIT REMOVAL/INSTALLATION.)

Go to the next step.

No

Go to the next step.

6

VERIFY THAT NO OTHER DTCs ARE PRESENT

•  Verify other DTCs displayed.

•  Are any other DTCs output?

Yes

Perform the corresponding DTC inspection.

No

DTC troubleshooting completed.

Step	Inspection		Action
1	PERFORM DTC INSPECTION FOR DSC HU/CM • Perform the DSC HU/CM DTC inspection using the M-MDS. (See DTC INSPECTION [DSC HU/CM].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [DSC HU/CM].) Then go to Step 5.
1		No	Go to the next step.
2	PERFORM DTC INSPECTION FOR SAS CONTROL MODULE • Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) (See DTC INSPECTION [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) (See DTC TABLE [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].) Then go to Step 5.
2		No	Go to the next step.
3	PERFORM DTC INSPECTION FOR BCM • Perform the BCM DTC inspection using the M-MDS. (See DTC INSPECTION [BCM].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [BCM].) Then go to Step 5.
3		No	Go to the next step.
4	PERFORM DTC INSPECTION FOR RADAR UNIT • Clear radar unit DTCs using the M-MDS. (See CLEARING DTC [RADAR UNIT].) • Switch the ignition ON (engine on). • Drive the vehicle at 40 km/h (25 mph) or more for 3 min or more. • Perform the radar unit DTC inspection using the M-MDS. (See DTC INSPECTION [RADAR UNIT].) • Is the same DTC present?	Yes	Replace the DSC HU/CM, then go to the next step. (See DSC HU/CM REMOVAL/INSTALLATION [R.H.D.].) (See DSC HU/CM REMOVAL/INSTALLATION [L.H.D.].)
4		No	Go to the next step.
5	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Clear radar unit DTCs using the M-MDS. (See CLEARING DTC [RADAR UNIT].) • Switch the ignition ON (engine on). • Perform the radar unit DTC inspection using the M-MDS. (See DTC INSPECTION [RADAR UNIT].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction does not recur, go to the next step. • If the malfunction recurs, replace the radar unit. (See RADAR UNIT REMOVAL/INSTALLATION.) Go to the next step.
5		No	Go to the next step.
6	VERIFY THAT NO OTHER DTCs ARE PRESENT • Verify other DTCs displayed. • Are any other DTCs output?	Yes	Perform the corresponding DTC inspection.
6		No	DTC troubleshooting completed.